Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Consistently low efficiency
Reply
 
Thread Tools
Old 01-30-2013, 02:05 PM   #1
Hemicharger99
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: Buffalo, NY
Posts: 21
Likes Given: 1

Default Consistently low efficiency

I've been an avid homebrewer for over 8 years now and made the jump to all grain last year. I've upgraded most of my equipment and purchased a 40qt rectangular cooler with custom manifold, crankandstein 3E, pH meter, and 2 temperature probes.

I've consistently only received around 58-62% efficiency for any recipe. An example of a recipe is listed below.

5 gallon batch size
Single infusion
14.5 lbs grain bill
18.13 qts of water for mash-in (1.25:1 ratio)
11.8 qts of water for fly sparge


The rectangular manifold was designed with input from the How To Brew book regarding spacing between the sides and number of runs to the drain. It's all copper and connects via silicon hose to the output.

My temperature has always been within 1 to 2 of target and the pH has always been 5.2 or 5.3 without the use of any buffers. I've measured the gap in the grain mill and it is about .045".

Any ideas would be greatly appreciated.


Hemicharger99 is offline
 
Reply With Quote
Old 01-30-2013, 02:14 PM   #2
AnOldUR
fer-men-TAY-shuhn
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
AnOldUR's Avatar
Recipes 
 
Join Date: Mar 2007
Location: New Jersey
Posts: 6,816
Liked 764 Times on 558 Posts
Likes Given: 621

Default

Do you have a picture of your crush? .045 gap could be your problem.

Are you stirring really well after adding grain? Dough balls, break up starches.

Are you sure you're not getting channeling? Try a batch sparge with a lot of stirring.


__________________
Sent from my POS computer because I refuse to own a smartphone!
AnOldUR is offline
 
Reply With Quote
Old 01-30-2013, 02:22 PM   #3
deadfall
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
deadfall's Avatar
Recipes 
 
Join Date: Aug 2012
Location: Hammondsport, New York
Posts: 354
Liked 83 Times on 41 Posts
Likes Given: 296

Default

Crush seems to be the most obvious. I'd tighten and see if that changes anything.
deadfall is offline
 
Reply With Quote
Old 01-30-2013, 03:11 PM   #4
MBTB
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2013
Posts: 79
Liked 5 Times on 5 Posts

Default

I would close that gap to .030-.035" and like AnOldUR said, try batch sparging. With 14.5 lbs. of grain you should have gotten 1.080-1.087 with 1.25 qts. per lb mash and 2 qts. per lb batch sparge. Yes it is a lot of water to boil off, but thats how to get higher efficiency.
MBTB is offline
 
Reply With Quote
Old 01-30-2013, 05:44 PM   #5
MrTheKing
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: Denver, CO
Posts: 134
Liked 10 Times on 10 Posts

Default

My biggest increase in efficiency was realizing I wasn't stirring enough. I had bought a grain mill, tightened it up and was still getting around 70%, not much better than at my LHBS mill. Stirring really well at dough in, for 3-5 minutes before mashout, and then for 5 minutes after adding sparge and i'm consistently at 85% now.

Stir like crazy, then stir some more.
MrTheKing is offline
 
Reply With Quote
Old 01-30-2013, 06:51 PM   #6
Hemicharger99
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: Buffalo, NY
Posts: 21
Likes Given: 1

Default

I usually stir during the initial add of the grains to the mash tun to break up the dough balls, and maybe once or twice throughout the mash process.

I'll try to adjust the mill for the next round of brewing on an IPA. I'll shoot for the low end around .030".

When I designed the manifold, I did it to avoid channeling and followed the general rules of thumb on them.

I went through all the stickies on here too just to make sure that I had everything covered before I posted. Thanks for the advice, I'll let you know how it turns out.
Hemicharger99 is offline
 
Reply With Quote
Old 01-30-2013, 07:33 PM   #7
duboman
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2011
Location: Glenview, IL
Posts: 6,365
Liked 506 Times on 468 Posts
Likes Given: 226

Default

I can almost guarantee you that adjusting the mill gap to .035 will net you a solid 10-15 percent better efficiency since the rest of your process is pretty spot on!
__________________
Nothing Left to do but smile and drink beer.....

The Commune Brewing Company-Perfecting the "art" of beer since 2010
duboman is offline
 
Reply With Quote
Old 01-30-2013, 08:36 PM   #8
Hemicharger99
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: Buffalo, NY
Posts: 21
Likes Given: 1

Default

Good to know! And thanks for the help! I don't mind throwing extra grain at it, but in the case of a Belgian Quad, I'm going to need the room for the standard grain bill and the mash /sparge water. Last one topped me out when it came out to 1.108. (With Candi Sugar)
Hemicharger99 is offline
 
Reply With Quote
Old 02-01-2013, 05:59 AM   #9
chri5
Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2008
Location: Sacramento, CA
Posts: 337
Liked 16 Times on 15 Posts
Likes Given: 53

Default

Like everybody above said, it usually comes down to the crush. Depending upon which LHBS I go to, I know if I need to include an extra pound of grain in my recipe to account for hte poor crush. My friend and I call it the "brewmeister tax", since I need to buy extra grain at the lhbs named "brewmeister". lol


chri5 is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Consistently low efficiency - what's my problem? musikguru6 All Grain & Partial Mash Brewing 16 01-27-2013 06:26 PM
Consistently low FG brewser7 Beginners Beer Brewing Forum 13 04-15-2012 03:02 PM
Consistently (really) low efficiency, here's my notes. mother_night All Grain & Partial Mash Brewing 43 03-25-2012 08:22 PM
Consistently Poor Efficiency SeanS86 All Grain & Partial Mash Brewing 14 05-06-2011 04:29 AM
Consistently not getting the FG I want dunnright00 General Techniques 14 03-06-2011 04:37 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS