What's the width of your monstermill? Fit hopper to Schmidling attempt. - Home Brew Forums
Home Brew Forums > Home Brewing Beer > DIY Projects > What's the width of your monstermill? Fit hopper to Schmidling attempt.

Reply
 
Thread Tools
Old 01-30-2013, 06:04 PM   #1
Infidel
Recipes 
 
May 2008
Austin, don't move here. We don't have water or space, traffic is plentiful.
Posts: 84
Liked 7 Times on 6 Posts



I'm trying to order the hopper from monstermill, and trying to get the measurement of the width of different models.
What I have here is a Schmidling, and want to fit the hopper from monstermill because it seems to have the best engineering. I'll use rivets instead of the #8 screws to assemble it - assuming I can find one that is 3.5" wide.
I'll be replacing the particle board sides with aluminum. Why aluminum instead of stainless? This has the corn option, which means I can adjust the case hardened rollers so wide they will grind up against it. Better to have them eat through aluminum than destroy them on stainless. It also means they can also be adjusted so close that they will contact each other.
The only reason I might go with stainless is in case I need to weld. I don't have the resources to weld aluminum.
I'll put a small port on the top to easily inspect and measure the gap which will double as a shop vac attachment point for cleaning.

-Cheers

Exchanged message with Fred, very helpful. It won't work as is, but I may try it with some mod's. Need to find the width of one of the 2.0 mills. If I only had room for a sheet metal brake.


Click image for larger version

Name:	millwidth.jpg
Views:	390
Size:	39.3 KB
ID:	97526  

 
Reply With Quote
Old 01-31-2013, 01:39 AM   #2
beaksnbeer
HBT_LIFETIMESUPPORTER.png
 
beaksnbeer's Avatar
Recipes 
 
May 2011
New Port Richey, Florida
Posts: 2,844
Liked 505 Times on 334 Posts


Except the aluminum shavings will end up in the mash, don't think I'd go there. I used Lexan on my fully adjustable malt mill. I have run corn through mine no problems.


__________________
Quote:
Home of the 12 Tap keezer

Stealthcruiser Likes This 
Reply With Quote
Old 01-31-2013, 02:31 AM   #3
Infidel
Recipes 
 
May 2008
Austin, don't move here. We don't have water or space, traffic is plentiful.
Posts: 84
Liked 7 Times on 6 Posts


good idea, scraped any lexan off yet?
is your bird prone to hangovers?

 
Reply With Quote
Old 01-31-2013, 09:08 PM   #4
beaksnbeer
HBT_LIFETIMESUPPORTER.png
 
beaksnbeer's Avatar
Recipes 
 
May 2011
New Port Richey, Florida
Posts: 2,844
Liked 505 Times on 334 Posts


My mill

Click image for larger version

Name:	image-650411884.jpg
Views:	158
Size:	33.1 KB
ID:	97816



Click image for larger version

Name:	image-2500028562.jpg
Views:	155
Size:	40.6 KB
ID:	97817



Click image for larger version

Name:	image-1104601318.jpg
Views:	150
Size:	51.4 KB
ID:	97818
__________________
Quote:
Home of the 12 Tap keezer

 
Reply With Quote
Old 11-20-2013, 06:45 PM   #5
biertourist
Recipes 
 
Oct 2012
Woodinville, WA
Posts: 861
Liked 124 Times on 93 Posts


This is one of the most beautiful DIY projects on here; so cool to be able to watch the milling up close and personal; great job!

Afraid of what this cost, though. (I love the directly driven 2 roller option, but the cost of entry is steep.)



Adam

 
Reply With Quote
Old 11-21-2013, 06:09 PM   #6
Infidel
Recipes 
 
May 2008
Austin, don't move here. We don't have water or space, traffic is plentiful.
Posts: 84
Liked 7 Times on 6 Posts


That is a very nice build! How does the lexan next to the rollers hold up to scratching?

Completed everything but the motor mount.
The project was a pain in the something, should have just made it from all stainless so it could be welded with what I have on hand - DCEN TIG.

Anyone have any suggestions besides simply drilling into the base board? I would like a little adjustment to allow for a change of pulley or belt size. Two to three inches of travel is what I have in mind. Only option I've seen pre-made is $150 range. I can manufacture most things, but don't have a lathe / mill. Enough scrap steel around that something should be possible. Again, a sheet metal brake would be useful.

Some rivets were a good idea, but doing the entire thing with them was like doing a jigsaw puzzle. Went to a specialty store and had them tell me which rivets to use, the ones that came with the HF rivet gun were useless for my application.


Used a router to cut a circular groove in the base so it fits over a bucket.

Went with polycarbonate on one side - the adjustable one.

I'll have an extra aluminum / polycarbonate set for sale to a Schmidling maltmill owner that is interested in replacing the factory particle board.

 
Reply With Quote
Old 11-21-2013, 06:28 PM   #7
beaksnbeer
HBT_LIFETIMESUPPORTER.png
 
beaksnbeer's Avatar
Recipes 
 
May 2011
New Port Richey, Florida
Posts: 2,844
Liked 505 Times on 334 Posts


No scratching after 600lbs of grain and 250lbs of corn. The poly doesn't touch the rollers it's close but doesn't touch.


__________________
Quote:
Home of the 12 Tap keezer

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Schmidling Malt Mill parratt1 Equipment/Sanitation 17 03-29-2014 10:40 PM
MonsterMill thumbscrew tighness and gap adjustment dcbw Equipment/Sanitation 8 12-03-2012 10:05 PM
My Schmidling MaltMill has arrived! schneemann Equipment/Sanitation 14 06-30-2012 12:26 AM
Schmidling Malt Mill HomerJR All Grain & Partial Mash Brewing 4 12-07-2009 11:44 PM
Schmidling mills? hexmonkey Equipment/Sanitation 10 03-05-2009 12:05 AM


Forum Jump