Coldbreak Brewing Giveaway - Open to All!

Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > Propane plumbing help
Reply
 
Thread Tools
Old 12-06-2012, 05:21 AM   #1
mistercameron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2011
Location: SD, Ca
Posts: 433
Liked 15 Times on 11 Posts
Likes Given: 4

Default Propane plumbing help

I'm working out the plans for a single tier build and I have most of the propane plumbing figured out. The biggest question I have is about my particular regulator, which came as a Bayou Classic SP10. Keep in mind I'm trying to keep this budget tight so I can be wise with the money my wife is agreeing to let me spend on this hobby.

This is the actual part I have:
http://bayouclassicdepot.com/m5hpr_p..._regulator.htm
And the first part of the stand is going to be a 3/8" Tee so I can split off to each of the two burners.

#1: is 10PSI going to be enough to run two burners at once? So far I've been good with just one burner, so maybe this is a non-issue. My only thought was about mashing out the first batch sparge volume in the BK while warming water for the second batch.

#2: The orifice is built into the crimped swivel connection. My first thought is to just install a coupling between the orifice and the Tee (both 3/8). BUT, is it a problem that there is an orifice here and orifices downstream on the burners?

#2a: Am I just better off getting an adjustable regulator w/o the orifice, like this one? http://bayouclassicdepot.com/m5hpr1_..._regulator.htm (or an adjustable regulator?)



This is turning out to be a little bit trickier than I thought it would be. I've never dealt with propane plumbing before, so even figuring out the right combination of 1/4x3/8 fittings has been more work than I anticipated.

Thanks in advance for the help & insight!



Reason: Scrated #3. Figured it out.
mistercameron is offline
 
Reply With Quote
Old 12-06-2012, 01:25 PM   #2
jsmoon888
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: hanford, ca
Posts: 27
Liked 8 Times on 5 Posts

Default

I bought the adjustable one and run it at 20 psi. I used 3/8 copper tubing for the propane lines.


Click image for larger version

Name:	image-2351373267.jpg
Views:	728
Size:	44.0 KB
ID:	87153  
jsmoon888 is offline
 
Reply With Quote
Old 12-06-2012, 03:57 PM   #3
mistercameron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2011
Location: SD, Ca
Posts: 433
Liked 15 Times on 11 Posts
Likes Given: 4

Default

I'm digging the orange stand and diamond plate! What do you have to protect the paint from the burner heat?

It's kind of hard to tell, but are you running the copper from the BK under the lower tier's top rail? My concern would be that heat from a burner might be a bit too high on the supply line.

And finally, are you using soldered fittings or compression (is compression even an option in propane)?
mistercameron is offline
 
Reply With Quote
Old 12-06-2012, 04:39 PM   #4
mrrshotshot
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 7 reviews
 
mrrshotshot's Avatar
Recipes 
 
Join Date: Feb 2012
Location: Petaluma, CA
Posts: 648
Liked 43 Times on 39 Posts
Likes Given: 3

Default

Quote:
Originally Posted by jsmoon888 View Post
I bought the adjustable one and run it at 20 psi. I used 3/8 copper tubing for the propane lines.
Your stand and my stand should go on a date.

Click image for larger version

Name:	ForumRunner_20121206_083738.jpg
Views:	536
Size:	43.4 KB
ID:	87189

But in response to the OP it sounds like it shouldn't be a problem to go with what you are describing in either case. I would just make sure whatever you do should be spec'd out to the burners requirements. If it calls for a 20 psi regulator then use that.
mrrshotshot is offline
 
Reply With Quote
Old 12-06-2012, 05:50 PM   #5
mistercameron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2011
Location: SD, Ca
Posts: 433
Liked 15 Times on 11 Posts
Likes Given: 4

Default

Quote:
Originally Posted by mrrshotshot View Post
Your stand and my stand should go on a date.

Attachment 87189

But in response to the OP it sounds like it shouldn't be a problem to go with what you are describing in either case. I would just make sure whatever you do should be spec'd out to the burners requirements. If it calls for a 20 psi regulator then use that.
Bayou Classic isn't quite forthright with the BTU rating on the burner (it can operate anywhere from 10-40 PSI), but the Bayou regulator I already have says it supplies up to 55k BTU/h at 10psi. One thing I'm confused about is the needle valve attached to the reg says it's 1/2 PSI. Is it really reducing the line pressure to 1/2 PSI?

So does having a needle valve (wide open) upstream from the burner valves cause any problems?
mistercameron is offline
 
Reply With Quote
Old 12-06-2012, 09:03 PM   #6
mistercameron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2011
Location: SD, Ca
Posts: 433
Liked 15 Times on 11 Posts
Likes Given: 4

Default

Will "utility grade" copper coil be fine for this application?

http://www.lowes.com/pd_12605-69305-...ing&facetInfo=

or this?
http://www.homedepot.com/h_d1/N-25ec...1#.UMEIcKUWlNw
mistercameron is offline
 
Reply With Quote
Old 12-06-2012, 09:54 PM   #7
mrrshotshot
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 7 reviews
 
mrrshotshot's Avatar
Recipes 
 
Join Date: Feb 2012
Location: Petaluma, CA
Posts: 648
Liked 43 Times on 39 Posts
Likes Given: 3

Default

Not sure. I just used 3/8" flex propane hose. Much easier to work with. And probably cheaper too.
mrrshotshot is offline
 
Reply With Quote
Old 12-06-2012, 11:55 PM   #8
mistercameron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2011
Location: SD, Ca
Posts: 433
Liked 15 Times on 11 Posts
Likes Given: 4

Default

Quote:
Originally Posted by mrrshotshot View Post
Not sure. I just used 3/8" flex propane hose. Much easier to work with. And probably cheaper too.
Did you make your own? I called around and couldn't find anyone that would make custom lengths (or just buy short ones) for a reasonable price (eg, $15 for 15" hose). I have most of this stuff figured out, but there's one nagging question...

Can I screw the male flare into an FNPT fitting and get a good seal, or do I need to keep looking for a specialty fitting?
mistercameron is offline
 
Reply With Quote
Old 12-07-2012, 02:38 AM   #9
jsmoon888
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: hanford, ca
Posts: 27
Liked 8 Times on 5 Posts

Default

I used flare fittings on the copper tubing. Got the valves, orifices, burners and regulator from bayou. Got the manifold to tie it all together from McMaster. The top part of the orange paint is burnt to black now but it still looks ok.
jsmoon888 is offline
 
Reply With Quote
Old 12-07-2012, 03:53 AM   #10
mrrshotshot
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 7 reviews
 
mrrshotshot's Avatar
Recipes 
 
Join Date: Feb 2012
Location: Petaluma, CA
Posts: 648
Liked 43 Times on 39 Posts
Likes Given: 3

Default

I went to my local propane store and they sold me the lengths. I made them myself with some barbed flare fittings. It was 2$ a foot of gas line and I cant remember what the fittings cost.

But the flare fittings will not fit NPT. You'll have to get a 3/8 x 3/8 Flare coupler to make it work if you have it coming off of black iron pipe like i do.


mrrshotshot is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Help with propane plumbing Tomtanner Brew Stands 48 02-09-2013 09:34 PM
need propane plumbing help Dougie63 Brew Stands 1 05-19-2012 02:56 PM
Brewstand plumbing for propane - mr_cad Equipment/Sanitation 1 05-02-2011 11:03 PM
Plumbing Propane schultan Equipment/Sanitation 5 07-23-2008 07:53 PM
Propane plumbing alemonkey Brew Stands 6 12-29-2006 03:02 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS