First brew fear - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Beginners Beer Brewing Forum > First brew fear

Thread Tools
Old 01-16-2013, 09:41 PM   #1
Jan 2013
Posts: 5

Hello all,

I am new to the forum and brewing in general and have run into my first possible problem. I bought a wilkinson no boil kit and followed the instructions to the letter. So far, so good. However after 36 hours the airlock stopped bubbling and I fear the fermentation is stuck because of the temperature variation where I am storing the fermentor. I measured the temperature changes in the room and they go from 15C at night to about 22C when the heating is on. I know I can't be sure if it has stuck without an SG reading but since it is my first batch I don't want to run the risk of contamination. Is this temperature range acceptable or should I take a reading?

Thanks in advance

Reply With Quote
Old 01-16-2013, 09:44 PM   #2
Post Hoc Ergo Propter Hoc
Revvy's Avatar
Dec 2007
"Detroitish" Michigan
Posts: 40,936
Liked 3210 Times on 1894 Posts

Bubbling in primary SHOULD slow or stop eventually...Bubbling stopping or slowing down doesn't mean fermentation has stopped it ONLY means bubbling has. An airlock is a VENT, a VALVE for EXCESS CO2. It's not a magic fermentation gauge. When the majority of sugars are eaten in the initial burst of fermentation, lots of co2 is released. As it slows down, bubbling ceases or stops altogether because there's not as much EXCESS Co2 being released.

But that doesn't mean fermentation is over, just that it's slowed down.

Fermentation is not always dynamic...just because you don't SEE anything happening doesn't mean that the yeast aren't happily chewing away at whatever fermentables are in there....the only way to know comes from gravity readings, and nothing else.

Activity, action, bubbles, even krausen can be affected by the envoironment just as much as it being caused by the going by that is NOT reliable.

If you want to know what's going on with your beer, then take a gravity reading. The only way to truly know what is going on in your fermenter is with your hydrometer. Like I said here in my blog, which I encourage you to read, Think evaluation before action you sure as HELL wouldn't want a doctor to start cutting on you unless he used the proper diagnostic instuments like x-rays first, right? You wouldn't want him to just take a look in your eyes briefly and say "I'm cutting into your chest first thing in the morning." You would want them to use the right diagnostic tools before the slice and dice, right? You'd cry malpractice, I would hope, if they didn't say they were sending you for an MRI and other things before going in....

Counting bubbles does not equate to anything usable in fermentation. It's not like "x bubbles/minute= y gravity points." It just means that co2 is being released....but it could also NOT be bubbling, and still fermenting away.

Relax, leave your beer alone and let it do it's thing for a couple more weeks, and most importantly, IGNORE what your airlock does or doesn't do.
Like my snazzy new avatar? Get Sons of Zymurgy swag, here, and brew with the best.

Revvy's one of the cool reverends. He has a Harley and a t-shirt that says on the back "If you can read this, the bitch was Raptured. - Madman

I gotta tell ya, just between us girls, that Revvy is HOT. Very tall, gorgeous grey hair and a terrific smile. He's very good looking in person, with a charismatic personality... he drives like a ****ing maniac! - YooperBrew

Reply With Quote
Old 01-16-2013, 10:02 PM   #3
Jan 2013
Posts: 5

That's a good analogy. Thanks.

Pragmatically you think I should leave it for a couple of weeks then take reading with the hydrometer and take action if fermentation definitely hasn't taken place? Also what temperature range will the yeast be active at? Sorry for all the questions, I have looked around but thought to ask this knowledgable community first.

Reply With Quote
Thread Tools

Similar Threads
Thread Thread Starter Forum Replies Last Post
Batch Problems - fear of bad brew HBC General Beer Discussion 9 12-13-2012 08:05 PM
Second AG fear idover All Grain & Partial Mash Brewing 5 01-12-2012 04:24 AM
winter brew fermentation fear please help??? RIXBREW Extract Brewing 6 11-09-2010 06:48 PM
StarSan fear (rather, don't fear) Jebu1788 Equipment/Sanitation 13 10-05-2010 12:30 PM
Fear MeatyPortion Drunken Ramblings and Mindless Mumbling 8 06-26-2010 02:14 PM

Forum Jump