Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > Automated Brewing Forum > Volume Measurement Dipstick
Reply
 
Thread Tools
Old 11-19-2012, 04:14 PM   #1
gnatp2
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2009
Location: Hoboken
Posts: 103
Liked 1 Times on 1 Posts
Likes Given: 1

Default Volume Measurement Dipstick

Anyone have a good way of securing a 1/4" stainless dip tube for volume measurement in a kettle? (via Brewtroller and MPX5010DP). I've seen some in a keggle that look decent but not in a kettle with straight sides. I'd like to have mine more secure to prevent any potential moving around during the brew process.

The top would be easy to secure with something like a 1/4" compression fitting near the top of the side wall, but I don't know how to anchor the bottom.

Nate


gnatp2 is offline
 
Reply With Quote
Old 11-19-2012, 04:19 PM   #2
Jayhem
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2011
Location: Culpeper, VA
Posts: 2,639
Liked 277 Times on 224 Posts
Likes Given: 1250

Default

I use a hardwood wooden rod that I attach down the inside wall of the kettle on brew day with a small C-clamp at the top, perfectly stable. It only needs to be in the pot when pouring in mash and sparge water to check volumes and then I just leave it out until I'm nearing my boil time to check final post-boil volume. Not sure why you would want/need one permanently attached.


__________________
Next up: Amber Ale
Primary 1&2: 90 Min IPA clone
Primary 3&4: Belgian Wit
Keg #1: White Mosaic Pale Ale
Keg #2: Empty
Drinking: Amber Ale, White Mosaic Pale Ale
Jayhem is offline
 
Reply With Quote
Old 11-19-2012, 04:46 PM   #3
gnatp2
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2009
Location: Hoboken
Posts: 103
Liked 1 Times on 1 Posts
Likes Given: 1

Default

Quote:
Originally Posted by Jayhem View Post
I use a hardwood wooden rod that I attach down the inside wall of the kettle on brew day with a small C-clamp at the top, perfectly stable. It only needs to be in the pot when pouring in mash and sparge water to check volumes and then I just leave it out until I'm nearing my boil time to check final post-boil volume. Not sure why you would want/need one permanently attached.
I would prefer permanently mounted because otherwise it is just one more thing to setup during brewday. Also, I would like to be able to put on a lid and this would stick out of the top.
gnatp2 is offline
 
Reply With Quote
Old 11-19-2012, 04:54 PM   #4
oakbarn
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
oakbarn's Avatar
Recipes 
 
Join Date: Jun 2011
Location: Argyle, Texas
Posts: 761
Liked 51 Times on 40 Posts
Likes Given: 26

Default

I use my Mash Paddle. I know the apx volume by the holes and handle. I used to use a hardwood stick as well but now use the paddle and thermowells for my apx volume. I always add a little water by sight as I try to be on the dry side when I fist add the grain. Same with batch sparge. I know what I want it to look like and to me that is part of the process. I do make the same beers over and over and generally get very close OG each time for my brew.

I had purchased a scale that is under the MLT but I found that the paddle and sight process much easier and better. I do not use the scale anymore.
oakbarn is offline
 
Reply With Quote
Old 11-19-2012, 05:00 PM   #5
Jayhem
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2011
Location: Culpeper, VA
Posts: 2,639
Liked 277 Times on 224 Posts
Likes Given: 1250

Default

Quote:
Originally Posted by gnatp2 View Post
I would prefer permanently mounted because otherwise it is just one more thing to setup during brewday. Also, I would like to be able to put on a lid and this would stick out of the top.
That makes sense, just seems like a cleaning nightmare to have permanent fixtures in a brew kettle.
__________________
Next up: Amber Ale
Primary 1&2: 90 Min IPA clone
Primary 3&4: Belgian Wit
Keg #1: White Mosaic Pale Ale
Keg #2: Empty
Drinking: Amber Ale, White Mosaic Pale Ale
Jayhem is offline
 
Reply With Quote
Old 11-19-2012, 05:02 PM   #6
Golddiggie
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
Golddiggie's Avatar
Recipes 
 
Join Date: Dec 2010
Location: Between here and there, and everywhere
Posts: 12,063
Liked 483 Times on 423 Posts
Likes Given: 266

Default

Will you be sending something down into the tube? IF not, I would seriously look into making/getting a sight tube that goes on the outside of the kettle. You can get (or make, as I did) one that connects back into the kettle at both the low and high points.

If you do want to send something down into the tube, then you could still make it external to the kettle. Just means you'll use stainless tubing instead of [borosilicate] glass (or polycarbonate). My only concern with having an open top is the potential to have either boiling wort shoot out (if you don't shield it low) or something fall in (more important during the chill phase).
__________________
Hopping Tango Brewery

跟猴子比丟屎 ・ Gun HOE-tze bee DIO-se

On Tap: Caramel Ale, Mocha Porter II, MO SMaSH IPA
Waiting/Carbonating: 12.5% Wee Honey II, 8.9% Old Ale, English Brown Ale, Lickah ESB, Mocha Porter II
Fermenting
K1:
K2: Epic mead
K3: TripSix
On Deck: Caramel Ale
Aging:mead
Mead [bottled]:Oaked Wildflower Traditional, Mocha Madness, Blackberry Melomel, maple wine
Golddiggie is offline
 
Reply With Quote
Old 11-19-2012, 05:22 PM   #7
gnatp2
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2009
Location: Hoboken
Posts: 103
Liked 1 Times on 1 Posts
Likes Given: 1

Default

Quote:
Originally Posted by Golddiggie View Post
Will you be sending something down into the tube? IF not, I would seriously look into making/getting a sight tube that goes on the outside of the kettle. You can get (or make, as I did) one that connects back into the kettle at both the low and high points.

If you do want to send something down into the tube, then you could still make it external to the kettle. Just means you'll use stainless tubing instead of [borosilicate] glass (or polycarbonate). My only concern with having an open top is the potential to have either boiling wort shoot out (if you don't shield it low) or something fall in (more important during the chill phase).
The only thing I plan on putting down the tube is air from an airpump.

Got any pics of it? That's kinda what I was thinking, but i don't know how to get the tube low enough in the tank for it get good low volume readings.
gnatp2 is offline
 
Reply With Quote
Old 11-19-2012, 05:38 PM   #8
Golddiggie
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
Golddiggie's Avatar
Recipes 
 
Join Date: Dec 2010
Location: Between here and there, and everywhere
Posts: 12,063
Liked 483 Times on 423 Posts
Likes Given: 266

Default

Quote:
Originally Posted by gnatp2 View Post
The only thing I plan on putting down the tube is air from an airpump.

Got any pics of it? That's kinda what I was thinking, but i don't know how to get the tube low enough in the tank for it get good low volume readings.
These are pictures of ones I've made so far...

No weld:


Welded


If you're using air, then you could do the no weld version and just add a fitting inside to go to the air source. Depending on the kettle you're using, you could get pretty low. Just be sure to have a shield under the lower fitting to prevent it from boiling inside (I've had that happen, doesn't when I have a metal shield under it).

If you want to brainstorm more, PM me and we'll communicate outside the boards.


__________________
Hopping Tango Brewery

跟猴子比丟屎 ・ Gun HOE-tze bee DIO-se

On Tap: Caramel Ale, Mocha Porter II, MO SMaSH IPA
Waiting/Carbonating: 12.5% Wee Honey II, 8.9% Old Ale, English Brown Ale, Lickah ESB, Mocha Porter II
Fermenting
K1:
K2: Epic mead
K3: TripSix
On Deck: Caramel Ale
Aging:mead
Mead [bottled]:Oaked Wildflower Traditional, Mocha Madness, Blackberry Melomel, maple wine
Golddiggie is offline
Jayhem Likes This 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Bubbler Volume Measurement moparx12 Other 5 02-18-2012 02:51 PM
Brew Pot Dipstick just2brew Kettles, Mash Tuns, & Hot Liquor Tanks 2 03-20-2011 10:20 PM
Water Volume Measurement TheCrowsNest Equipment/Sanitation 1 01-05-2011 12:23 AM
Strike Volume Measurement JamieT Other 14 08-23-2009 04:20 AM
volume vs. weight measurement Mogref Beginners Beer Brewing Forum 7 03-31-2009 01:43 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS