Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > Beginners Beer Brewing Forum > Low Alcohol Level at Bottling Time
Reply
 
Thread Tools
Old 05-28-2013, 05:07 PM   #1
ThomasO
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: Dayton, OH
Posts: 37
Liked 2 Times on 2 Posts
Likes Given: 4

Default Low Alcohol Level at Bottling Time

I made up the Brewers' Best IPA adding a liquid yeast that the homebrew shop recommended as the only change. I've not gotten much bubbling activity the last few batches in the airlock, so didn't think much of it, and there is evidence of krausen activity when I opened the ale pale, but doing the math a few times after checking with the hygrometer, I come out with 1.44% alcohol after the initial was close to the recommended level (which I don't recall now). Taste is okay, with a somewhat grapefruity taste, which is okay to me since I like that flavor, but I suspect it isn't what it should be. I think I had some Sam Adams Double Agent IPA or something else similar that actually mentioned the grapefruit taste on the label so I'm not surprised by it, just wondered if I may have done something wrong. As far as I can see, I've followed the same cleaning and brewing procedures for 6 of these kits now, so I think I should be getting the hang of things. After a very good Scottish Ale and an Irish Stout, both of which came out very good in my opinion, but both of which showed very little bubbling activity, I just want to double check. Temps have been consistent with directions, no noticeable change to water conditions, same equipment and one-step cleanser, etc. 10 more days until I can open the first bottle and see how it ends up.

Tom Oxley


__________________
Beer, beer, beer said the sergeant
ThomasO is offline
 
Reply With Quote
Old 05-28-2013, 05:17 PM   #2
kh54s10
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
kh54s10's Avatar
Recipes 
 
Join Date: Aug 2011
Location: Tiverton, Rhode Island
Posts: 8,159
Liked 909 Times on 759 Posts
Likes Given: 237

Default

Have you calculated correctly.

This is the equation I see most often: ABV = (OG - FG)*131

OG= Original gravity (before fermentation)
FG= Final gravity (after fermentation is totally done)

Also make sure you are reading the hydrometer properly.

With kits, if you use all the ingredients, get the proper volume, and you get proper fermentation your ABV will be very close to the kits prediction.

BTW, when using liquid yeast for a 5 gallon batch you should make starters so you are pitching with the optimum cell count. A pack/vial will ferment the beer but do not contain the optimum cell counts.


kh54s10 is offline
 
Reply With Quote
Old 05-28-2013, 05:39 PM   #3
ThomasO
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: Dayton, OH
Posts: 37
Liked 2 Times on 2 Posts
Likes Given: 4

Default

I may well not have read the hydrometer correctly. I did follow the directions for the math several times. May get a new one or go over it with the homebrew supply store to make sure I'm reading it right. The level was just a little bit over the 5-gallon mark after I transferred to the bottling pale but that was after getting the reading, adding the cornstarch solution. I should have started pretty much at the 5-gallon line. I'll look at that yeast starting again and see about that on the next batch. Hoping to start the Cream Ale kit this weekend.

Tom Oxley
__________________
Beer, beer, beer said the sergeant
ThomasO is offline
 
Reply With Quote
Old 05-28-2013, 05:46 PM   #4
ncbrewer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2011
Location: New Bern, NC
Posts: 1,356
Liked 110 Times on 93 Posts
Likes Given: 104

Default

Quote:
Originally Posted by kh54s10 View Post
Have you calculated correctly.
And if so, what is the OG & FG? The OG should be almost exactly what the kit called for. Stratitication in the fermenter while pulling the sample can cause an incorrent OG reading. A high FG can happen, but probably not enough to result in 1.44% ABV, unless there's a big fermentation problem. If you got a really high FG, it would indicate a yeast problem of some kind - poor yeast health, wrong pitching or fermentation temperature, etc.
ncbrewer is offline
 
Reply With Quote
Old 05-28-2013, 06:20 PM   #5
gcdowd
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2011
Location: Baldwinsville, NY
Posts: 1,881
Liked 196 Times on 150 Posts
Likes Given: 5

Default

Are you by chance reading the alcohol scale and not the gravity scale?
__________________
God invented whiskey to keep the Irish from ruling the world.
gcdowd is offline
2
People Like This 
Reply With Quote
Old 05-28-2013, 06:38 PM   #6
CooperBrew
Feedback Score: 1 reviews
Recipes 
 
Join Date: Apr 2013
Location: Lakewood, Ohio
Posts: 175
Liked 34 Times on 23 Posts
Likes Given: 6

Default

Just a thought since I goofed this way on my first batch..... but are you taking the temperature of the sample and adjusting it to get the proper OG and FG? The hydrometer is calibrated to 0 at 60 degrees F. If your at a different temp you have to adjust the numbers accordingly to get an accurate reading.
I thought my first batch was way low as well. After finally being able to drink it it turned out just fine.
CooperBrew is offline
 
Reply With Quote
Old 05-28-2013, 07:16 PM   #7
wailingguitar
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2011
Location: Florence, Alabama
Posts: 1,656
Liked 114 Times on 96 Posts
Likes Given: 538

Default

It is quite possible that your OG was off due to incomplete mixing of the wort. This could result in an inaccurately low OG which, when compared with the FG, would give a false low ABV reading.
__________________
"Why did you.... what was the point of... how drunk were you when you decided this was a good idea?" - DMartin
wailingguitar is offline
 
Reply With Quote
Old 05-28-2013, 07:32 PM   #8
beergolf
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
beergolf's Avatar
Recipes 
 
Join Date: Jan 2011
Location: collingswood, nj
Posts: 4,863
Liked 639 Times on 489 Posts
Likes Given: 255

Default

Those are extract kits, so it is almost impossible to miss OG unless your volumes were waaaaay off. So you can use the OG listed in the recipe.

Take a good FG reading and use the formula that was list a few posts above. This should be accurate.
beergolf is offline
 
Reply With Quote
Old 05-28-2013, 07:58 PM   #9
ThomasO
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: Dayton, OH
Posts: 37
Liked 2 Times on 2 Posts
Likes Given: 4

Default

Thanks, all. I can't do much about it now but it all goes into the experience folder for the next batch. I may have looked at the wrong column on the hydrometer, and if I thought I was looking at the right one, naturally did it again for the FG. I mixed water to wort pretty well and stirred, so don't think that would be the problem. The 2 inches of krausen residue on the sides of the pale say I did get fermentation but not enough to bubble up through the air lock. I did notice the kitchen smelled very good during the process, and am wondering if my pale isn't sealing well. I'm getting another pale and lid for Fathers Day, intending to be able to do 2 batches every 3 weeks instead of 1, but if the new pale gives me very different results, then I may need to toss the old one or use it for something else, perhaps a secondary to use after fermentation has already started well. I was looking at temps and I did adjust the one point for the difference. I will read over the instructions again to make sure I understand the amount of adjustment. It's all about learning right now, and as long as the result is drinkable, it will work out.

Tom Oxley
__________________
Beer, beer, beer said the sergeant
ThomasO is offline
 
Reply With Quote
Old 05-28-2013, 08:01 PM   #10
Revvy
Post Hoc Ergo Propter Hoc
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
Revvy's Avatar
Recipes 
 
Join Date: Dec 2007
Location: "Detroitish" Michigan
Posts: 40,812
Liked 2874 Times on 1699 Posts
Likes Given: 3511

Default

Quote:
Originally Posted by ThomasO View Post
I mixed water to wort pretty well and stirred, so don't think that would be the problem.
Tom Oxley
You new brewers always seem to think that, but if that were the case we wouldn't have thousands of threads like this, and wouldn't have needed this thread entitled-"Attention new brewers, yes your original gravity reading is wrong. Don't panic"!

If you followed instructions, and have the correct volume of beer, then it's impossible to have that happen.


__________________
Like my snazzy new avatar? Get Sons of Zymurgy swag, here, and brew with the best.

Revvy's one of the cool reverends. He has a Harley and a t-shirt that says on the back "If you can read this, the bitch was Raptured. - Madman

I gotta tell ya, just between us girls, that Revvy is HOT. Very tall, gorgeous grey hair and a terrific smile. He's very good looking in person, with a charismatic personality... he drives like a ****ing maniac! - YooperBrew
Revvy is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
What determines the alcohol level? tristan1220 Cider Forum 12 09-25-2012 06:52 AM
Inconsistant alcohol level rsmith0061 Beginners Beer Brewing Forum 15 04-04-2012 03:39 PM
Raising the alcohol level garym58 Beginners Beer Brewing Forum 14 03-16-2012 03:27 PM
Does the alcohol-level increase in the bottle? 9/9 Beginners Beer Brewing Forum 1 12-17-2007 01:19 AM
how to increase alcohol level? calman Extract Brewing 25 05-14-2006 10:45 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS