First brew day - Home Brew Forums
Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > First brew day

Reply
 
Thread Tools
Old 03-23-2013, 05:08 PM   #1
scotty2
Recipes 
 
Feb 2013
Posts: 75
Liked 4 Times on 4 Posts



Been reading for quite awhile. Decided to skip extract and go right to AG. Built a MT out of a 10gal Rubbermaid cooler and a stainless braid. Decided to do a 2.5 gal batch as basically a throw away as I know there will be a lot of mistakes. I know 2.5 gals is too small a batch for the 10 gal MT. Bought hose clamps that were too big for the braid, so I duct taped it in. Despite all that, hit my mash temp of 153(märzen/Oktoberfest), and sparged without incident. Boil went fine, cooling took quite awhile in my sink. OG way way low, somehow I overshot the water by quite a bit. Added some DME to get post boil gravity up a bit. Pitched a vial of WL Oktoberfest yeast, didn't make a starter. All in all, I think it went well. When I get all the proper equipment, I'm confident I can get it right. I made my own recipe and grain bill and got from point A to point B, it's now fermenting at 55.



Click image for larger version

Name:	image-3546711933.jpg
Views:	200
Size:	33.8 KB
ID:	109951



 
Reply With Quote
Old 03-23-2013, 05:22 PM   #2
NivekD
Recipes 
 
Dec 2012
West Jordan, Utah
Posts: 664
Liked 101 Times on 83 Posts


You added DME without boiling it? Not a good idea...but it may turn out...only time will tell.


__________________
Bottled: Mexican Cerveza, Irish Stout, some Blue Moon clone, Pepper Ale, Full Hard Lemonade, Russian Imperial Stout, My first attempt at Mead (JAOM), Black Pearl Porter
Kegged: Blue Moon clone, Irish Red Ale
On Deck: Citra Hop Bomb (small batch) and Cream of Three Crops

_______________________________________________

Never underestimate the power of stupid people in large groups.

 
Reply With Quote
Old 03-23-2013, 05:29 PM   #3
scotty2
Recipes 
 
Feb 2013
Posts: 75
Liked 4 Times on 4 Posts


I was more interested in trying to get to the gravity. Like I said, basically a throw away, just looking to get through the entire process. I knew beforehand I might be dumping it.

 
Reply With Quote
Old 03-24-2013, 03:06 AM   #4
Cyclman
I Sell Koalas
HBT_LIFETIMESUPPORTER.png
 
Cyclman's Avatar
Recipes 
 
Jan 2013
Aurora, CO
Posts: 6,156
Liked 722 Times on 604 Posts


I would recommend using an AG kit to start. That way, the recipe isn't a variable in your quality, just your process.

Welcome, best luck!
__________________
Give a man a beer, waste an hour. Teach a man to brew, and waste a lifetime! Bill Owen quote

Why does Happy Hour limit happiness to 1/24 of the day?

 
Reply With Quote
Old 03-25-2013, 09:33 PM   #5
scotty2
Recipes 
 
Feb 2013
Posts: 75
Liked 4 Times on 4 Posts


Quote:
Originally Posted by Cyclman
I would recommend using an AG kit to start. That way, the recipe isn't a variable in your quality, just your process.

Welcome, best luck!
I had that idea, but, I wanted to draw up my own grain and hop bills. I'm satisfied that I was able to cross the finish line without any real technical difficulties. My airlock started to bubble, so, I got there, it just might not be any good. Yes, the kit would certainly eliminate a huge variable.

 
Reply With Quote
Old 03-25-2013, 11:19 PM   #6
jamieofthenorth
Recipes 
 
May 2012
, Maine
Posts: 47
Liked 5 Times on 4 Posts


Nice! Good plan with being okay with truly throwing away the throw away batch should it be needed. I'd recommend getting those hose clamps to replace the duct tape before the next batch, but I'm guessing you already plan to do that.

 
Reply With Quote
Old 03-26-2013, 12:29 AM   #7
scotty2
Recipes 
 
Feb 2013
Posts: 75
Liked 4 Times on 4 Posts


Quote:
Originally Posted by jamieofthenorth
Nice! Good plan with being okay with truly throwing away the throw away batch should it be needed. I'd recommend getting those hose clamps to replace the duct tape before the next batch, but I'm guessing you already plan to do that.
Doing away with the braid altogether. Buying a stainless bucket strainer seen in the "mash in a bucket" thread. At $150 shipped, it's only slightly more than a false bottom.

jamieofthenorth Likes This 
Reply With Quote
Old 04-10-2013, 03:41 AM   #8
DogFace_Brewing
Recipes 
 
Jan 2011
Huntley, IL
Posts: 250
Liked 8 Times on 7 Posts


Quote:
Originally Posted by scotty2 View Post
Doing away with the braid altogether. Buying a stainless bucket strainer seen in the "mash in a bucket" thread. At $150 shipped, it's only slightly more than a false bottom.
Looks like you are going all in with this hobby...I would suggest just keeping the braided hose and get the clamps for now...nothing wrong with that process and $150 will buy you ALOT of grain! Cheers!

 
Reply With Quote
Old 04-10-2013, 04:44 AM   #9
scotty2
Recipes 
 
Feb 2013
Posts: 75
Liked 4 Times on 4 Posts


Quote:
Originally Posted by DogFace_Brewing

Looks like you are going all in with this hobby...I would suggest just keeping the braided hose and get the clamps for now...nothing wrong with that process and $150 will buy you ALOT of grain! Cheers!
Too late!


Click image for larger version

Name:	image-819894999.jpg
Views:	64
Size:	33.9 KB
ID:	114569  

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
New brew schedule... or how to brew with toddlers! (input/advice sought!) Zymurgrafi All Grain & Partial Mash Brewing 56 10-22-2013 05:22 PM
!!!new home brew supply and craft brew store in shreveport!!! MJoyner South Central Homebrew Forum 3 06-25-2013 09:13 PM
Next recipe : Festa Brew Double Outmeal or Micro Brew Imperial Stout? beauvafr Recipes/Ingredients 2 12-05-2012 12:50 AM
brew craft deluxe home brew kit all you need to make beer cowboybuckup For Sale 20 07-01-2012 05:16 AM
Brew Shop closed. Best yeast to buy for hard apple cider brew? britishbloke Beginners Beer Brewing Forum 8 01-10-2007 03:48 AM


Forum Jump