VISSANI Build - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > DIY Projects > Kegerators & Keezers > VISSANI Build

Reply
 
Thread Tools
Old 01-22-2013, 12:41 AM   #1
aarong
 
aarong's Avatar
Recipes 
 
Jan 2012
Newport, RI
Posts: 212
Liked 20 Times on 17 Posts



Here is a vissani build that I have just finished. I wanted to post instructions on how to DIY. It is a very clean looking fridge everything is self contained with no external boxes.

Here is the final product with the fridge closed. It is the front closed and a picture of the back. The outlet is split one is hot and one is for cold.

My inspiration was from Ingchr's vissani fermentation chamber

I wanted to build it using a STC 1000 but wanted to install it inside the fridge so you can read it through the glass
Click image for larger version

Name:	IMG_1514.jpg
Views:	1117
Size:	48.2 KB
ID:	95823   Click image for larger version

Name:	IMG_1512.jpg
Views:	938
Size:	32.6 KB
ID:	95824  

KurfBrew Likes This 
Reply With Quote
Old 01-22-2013, 01:04 AM   #2
aarong
 
aarong's Avatar
Recipes 
 
Jan 2012
Newport, RI
Posts: 212
Liked 20 Times on 17 Posts


So for the build. I bought the vissani fridge for $70.00 which is way below the average cost it is normally in the low to mid $100.00 range on sale. I bought all my parts from Homedepot besides the STC 1000 from newegg.com

Part list:
STC 1000 $24.00
20' of 300V rubber power cord for $0.48/ft I got 20 feet
1 gang Outlet Box $2.74
100 W light bulb (at home)
15 AMP outlet $1.19
Empty paint can $2.97
Face plate $0.62
Black outlet plate $0.47
Hez nut 4mm-7hex $0.50
Standard screw (any old one will work around 1 inch)
15 A plug $2.97
Weatherproof socket for the light bulb $3.28
Machine screw 4mm-.7 x 20mm $0.96
White plug 15A $1.99
1 gang low voltage bracket $1.65

Total $53.00

Note there is extra pieces in the photo but you only need what is on the list
Click image for larger version

Name:	IMG_1489.jpg
Views:	839
Size:	58.6 KB
ID:	95832  

 
Reply With Quote
Old 01-22-2013, 01:18 AM   #3
aarong
 
aarong's Avatar
Recipes 
 
Jan 2012
Newport, RI
Posts: 212
Liked 20 Times on 17 Posts


I am in no way an expert electrician or an expert in refridgeration. Conduct this build at your own risk. Have fun and be safe.
So here we go:

First I bypassed the thermostat according to Ingchr's post

2) Cut the tabs off the back of the 1 gang low voltage bracket this will allow it to fit perfectly under the built in thermostat control of the fridge(Pic1) Then clean up the side of the orange bracket. I used a box cutter

3) Cut a square the size of the STC panel in the solid face plate. This was the hardest part of the project for me. I used a box cutter to score it then I used anything I had to cut it out. I would recommend a dremel. (Pic 2)

4) Screw the face plate on the orange box with included screws. (Pic 3)

5) Remove the thermostat box/ light attachment on the top of the fridge. This is simply unscrewing two screws under the box. Pull down and toward you and it will come right off.

6)Unhook the light. Pull the white thermostat straight off and unscrew the thermometer. Remember where the wires where that you pulled off of the thermostat so you can put it back on. The whole black thermostat box will separate from the fridge. (Pic 4 5)
Click image for larger version

Name:	IMG_1487.jpg
Views:	845
Size:	37.0 KB
ID:	95833   Click image for larger version

Name:	IMG_1495.jpg
Views:	820
Size:	38.3 KB
ID:	95834   Click image for larger version

Name:	IMG_1488.jpg
Views:	802
Size:	33.0 KB
ID:	95836   Click image for larger version

Name:	IMG_1481.jpg
Views:	847
Size:	34.6 KB
ID:	95838   Click image for larger version

Name:	IMG_1482.jpg
Views:	804
Size:	46.1 KB
ID:	95841  


 
Reply With Quote
Old 01-22-2013, 01:29 AM   #4
itsme6582
 
itsme6582's Avatar
Recipes 
 
Nov 2009
Cleveland
Posts: 813
Liked 22 Times on 20 Posts


Nevermind. Nice job.

 
Reply With Quote
Old 01-22-2013, 01:36 AM   #5
matc
Recipes 
 
Aug 2006
Posts: 258
Liked 16 Times on 11 Posts


Couldn't you just plug the whole cooler in your stc-1000 instead ? Do you really have to mess with the built in thermostat ?

 
Reply With Quote
Old 01-22-2013, 01:40 AM   #6
aarong
 
aarong's Avatar
Recipes 
 
Jan 2012
Newport, RI
Posts: 212
Liked 20 Times on 17 Posts


7) Now attach the orange 1 gang low voltage bracket to the black thermostat/ light box on the fridge. I drilled a whole straight down from the black thermostat/light to the orange box. Then place the machine screw straight threw the hole and put a little bit of crazy glue on the head of the screw. You will have to attach the black thermostat/ light box on the fridge before you attach the orange box. There will be two screw posts hanging under the thermostat and two holes on top of the orange box(Pic 6, 7)

8) After a few minutes push the orange box onto the studs from the machine screw. Use the nuts to attach it to the fridge(Pic 8)

9) Now comes the fun part wiring! Drill a few holes on top of the hump in the back left corner of the fridge. I drilled 3 holes in the fridge. Two wires ran from the back of the fridge to the orange box. One ran from the back of the fridge to where the paint can heater is(I will describe how to build this late). Leave extra wire(better to have too much then too little)

10) The first step to wiring is taking one of the cords and using a sharpie to label wires. I took one of the wires one of the whites will be (green cold) one of the green wires will be black.

11) The numbers on top of the diagram are the outputs for the STC 1000. The wires coming in from the bottom is the wire that is plugged into the wall outlet. The middle is the back of the outlet.
Click image for larger version

Name:	IMG_1499.jpg
Views:	763
Size:	35.9 KB
ID:	95843   Click image for larger version

Name:	IMG_1502.jpg
Views:	766
Size:	28.5 KB
ID:	95844   Click image for larger version

Name:	IMG_1503.jpg
Views:	757
Size:	30.4 KB
ID:	95846   Click image for larger version

Name:	wiring.jpg
Views:	763
Size:	24.0 KB
ID:	95852   Click image for larger version

Name:	IMG_1505.jpg
Views:	762
Size:	42.5 KB
ID:	95854  


 
Reply With Quote
Old 01-22-2013, 01:42 AM   #7
aarong
 
aarong's Avatar
Recipes 
 
Jan 2012
Newport, RI
Posts: 212
Liked 20 Times on 17 Posts


Quote:
Originally Posted by matc View Post
Couldn't you just plug the whole cooler in your stc-1000 instead ? Do you really have to mess with the built in thermostat ?
No need to mess with the built in thermostat. I just wanted to remove it to attach the STC 1000 to it. I could of just glued it on under the thermostat but I wanted to use machine screws to make sure it wouldn't come off.

 
Reply With Quote
Old 01-22-2013, 01:44 AM   #8
dtfleming
 
dtfleming's Avatar
Recipes 
 
Feb 2012
Westminster, Maryland
Posts: 117
Liked 6 Times on 5 Posts


Bypassing the built in thermostat, allows you to drop the temp past 40 deg.

 
Reply With Quote
Old 01-22-2013, 01:50 AM   #9
aarong
 
aarong's Avatar
Recipes 
 
Jan 2012
Newport, RI
Posts: 212
Liked 20 Times on 17 Posts


12) So now the STC 1000 is wired so you can attach it to the face plate and to the orange box under the top of the fridge.

13) On to the outlet box. I took the blue one gang outlet box and cut out the circles to put the wires in the box. I then used two wood screws to attach it to the bottom left side of the fridge.

14) Using the wiring diagram I ran the wires from the STC-1000 to the back of the outlet and attached a seperate length of wire to the 15A plug. Then put the face plate on it. Make sure to remove the tab on the outlet to seperate the hot from cold.
Click image for larger version

Name:	IMG_1507.jpg
Views:	787
Size:	28.7 KB
ID:	95855   Click image for larger version

Name:	IMG_1511.jpg
Views:	738
Size:	28.9 KB
ID:	95856   Click image for larger version

Name:	IMG_1510.jpg
Views:	732
Size:	44.0 KB
ID:	95859   Click image for larger version

Name:	IMG_1512.jpg
Views:	734
Size:	32.6 KB
ID:	95860  

 
Reply With Quote
Old 01-22-2013, 01:51 AM   #10
aarong
 
aarong's Avatar
Recipes 
 
Jan 2012
Newport, RI
Posts: 212
Liked 20 Times on 17 Posts


Quote:
Originally Posted by dtfleming View Post
Bypassing the built in thermostat, allows you to drop the temp past 40 deg.
Correct

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Vissani Fermentation Chamber ingchr1 Fermenters 171 Yesterday 01:29 PM
Vissani MVWC52B kegerator conversion mcubed45 Kegerators & Keezers 13 05-15-2013 09:57 PM
Vissani 52 Wine Bottle Kegerator vkmaynard Bottling/Kegging 53 07-13-2012 02:10 AM
Vissani Kegerator Owners.... louballs Bottling/Kegging 2 07-12-2012 12:22 AM
Drilling holes in the top of Vissani Kegerator ok? musicawal Kegerators & Keezers 10 05-04-2012 04:52 PM


Forum Jump