Coldbreak Brewing Giveaway - Open to All!

Home Brew Forums > Home Brewing Beer > Bottling/Kegging > My Kegged Beer is Too Foamy
Reply
 
Thread Tools
Old 04-04-2013, 01:52 PM   #1
mkozlowski
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2010
Location: Massachussetts
Posts: 19
Default My Kegged Beer is Too Foamy

I'm kind of new at kegging and learning more as i go but recently i may have run into a little problem. It may be too early to say but my beer is way too foamy at 10-12psi.

I'll walk you through what i did:

I have a kegco kegerator with the dial set to the coldest setting (i believe they go to 38 degrees but i cant confirm mine is that cold).
Monday I syphoned a blueberry ale into the keg
attached the gas and set the pressure to 25psi
Let the keg sit over night to get it cold
Next day in an attempt to force carb i shook it for 15 mins (i thought that was the standard but now im thinking that was too long).
last night I dialed the psi down to 0
i pulled the pressure release to equalize the keg
attached my beer line
Opened the faucet
increased the psi up to 10-12psi to adjust for the pour

At this point the beer was mostly foam so i dialed it down to 8 psi and it was a little better but now the pour is super slow (and still a little foamy).

Is it because i shook it too long?
Is it over carbonated? based on the bubbles it almost doesnt seem carbonated enough.
Could my faucet be too warm?
Should i have waited longer to test?

If anyone has any videos they recommend or books on kegging? I didnt check to see if John Palmer has a section yet though im sure he does. Going to do that next.

But any help is appreciated.
Thanks.


mkozlowski is offline
 
Reply With Quote
Old 04-04-2013, 02:06 PM   #2
JDGator
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Location: Powassan, Ontario
Posts: 733
Liked 59 Times on 47 Posts
Likes Given: 8

Default

drop the pressure down to 3-4PSI and give it a pour. if it's still all foam then it's over-carbed. you can turn off the gas, keep pulling the relief and vent some CO2 or you can shake it some to help it come out faster. be careful with the shaking because when you pull the relief you may get a ton of beer out. i over carb mine lots because i get in a rush to drink it. LOL



Reason: add info
JDGator is offline
 
Reply With Quote
Old 04-04-2013, 02:06 PM   #3
kapbrew13
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2011
Location: somerset, NJ
Posts: 1,384
Liked 42 Times on 33 Posts

Default

Does it get better after a few pours? Doesn't sound like over carbonation.
kapbrew13 is offline
 
Reply With Quote
Old 04-04-2013, 02:11 PM   #4
forstmeister
Feedback Score: 1 reviews
Recipes 
 
Join Date: May 2011
Location: Chicago, IL
Posts: 1,211
Liked 181 Times on 137 Posts
Likes Given: 32

Default

Check your dip tube and your lid seal. A buddy had all foam recently in his kegerator and when I pulled the dip tube out there was a ding in the flange at the top. Just enough to suck air into the system when pouring. It foamed like crazy. Once we swapped it out it poured perfectly.
__________________
I drink (homebrew), therefore I am (gassy)
forstmeister is offline
 
Reply With Quote
Old 04-04-2013, 02:12 PM   #5
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
Vendor Ads 
Feedback Score: 3 reviews
 
Bobby_M's Avatar
Recipes 
 
Join Date: Aug 2006
Location: Whitehouse Station, NJ
Posts: 22,700
Liked 1263 Times on 833 Posts
Likes Given: 34

Default

My recommendation is to check out the sticky threads up at the top of the kegging forum. It's either overcarbed or your serving lines are way too short (probably both).
Bobby_M is online now
2
People Like This 
Reply With Quote
Old 04-04-2013, 02:13 PM   #6
mkozlowski
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2010
Location: Massachussetts
Posts: 19
Default

Thanks JD i'll give that a try later when i get home. When i pull the pin to reduce carb should i disconnect the gas? or leave that attached? and at what level?

Kapbrew, i'm not totally sure i'll have to try that as well. So far i just tried two glasses last night. i didnt want to waste any lol so i just waited for the foam to die down and drank it. After the foam went down though it was a little carbonated but it wasnt anything ferocious.

I really have to get a temp strip to leave in the fridge so i can see what temp it really is. How do i test when it comes out of the faucet? i've read that you lose some temperature to the pour and if its too warm it could make it foamy as well. I do have the fridge next to a heater (bad spot), but its the only place we really have room for it at the moment.

Thanks for the replies.
mkozlowski is offline
 
Reply With Quote
Old 04-04-2013, 02:13 PM   #7
mkozlowski
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2010
Location: Massachussetts
Posts: 19
Default

I'll take a look at that Bobby, thanks.
mkozlowski is offline
 
Reply With Quote
Old 04-04-2013, 02:15 PM   #8
JDGator
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Location: Powassan, Ontario
Posts: 733
Liked 59 Times on 47 Posts
Likes Given: 8

Default

Quote:
Originally Posted by mkozlowski View Post
Thanks JD i'll give that a try later when i get home. When i pull the pin to reduce carb should i disconnect the gas? or leave that attached? and at what level?

Kapbrew, i'm not totally sure i'll have to try that as well. So far i just tried two glasses last night. i didnt want to waste any lol so i just waited for the foam to die down and drank it. After the foam went down though it was a little carbonated but it wasnt anything ferocious.

I really have to get a temp strip to leave in the fridge so i can see what temp it really is. How do i test when it comes out of the faucet? i've read that you lose some temperature to the pour and if its too warm it could make it foamy as well. I do have the fridge next to a heater (bad spot), but its the only place we really have room for it at the moment.

Thanks for the replies.
you can disconnect the gas or you can just turn it off. keep pulling the relief every hour or so. may take up to a day to get it right. then turn the gas back on and set your serving pressure.
JDGator is offline
 
Reply With Quote
Old 04-04-2013, 02:19 PM   #9
kapbrew13
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2011
Location: somerset, NJ
Posts: 1,384
Liked 42 Times on 33 Posts

Default

There's also a utube vid on how to correct over carbonation. You could try that too. How long are you beer lines?
kapbrew13 is offline
 
Reply With Quote
Old 04-04-2013, 02:26 PM   #10
mkozlowski
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2010
Location: Massachussetts
Posts: 19
Default

Will check out the youtube vid... i watched some others on kegging but everyone seems to have their own opinion on it. Which makes it tricky... have to try a bunch of things and figure what works.

The lines though are the ones that came with the unit. I'll check the documentation later when i get home but if i had to guess id say they were 5 feet.


mkozlowski is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Im pissed my kegged beer is foamy Southern_Junior Bottling/Kegging 26 10-10-2012 03:12 PM
Foamy Beer?? szazman73 Bottling/Kegging 1 03-20-2012 05:47 AM
Kegged commercial beer-foamy pour erikrocks Bottling/Kegging 3 07-25-2011 08:06 PM
Kegged beer WAY too foamy..... pjk49202 Bottling/Kegging 19 07-15-2010 03:43 AM
foamy beer woodspointbrewer Bottling/Kegging 3 06-24-2009 05:45 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS