Help with brewing water in SW Florida - Page 2 - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Brew Science > Help with brewing water in SW Florida

Reply
 
Thread Tools
Old 12-08-2012, 11:45 PM   #11
ajdelange
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Aug 2010
McLean/Ogden, Virginia/Quebec
Posts: 9,297
Liked 1494 Times on 1141 Posts


Quote:
Originally Posted by kifkroker View Post
My RO system is an 8 year old, 3-stage Watershield RO System. It has a pre carbon filter, post carbon filter, RO membrane, 100 psi permeate pump and 3 gal holding tank with bladder.
Are you sure the pump isn't before the membrane i.e. on the feed side? There wouldn't be much point in having it on the permeate side.

Quote:
Originally Posted by kifkroker View Post
Should I purchase a new RO system or just replace the membrane on my current 8 year old system? I change the filters on schedule but haven't changed the membrane for about 3 years so I know the high TDS is my fault.
I don't see any reason to not stay with what you have unless you find it hard to obtain a cartridge for the old system.

Quote:
Originally Posted by kifkroker View Post
Also, any benefit from adding a whole house filter to filter the water before it comes into the house? Will that ease the burden on the RO system?
If the water is stinky (and you say it is) then a whole house filter will help get rid of that making the job of the pre-filter on the RO unit a bit easier and those cartridges will last longer.

 
Reply With Quote
Old 12-09-2012, 07:07 PM   #12
grathan
Recipes 
 
Jul 2010
Albany, NY
Posts: 2,250
Liked 146 Times on 115 Posts


membrane, unless the new one gives you under a year before starting to clog. Then I would way the cost of just buying membranes vs. adding more filters or perhaps changing the size of the pre-filter. Most of the new systems I looked at had either a 1 micron or a .5 micron filter or a series of 5 micron and then a 1 micron before the membrane.

 
Reply With Quote
Old 12-27-2012, 01:50 AM   #13
kifkroker
Recipes 
 
May 2012
Sarasota, FL
Posts: 67
Liked 4 Times on 4 Posts


Ok... It has been a couple weeks since I replaced both pre & post filters (5 micron KX Matrikx CTO/2) and also the membrane (GE Osmonics Desal TFM-36 GPD). Over the last week, I have checked the TDS periodically and it has ranged from 96 to 134. At this point, should I continue troubleshooting my RO & water softener system or just accept that my water is too hard for RO to filter to a tolerable range to brew with?

Again... any help or suggestions are greatly appreciated. Thanks!

 
Reply With Quote
Old 12-27-2012, 02:25 PM   #14
ajdelange
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Aug 2010
McLean/Ogden, Virginia/Quebec
Posts: 9,297
Liked 1494 Times on 1141 Posts


With a feed TDS of about 1000 a permeate TDS of about 100 suggests only 90% average rejection. I'd expect better of a new membrane so I suspect there may be leakage around it. Check the O-rings in the system following the manufacturer's instructions.

If, OTOH, the surge in output TDS is related to a surge in feed TDS then, yes, you will have to accept the fact that you have real problem water. A solution, used in places in the world where they brew with sea or brackish water, is to use two RO systems in tandem. If each is only capable of average rejection of 95% (50 ppm out for 1000 ppm in) the pair will give better than 99% rejection (2.5 ppm out of the second system if the first has 1000 coming in). You will need to figure out some way to interconnect the two such that the pressure into the second is high enough to operate it.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Florida Water? ctbrewer227 Beginners Beer Brewing Forum 15 08-14-2013 06:26 PM
$1500 water bill in Florida BrokenArmBrewing General Chit Chat 66 06-15-2013 01:51 AM
Jacksonville Florida water Newmanwell Brew Science 5 01-12-2013 05:07 AM
Water Filtration in Hillsborough County Florida Chris7687 Equipment/Sanitation 0 10-18-2012 02:07 PM


Forum Jump