Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > CFC copper tube size
Reply
 
Thread Tools
Old 08-24-2007, 03:01 AM   #1
Dr_Deathweed
Feedback Score: 0 reviews
 
Dr_Deathweed's Avatar
Recipes 
 
Join Date: Jul 2007
Location: Bryan, Texas
Posts: 2,407
Liked 28 Times on 22 Posts
Likes Given: 3

Default CFC copper tube size

I see that most of the CFC DIY use 25' 3/8" copper tubing. What about using 1/4" tubing? I am in a hot environment, and tap water doesn't get much below 80F in the summer, so my thoughts were smaller diameter tubing to increase the surface area to volume ratio, and use this for 50'

Besides, its $35 for 50' of 1/4" and $75 for 3/8"... I'm cheap....

My fluid dynamics is a little rusty, but I know the decreased diameter and increased length will decrease flow rate due to increased resistance, and the decreased diameter and flow will in turn lower the Reynolds number, leading to laminar flow. I know turbulent flow is desired, but I guess my questions are:

1. Am I missing something stupid and should stop thinking cheap
2. will the decrease in flow/increased surface area counteract the heat transfer limitations with laminar flow
3. if flow is a huge deal, what about running two 25' sections in parallel through the same hose
4. With a good filter in the boil pot, plugging shouldn't be an issue with a smaller diameter tubing. Right?


Dr_Deathweed is offline
 
Reply With Quote
Old 08-24-2007, 03:25 AM   #2
wwest
Feedback Score: 0 reviews
 
wwest's Avatar
Recipes 
 
Join Date: Jul 2007
Location: New Haven, CT
Posts: 71
Default

Seems like the answer to 2) would be tough to figure out, since there's a temp gradient along the length of the CFC (and therefore a viscosity and specific weight gradient)... and I guess you need to know those things if you care about ensuring turbulent flow.

I'd think about it some more but my girlfriend insists on going to bed or something.

__________________
On Deck: ???
Primary: Best Bitter
Lagering:
Carbonating:
Drinking: Apfelwein, IPA, Jalapeno Ale
wwest is offline
 
Reply With Quote
Old 08-24-2007, 11:48 AM   #3
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
Vendor Ads 
Feedback Score: 3 reviews
 
Bobby_M's Avatar
Recipes 
 
Join Date: Aug 2006
Location: Whitehouse Station, NJ
Posts: 22,550
Liked 1214 Times on 798 Posts
Likes Given: 29

Default

Look at it this way; You can't speed up the flow through a restrictive diameter but you can slow down flow on a larger one. I can tell you that a gravity drain though even 3/8" OD x 25' is pretty slow already. You don't need 50', it's overkill.

I have to run really slow when the tap is 70+. When it's 55F in the winter, I actually have to restrict my tap flow or wort comes out at 60F.
__________________
Welcome to BrewHardware.com. I love you.
New 100% Stainless Steel Heating Elements are IN! ULWD 5500w Ripple, 2000w, 1500w, etc
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.
Bobby_M is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Copper tube types runhard Equipment/Sanitation 6 12-18-2010 11:30 PM
Copper Tube Source HenryHill Equipment/Sanitation 2 11-22-2007 03:37 AM
SS braid, copper tube, bazooka tube??? Joetuo Equipment/Sanitation 12 10-26-2007 01:58 AM
Wort Chiller Copper tube size javedian Chillers and Stir Plates 29 03-12-2007 07:53 PM
Copper tube matc07098702 Bottling/Kegging 3 06-03-2005 05:12 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS