When does Phosphoric become noticeable? - Page 2 - Home Brew Forums
Home Brew Forums > Home Brewing Beer > General Techniques > When does Phosphoric become noticeable?

Reply
 
Thread Tools
Old 04-09-2013, 11:06 PM   #11
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 69,200
Liked 7699 Times on 5411 Posts


Quote:
Originally Posted by CharlosCarlies View Post
I prob should have included the disclaimer that these are pilot batches for a micro start-up I'm part of, so some options (like boiling specifically) eventually won't be realistic from an efficiency stand point. Lime softening is definitely something we have been looking into, however...so really appreciate the comments there.



Right, and from my understanding our water will almost surely be alkaline and not very hard (~50 ppm Ca and ~10 ppm Mg). From a water analysis that should be similar to ours, I've been estimating that we'll be around 200-250 ppm CaCO3. Given this, is lime softening likely going to be our best option? We'll have no issue adding back Ca since our water is also very low in chloride/sulfate.



Our chloride and sulfate will likely both be very low (~20-30 ppm) based off water reports I've seen near us.

As far as adding acid, I was under the impression that the acid reacted w/ the bicarbonate to reduce alkalinity, but also would leave behind sulfate, choride, lactate, etc depending on the particular acid being used. To me this seemed like a potential benefit since our chloride/sulfate levels are so low. Couldn't we just add hydrochloric/sulfuric acid and bump our low sulfate/chloride levels as well?
There are really two easy methods of removing alkalinity- boiling and then racking off the precipitate, or lime softening and racking off the precipitate. I can't think of many other cost-effective and easy ways but of course there are probably ways that breweries do this.
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 04-10-2013, 01:15 AM   #12
CharlosCarlies
Senior Member
HBT_LIFETIMESUPPORTER.png
 
CharlosCarlies's Avatar
Recipes 
 
Jan 2009
Conroe, TX
Posts: 713
Liked 9 Times on 7 Posts


Quote:
There are really two easy methods of removing alkalinity- boiling and then racking off the precipitate, or lime softening and racking off the precipitate. I can't think of many other cost-effective and easy ways but of course there are probably ways that breweries do this.
As I've started talking to more and more breweries, it's consistently amazed me how little thought goes into water chemistry. Of course some of these unnamed breweries are putting out very average beers, so I guess that's encouraging in a way.

We probably will end up using lime, but I got the acid idea from one of aj's posts a while back:

Quote:
Originally Posted by ajdelange View Post
It's fine to use acid to knock out alkalinity but there is a downside. Every milliequivalent of alkalinity you remove (this water has 122/50 = 2.4) is replaced by 1 milliequivalent of the anion of the acid you used. So if you knocked out all the alkalinity you'd replace the 2.4 mEq/L alkalinity with 2.4 mEq Lactate (same deal for sulfuric or hydrochloric). This should be kept in mind. Obviously everything is fine as long as you don't taste the lactate or dislike the effects of lots of chloride or sulfate.
Since our water is somewhat chloride/sulfate deficient anyways, the downside seems like a positive to me. Or am I totally wrong here?

Quote:
The lactic is somewhere in the range of 400-700 ppm.

Kai has done a lot of work in this area.
http://braukaiser.com/wiki/index.php...ash_pH_control
and
http://braukaiser.com/wiki/index.php...old_experiment
Awesome, thanks for the links!

 
Reply With Quote
Old 04-10-2013, 01:34 AM   #13
duboman
Recipes 
 
Jul 2011
Glenview, IL
Posts: 6,368
Liked 508 Times on 470 Posts


I have no idea of cost for this process but I know a large scale brewery that flash sterilizes their incoming water supply and then builds it back up to exactly what they want.
__________________
Nothing Left to do but smile and drink beer.....

The Commune Brewing Company-Perfecting the "art" of beer since 2010

 
Reply With Quote
Old 04-10-2013, 01:54 PM   #14
pjj2ba
Look under the recliner
HBT_LIFETIMESUPPORTER.png
 
pjj2ba's Avatar
Recipes 
 
Jul 2006
State College, Pennsylvania
Posts: 3,382
Liked 205 Times on 167 Posts


Sounds like your water might be similar to mine. Here's a thread I started that has my pre and post lime treatment results.

pre and post lime results

I also added some sodium metabisulfite which accounts for the gain in Na and Sulfur.

I works great for all of the beers I brew from pale lagers to stouts. For the dark beers, I wait to add the roasted malts until the end of the mash (as I ramp to mash out temps) so they don't end up affecting the mash pH. For the dark beers, I've taken to adding the precipitate back to the mash when I add the roasted malts. I'm still deciding if that makes a difference or not.

The only beer I make that I dilute with distilled water is my Czech pils. I brewed a test batch recently with out adding any distilled and the bitterness was not as smooth - at least initially. I has smoothed out a bit now. I may try again, but back off on the bittering hops and see if I can make it work without having to buy distilled water
__________________
On Tap: Doppelbock O'fest, Pale Ale, cider
Kegged and Aging/Lagering: CAP, Ger. Pils, OKZ (std Amer. lager), CZ Pils, Amer. Wheat, Rye IPA, Saison
Secondary:
Primary: Ger Pils, CAP
Brewing soon: Pale lager, Amer. wheat
Recently kicked : (
Pilsner Urquell Master Homebrewer
(1st NYC 2011, 2nd NYC 2012)
P U crowns winners in its inaugural master HB competition

 
Reply With Quote
Old 04-10-2013, 02:25 PM   #15
ajdelange
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Aug 2010
McLean/Ogden, Virginia/Quebec
Posts: 9,015
Liked 1400 Times on 1067 Posts


Quote:
Originally Posted by CharlosCarlies View Post
Since our water is somewhat chloride/sulfate deficient anyways, the downside seems like a positive to me. Or am I totally wrong here?
No, you are absolutely right. Should your alkalinity reduction acid requirement happen to balance your chloride/sulfate augmentation requirement you are indeed fortunate!

I don't usually recommend this approach to home brewers because I don't think they should be fooling with concentrated hydrochloric or sulfuric acids but given that this is a commercial setting with, presumably, all the safety equipment, MSDS.... in place then it can be a good way to go.

 
Reply With Quote
Old 04-11-2013, 01:00 PM   #16
CharlosCarlies
Senior Member
HBT_LIFETIMESUPPORTER.png
 
CharlosCarlies's Avatar
Recipes 
 
Jan 2009
Conroe, TX
Posts: 713
Liked 9 Times on 7 Posts


Quote:
No, you are absolutely right. Should your alkalinity reduction acid requirement happen to balance your chloride/sulfate augmentation requirement you are indeed fortunate!
This is great, great news! My last question is even though the alkalinity is reduced, is there any negative effect on flavor vs just having low alkaline water to begin with? (assuming similar sulfate/chloride profiles)

Quote:
I don't usually recommend this approach to home brewers because I don't think they should be fooling with concentrated hydrochloric or sulfuric acids but given that this is a commercial setting with, presumably, all the safety equipment, MSDS.... in place then it can be a good way to go
Yep, yep. I still don't look forward to using them, but w/ the right safety measures in place it's starting to sound like a viable option.

 
Reply With Quote
Old 04-11-2013, 02:35 PM   #17
ajdelange
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Aug 2010
McLean/Ogden, Virginia/Quebec
Posts: 9,015
Liked 1400 Times on 1067 Posts


No, there shouldn't be. You have simply replaced the bicarbonate ions with sulfate and chloride ions. The calcium/magnesium/sodium are already there. Were you to start with RO/DI water you would have to add calcium/magnesium/sodium sulfate and chloride to get the anion profile you want. You would end up with the same water.

 
Reply With Quote
Old 04-11-2013, 10:04 PM   #18
CharlosCarlies
Senior Member
HBT_LIFETIMESUPPORTER.png
 
CharlosCarlies's Avatar
Recipes 
 
Jan 2009
Conroe, TX
Posts: 713
Liked 9 Times on 7 Posts


We'd likely have to add some calcium back when using lime as well, right? Makes me like the acid option more and more. Only issue is, like you mentioned, keeping it safe.

 
Reply With Quote
Old 04-12-2013, 01:29 PM   #19
pjj2ba
Look under the recliner
HBT_LIFETIMESUPPORTER.png
 
pjj2ba's Avatar
Recipes 
 
Jul 2006
State College, Pennsylvania
Posts: 3,382
Liked 205 Times on 167 Posts


Quote:
Originally Posted by CharlosCarlies View Post
We'd likely have to add some calcium back when using lime as well, right? Makes me like the acid option more and more. Only issue is, like you mentioned, keeping it safe.
It is not to difficult to be safe. I would recommend making a diluted stock, say to around 10-20% and use that. That way you don't handle the concentrated stuff as much. I might also suggest a rubber "boot" to carry the bottle of concentrated stuff around in case the bottle brakes (droppage, hit something, etc).

And ALWAYS add acid to water, NOT water to acid. Quite a bit of heat is generated when the two are mixed and if you add it backwards it can cause a vigorous enough reaction to splash - even if gently poured. No problems if you add them in the right order.

I was taught, "do as you aughta', add acid to wata'"
__________________
On Tap: Doppelbock O'fest, Pale Ale, cider
Kegged and Aging/Lagering: CAP, Ger. Pils, OKZ (std Amer. lager), CZ Pils, Amer. Wheat, Rye IPA, Saison
Secondary:
Primary: Ger Pils, CAP
Brewing soon: Pale lager, Amer. wheat
Recently kicked : (
Pilsner Urquell Master Homebrewer
(1st NYC 2011, 2nd NYC 2012)
P U crowns winners in its inaugural master HB competition

mbobhat Likes This 
Reply With Quote
Old 04-12-2013, 01:44 PM   #20
solbes
Recipes 
 
Jul 2011
Ramsey & Akeley, Mn
Posts: 2,975
Liked 237 Times on 217 Posts


"Acid to Base, to Save Your Face" is how I learned that one.

I'm learning lots in this thread, very interesting. On a homebrewer scale its much easier to just cut your water with RO and add some lactic to balance pH. But I suppose that would be a very expensive system if you are requiring large volumes of water.
__________________
Primary #1: Umlaut my Kölsch VII #2: Empty
Secondary #1
: Empty #2: Empty #3: Cab MerMarqeNac Wine
Kegged
: Mugged a Monk Paters
Bottles
: Dark Belgian Strong, Black Raspberry Rhubarb wine, RIS, Carmel Apple Cider, Big 50 Barleywine, Framboise Lambic, Barolo Wine, Berry Rhubarb Wine, Black Currant wine
On Deck: BGSA

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
How many OG points are noticeable? pj_rage General Beer Discussion 5 12-06-2010 01:37 PM
Swamp cooling - noticeable difference? jkreuze General Techniques 24 08-18-2010 02:15 PM
Enough oak to be noticeable? KyleWolf Recipes/Ingredients 14 08-09-2010 06:12 PM
Noticeable Signs of Infection Brutus Brewer Equipment/Sanitation 1 09-15-2009 03:19 PM
Noticeable Legs gxm Recipes/Ingredients 7 12-02-2008 05:24 PM


Forum Jump