Can't Tell if Fermwrap is working - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Can't Tell if Fermwrap is working

Reply
 
Thread Tools
Old 02-10-2013, 01:15 PM   #1
ITbrewer229
Recipes 
 
Feb 2013
Poughkeepsie, New York
Posts: 31
Liked 1 Times on 1 Posts



I just bought a new Fermwrap heater with a Johnson Controller. Last night my carboy dropped to 60 degrees from a 70 degree setpoint.

The Controller appears to be calling for heater to be on but to take that out of the equation, I plugged the Fermwrap directly into outlet and it still feels room temp. Should it at least feel warm? I'm trying to figure out if I need to contact vendor that it's faulty.

Thanks in advance!



 
Reply With Quote
Old 02-10-2013, 08:09 PM   #2
NormB
Recipes 
 
Jun 2012
Marlton, NJ
Posts: 11
Liked 7 Times on 5 Posts


I experienced the same thing. I was given the fermwrap by a friend and it had never been opened. I called Fermentap to ask how long it should take to warm up. We determined it was defective. Because it was a gift I had no receipt. However, the customer service rep was able to look up my friend's name and confirm he had purchased one. They sent a replacement free of charge (despite having no receipt to show). I have not yet used it, but have plugged it in and could feel the warmth rather quickly. I haven't used it yet as I found an old heating pad to use in the fermentation chamber while I awaited the new fermwrap. Good luck!



 
Reply With Quote
Old 02-10-2013, 08:18 PM   #3
Stick
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Jan 2009
Raleigh, NC
Posts: 37
Liked 1 Times on 1 Posts


I have been using mine for a while now and it gets warm to the touch fairly quickly. It never gets "hot" (a good thing) but you should be able to tell a defn difference from on and off.

 
Reply With Quote
Old 02-10-2013, 08:22 PM   #4
mpcluever
Recipes 
 
Jun 2010
here
Posts: 635
Liked 39 Times on 34 Posts


I've also had the little clips where it attaches to the wrap come loose. Clamping them tighter fixed it.

 
Reply With Quote
Old 02-10-2013, 10:51 PM   #5
ITbrewer229
Recipes 
 
Feb 2013
Poughkeepsie, New York
Posts: 31
Liked 1 Times on 1 Posts


Thanks everyone for the replies.

The clamps are good and I know the controller works because I found a heating pad that I used with the Johnson controller which looks like it saved the day. Carboy temp at 69 degrees now.

I'm going to reach out to the vendor regarding the Fermwrap.

Thanks again!

 
Reply With Quote
Old 02-12-2013, 02:34 PM   #6
ITbrewer229
Recipes 
 
Feb 2013
Poughkeepsie, New York
Posts: 31
Liked 1 Times on 1 Posts


So I reached out to the vendor (www.morebeer.com). I stumbled across these guys in my Brew Your Own subscription and decided to give them a try. They really do rock.

When I told them about the Fermwrap, they immediately replaced it (had a tracking number by the end of the same day) and was told I don't need to worry about sending the old one back.



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY - Fermwrap help kevinb Fermenters 10 10-21-2013 10:03 PM
Fermwrap - 2 for 1? BoogieBrandBooze Fermenters 36 03-27-2013 07:39 PM
Using a Fermwrap all by itself!!! Taygel Fermentation & Yeast 5 04-01-2011 04:37 PM
Using Fermwrap all on its own Judochop Equipment/Sanitation 4 04-13-2010 04:21 PM


Forum Jump