Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > Step 1: Cut a hole in the box. Step 2: Put your pump in the box.
Reply
 
Thread Tools
Old 01-14-2013, 02:34 PM   #1
TacoBrew
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2010
Location: Nashville, TN
Posts: 248
Liked 10 Times on 8 Posts
Likes Given: 4

Default Step 1: Cut a hole in the box. Step 2: Put your pump in the box.

Here are a few pictures of my attempt at a March pump toolbox conversion.

Power comes in from 25' extension cord and it powers my GFCI outlet. I decided not to alter the power cable on my pump, so it is plugged into a short extension cord and wired to the switch and outlet. I know the front switch isn't mounted beautifully, but that is a fix I can address at a later time.

The pump box is big enough to allow for a second pump on the opposite side as well as a second switch in the front. I have chosen a vertical mounting, though to be honest, I never had a problem with horizontal mounting.

For the box itself, I went with the Stanley 3-in-1 Rolling Workshop. The portability of this box is what I needed for my system. I run a two tier setup and some days I brew in the garage, some days in the yard and some days on the porch depending on weather. This wheeled assembly allows for great portability as well as ample storage. The base will probably be used to store tubing and I might bolt my plate chiller into it as well. The middle section is going to contain various brew day necessities and spare fittings. The top of course is the pump.

With this setup, I hope to be able to bring this box with me to other homebrewer's houses so that they can utilize the pump as long as they have a ball valve and a power outlet.


Click image for larger version

Name:	Pump Box Assembled.jpg
Views:	1075
Size:	45.3 KB
ID:	94337   Click image for larger version

Name:	Pump Box Outlet.jpg
Views:	1085
Size:	44.9 KB
ID:	94338   Click image for larger version

Name:	Pump Box Side View.jpg
Views:	1015
Size:	46.2 KB
ID:	94339   Click image for larger version

Name:	Pump Box Exploded.jpg
Views:	1018
Size:	59.9 KB
ID:	94340   Click image for larger version

Name:	Pump Box Outside.jpg
Views:	1014
Size:	62.8 KB
ID:	94341  

TacoBrew is offline
Jayhem Likes This 
Reply With Quote
Old 01-14-2013, 02:35 PM   #2
Jayhem
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2011
Location: Culpeper, VA
Posts: 2,639
Liked 277 Times on 224 Posts
Likes Given: 1252

Default

I see what you did there with the title.

Good stuff!


__________________
Next up: Amber Ale
Primary 1&2: 90 Min IPA clone
Primary 3&4: Belgian Wit
Keg #1: White Mosaic Pale Ale
Keg #2: Empty
Drinking: Amber Ale, White Mosaic Pale Ale
Jayhem is offline
 
Reply With Quote
Old 01-14-2013, 02:52 PM   #3
hot_carl
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2011
Location: Houston, TX
Posts: 112
Liked 3 Times on 3 Posts
Likes Given: 2

Default

Nice job...I like all of the toolbox/portable pump rigs that people have come up with. You mentioned having it portable so that you can utilize your pump with other brewers. Having an extra F type (male NPT and male cam) camlock in the toolbox will allow you to thread into any 1/2" ball valve. Different brewers use different fittings, so if that is part of the plan, its cheap insurance that you will always have compatibility. Have you had any issues with the pump heating up in the toolbox, or do you have some sort of ventilation for it? When I'm recirculating my mash for any period, the pumps do get a bit warm and they arent enclosed.
hot_carl is offline
 
Reply With Quote
Old 01-14-2013, 03:09 PM   #4
TacoBrew
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2010
Location: Nashville, TN
Posts: 248
Liked 10 Times on 8 Posts
Likes Given: 4

Default

Quote:
Originally Posted by hot_carl View Post
Nice job...I like all of the toolbox/portable pump rigs that people have come up with. You mentioned having it portable so that you can utilize your pump with other brewers. Having an extra F type (male NPT and male cam) camlock in the toolbox will allow you to thread into any 1/2" ball valve. Different brewers use different fittings, so if that is part of the plan, its cheap insurance that you will always have compatibility. Have you had any issues with the pump heating up in the toolbox, or do you have some sort of ventilation for it? When I'm recirculating my mash for any period, the pumps do get a bit warm and they arent enclosed.
That is my plan exactly. I'm just waiting for BrewHardware to open back up so I can order the extra fittings. As far as overheating, I haven't had a problem, but then again I haven't had to run it for any extended length of time. I don't have recirculation set up on my rig yet, so this is used only for transfer. If it does become an issue, though, it shouldn't be too difficult to splice in a fan.
TacoBrew is offline
 
Reply With Quote
Old 01-14-2013, 05:16 PM   #5
rekoob
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
rekoob's Avatar
Recipes 
 
Join Date: Feb 2011
Location: Norfolk, VA
Posts: 1,332
Liked 85 Times on 74 Posts
Likes Given: 11

Default

I had to read the thread just cuz of the title... very funny.

Nice build too.
rekoob is offline
BadNewsBrewery Likes This 
Reply With Quote
Old 01-14-2013, 11:29 PM   #6
chrislehr
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2010
Location: Austin
Posts: 358
Liked 10 Times on 9 Posts
Likes Given: 9

Default

Great looking build, but I have lots of questions
  • Total cost minus the $30 box and $110 pump and QD's?
  • Any plans to splash proof the outlets or switch any more?
  • Can you show an inside pic?
  • How much storage is available for other brew day goodies? I want to see it loaded up!
  • I wonder if mounting a self coiled cord thing inside the base would be feasible.. make clean/up break down a snap.

HBT shared you thread on FB - havent been here in a while

Thanks in advance.
__________________
I brewed all the beer at my wedding.
http://weddingbrewing.blogspot.com/
chrislehr is offline
 
Reply With Quote
Old 01-15-2013, 01:58 PM   #7
TacoBrew
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2010
Location: Nashville, TN
Posts: 248
Liked 10 Times on 8 Posts
Likes Given: 4

Default

Chrislehr, I haven't broken down the cost part by part yet but as a rough estimate:

Weather-resistant GFCI $15
Switch $1
1-gang box $2 (x2)
Light-duty extension cord $12
7" hose clamp $2.

Things I already had: outlet and switch face plates, 14 gauge wire, wire nuts, short extension cord that the pump is connected to internally so I didn't have to alter the factory power cord, two chunks of 2x4 that the pump is attached to with the clamp for support. And, actually, the pump was a prize from the Music City Brew Off raffle, so it was free!

I will get a picture of the inside when I'm home, but I am not an electrician by any means and didn't make it a priority for the wiring in the box to be clean.

I haven't decided what exactly is going to go in the storage areas yet, but there is ample room in the base to store all of my silicone tubing. My goal is to be able to roll this anywhere and have everything I need to use the pump self-contained in the box. I would like to mount my plate chiller to the base too, but I haven't worked out the logistics of that yet.

I considered adding something like a retracting cord and aside from potential space issues internally, sure, I don't see why not.
TacoBrew is offline
 
Reply With Quote
Old 01-15-2013, 06:34 PM   #8
CoalCracker
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
CoalCracker's Avatar
Recipes 
 
Join Date: Sep 2009
Location: Macungie, Pa
Posts: 1,659
Liked 104 Times on 64 Posts
Likes Given: 35

Default

Finally put your D!ck in a box!!

Nice job!
__________________
coalcrackerbrewing.blogspot.com
Vintage Kegerator Build
1 BBL Tippy Dump
CoalCracker is online now
 
Reply With Quote
Old 01-15-2013, 08:27 PM   #9
Homercidal
Licensed Sensual Massage Therapist.
HBT_MODERATOR.png
Feedback Score: 0 reviews
 
Homercidal's Avatar
Recipes 
 
Join Date: Feb 2008
Location: Reed City, MI
Posts: 27,067
Liked 3503 Times on 2393 Posts
Likes Given: 2308

Default

It's ok when it's in a 3-way. With a honey in the middle there some leeway. 2 Jack Trippers and a Chrissy is the new 3's company...


Oops, wrong Lonely Island song.
Homercidal is online now
 
Reply With Quote
Old 01-15-2013, 08:32 PM   #10
LittleCajunBrewery
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2013
Location: Asheville, North Carolina
Posts: 8
Default



LittleCajunBrewery is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Step by Step build a 110v portable PID controller Disintegr8or Electric Brewing 64 07-01-2015 09:10 AM
XXXXX's Whirlpool WAR349BSL Kegerator Conversion (37 picture step-by-step slideshow) XXXXX Kegerators and Keezers 32 08-24-2014 04:21 PM
Mashing Oats - Proper Temperature (2 step or single step) tmm0f5 Beginners Beer Brewing Forum 4 11-23-2011 08:46 PM
Hole Saw or step drill mrbugawkagawk Equipment/Sanitation 19 03-07-2010 02:43 PM
Step bit vs. hole saw... Discuss... Anthony_Lopez Equipment/Sanitation 43 05-09-2008 02:55 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS