Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > General Beer Discussion > Hallelujah, whirlpooling works!
Reply
 
Thread Tools
Old 03-25-2013, 10:21 PM   #1
HenryMoon
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 6
Liked 3 Times on 1 Posts
Likes Given: 2

Default Hallelujah, whirlpooling works!

So, I've been brewing all grain for about 2 years total. I had to take off for about 18 months due to a job transfer. (Moved into a rent house while building new, didn't want to set up brewery and have to tear it back down.) Anyway, I've made a total of 59 batches. The first 58 batches, I would throw in the Whirlfloc and immersion chiller and boil the last 15 minutes of my boil. Then chill the wort to fermentation temps, pull the chiller and swirl the wort and wait 10 - 15 minutes. All I would get would be a fluffy sediment in the bottom of my pot, suspended equally across the entire bottom of the pot, no cone at all. Recently I bought a new Therminator chiller and used it on my last batch this past Sunday. I had decided that I wasn't going to even try whirlpooling anymore, as I had no luck in the past, but I decided to try it one last time to see if wort temps had anything to do with it. I turned the fire off my brew pot at the end of the hour, gave the wort a good swirl and waited 10 minutes to start my transfer to the carboy. As my pot was draining and I began to get to the bottom, much to my surprise, there was an almost perfect cone right there in the center of my pot. It was almost like a miracle, I had to wipe a tear from my eye! Anyway, maybe I'm the last person in the hobby to know this, but I wanted to pass this along to anyone else that may have not known why whirlpooling didn't work for them. I'm not sure what the solution would be for those using immersion chillers, but there are much smarter people on here than I that could suggest solutions for that. Batch 59 - perfect cone! Oh, and by the way - the Therminator is almost magical. Hard to believe that you can drain 208 degree wort through that and it go into the carboy at a nice 66 degrees.


HenryMoon is offline
 
Reply With Quote
Old 03-25-2013, 10:30 PM   #2
Brewskii
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: Williamsburg, Va
Posts: 1,167
Liked 121 Times on 67 Posts

Default

I've got the same story with the twist being whirl pooling worked well for me as long as I gravity drained very slowly to the fermenter.
When I got my Therminator I didnt see a way to whirlpool with a strainer in the brew kettle so I opted to pump thru the Therminator at flame out which leads to scraping the bazooka screen with a spoon basically the whole time.

I love the Therminator but how'd you manage a whirlpool with a hop screen in place? Or are you even using a hop screen?


Brewskii is offline
 
Reply With Quote
Old 03-25-2013, 10:36 PM   #3
HenryMoon
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 6
Liked 3 Times on 1 Posts
Likes Given: 2

Default

Didn't use a hop screen and from what I saw yesterday, it won't be needed. The wort was extremely clear and clean with almost all of the hop material settled in the cone. And when I say almost, I'm talking 95 - 99 percent!
HenryMoon is offline
 
Reply With Quote
Old 03-25-2013, 10:40 PM   #4
Mojzis
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: Rochester, NY
Posts: 1,233
Liked 139 Times on 99 Posts
Likes Given: 101

Default

I just installed a whirlpool pickup and made a cfc and had the same reaction as you. Loving it
Mojzis is offline
 
Reply With Quote
Old 03-25-2013, 11:40 PM   #5
Brewskii
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: Williamsburg, Va
Posts: 1,167
Liked 121 Times on 67 Posts

Default

Quote:
Originally Posted by HenryMoon
Didn't use a hop screen and from what I saw yesterday, it won't be needed. The wort was extremely clear and clean with almost all of the hop material settled in the cone. And when I say almost, I'm talking 95 - 99 percent!
At $200 for the plate chiller, I'm a little hesitant to risk running hop material through it even if it's just a little. My whirlpools always ended up with at least some trub and hop particles in the fermenter..

I'm not afraid of plugging it or fouling it so much as getting a pocket of crud inside it leading to infections.
Brewskii is offline
 
Reply With Quote
Old 03-25-2013, 11:47 PM   #6
HenryMoon
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 6
Liked 3 Times on 1 Posts
Likes Given: 2

Default

To clean they suggest running a PBW mixture through it in reverse. I did this, dumping the first gallon out, then simply recirculated for about five minutes. Then pumped through plain hot water to rinse. Soak in starsan on brew day while brewing, I'm not at all worried about contamination.


HenryMoon is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Whirlpooling ChargersSB General Techniques 18 02-08-2012 09:44 PM
whirlpooling captainoverspray General Beer Discussion 9 01-05-2012 04:28 AM
Whirlpooling hoptopia General Techniques 1 10-27-2011 09:30 PM
Whirlpooling Skins_Brew Beginners Beer Brewing Forum 3 12-31-2007 06:50 PM
Whirlpooling PanzerOfDoom Beginners Beer Brewing Forum 1 02-04-2006 11:24 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS