Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Regulator slowly rises in pressure?
Reply
 
Thread Tools
Old 10-21-2012, 12:31 PM   #1
sbb
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2011
Location: , SC
Posts: 12
Default Regulator slowly rises in pressure?

Hey guys... I've got a dual body regulator. I used the second regulator to force carb a beer, and afterwards it wont hold a pressure steady. it slowly rises by about 1 psi in 10 seconds. Even with the regulator turned off! Both the tank and regulators are in the kegerator because it is in the garage and it gets really hot here in the summer. Any thought? Maybe a rebuild kit?


sbb is offline
 
Reply With Quote
Old 10-21-2012, 01:06 PM   #2
MalFet
/bɪər nɜrd/
HBT_LIFETIMESUPPORTER.png
Feedback Score: 1 reviews
 
MalFet's Avatar
Recipes 
 
Join Date: May 2010
Location: NYC / Kathmandu
Posts: 8,464
Liked 1389 Times on 921 Posts
Likes Given: 665

Default

Hmm... I'm not sure i understand. It rises continuously by 1psi per 10 seconds? Or it just bumps up by a single psi once? In either case, rises relative to what? When does it start rising?


__________________
"Be excellent to each other." -Benjamin Franklin
MalFet is online now
 
Reply With Quote
Old 10-21-2012, 01:17 PM   #3
sbb
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2011
Location: , SC
Posts: 12
Default

Sorry... So the regulator is completely off (unscrewed the adjuster). Yet the gauge will slowly rise in pressure. And there is co2 leaving the gauge. Is that more clear?
sbb is offline
 
Reply With Quote
Old 10-21-2012, 01:22 PM   #4
Yooper
Ale's What Cures You!
HBT_ADMIN.png
Feedback Score: 0 reviews
 
Yooper's Avatar
Recipes 
 
Join Date: Jun 2006
Location: UP of Michigan
Posts: 65,868
Liked 6199 Times on 4414 Posts
Likes Given: 1645

Default

Quote:
Originally Posted by sbb View Post
Sorry... So the regulator is completely off (unscrewed the adjuster). Yet the gauge will slowly rise in pressure. And there is co2 leaving the gauge. Is that more clear?
It's hooked up to the beer? If so, it means your beer is higher than the pressure you are trying to hold.

It sounds like your beer must have been at a higher pressure at some point, and is overcarbed, and your regulator is turned lower than that pressure.
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

Follow me on facebook: https://www.facebook.com/lorena.t.evans
But I'm pretty boring so don't expect much!
https://www.facebook.com/lorena.t.evans
Yooper is offline
 
Reply With Quote
Old 10-21-2012, 01:31 PM   #5
sbb
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2011
Location: , SC
Posts: 12
Default

Sorry, I'm doing a terrible job at explaining this.

Beer isn't hooked up. There is a hose connected to this problematic regulator with a pin lock connector on the other end. Valve is completely off (unscrewed til it's very loose), yet the pressure as read on the guage will rise from zero to well over 45psi over time. And there is pressure (not just a guage issue), as verified at the pin-lock connector by pushing the thing that pushes the poppet valve (gas escaped). Also the same can be seen by pulling the pressure release valve in this specific regulator body.
sbb is offline
 
Reply With Quote
Old 10-21-2012, 01:41 PM   #6
JohnnyO
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
JohnnyO's Avatar
Recipes 
 
Join Date: Dec 2008
Location: Hamden, CT
Posts: 8,940
Liked 909 Times on 852 Posts
Likes Given: 524

Default

Quote:
Originally Posted by sbb
Sorry, I'm doing a terrible job at explaining this.

Beer isn't hooked up. There is a hose connected to this problematic regulator with a pin lock connector on the other end. Valve is completely off (unscrewed til it's very loose), yet the pressure as read on the guage will rise from zero to well over 45psi over time. And there is pressure (not just a guage issue), as verified at the pin-lock connector by pushing the thing that pushes the poppet valve (gas escaped). Also the same can be seen by pulling the pressure release valve in this specific regulator body.
Sounds like it might be a bad diaphragm in the regulator. It will allow more pressure to bleed through than intended. There is a repair kit available to fix this pretty cheap.
__________________
Fermenting: Festbier, Saison, hefeweizen, American Wheat
Drinking: Bananas Foster Hefeweizen, IPA
On Deck: Milk Stout / Scotch Ale
JohnnyO is offline
 
Reply With Quote
Old 10-21-2012, 01:47 PM   #7
sbb
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2011
Location: , SC
Posts: 12
Default

Quote:
Originally Posted by JohnnyO View Post
Sounds like it might be a bad diaphragm in the regulator. It will allow more pressure to bleed through than intended. There is a repair kit available to fix this pretty cheap.
I kinda thought this was the case. Are these repair kits specific to the brand of the regulator? Or are they fairly generic?
sbb is offline
 
Reply With Quote
Old 10-21-2012, 01:57 PM   #8
lschiavo
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
lschiavo's Avatar
Recipes 
 
Join Date: Sep 2009
Location: Surrounded by Yoopers
Posts: 4,367
Liked 942 Times on 632 Posts
Likes Given: 774

Default

You will need a kit for your specific regulator.

I had a similar problem with mine. It turned out to not be the diaphragm but a loose valve seat. The seat is brass pressed into the regulator body. I just tapped it back in and it solved my problem. I'll post the link to my thread in a bit...

http://www.homebrewtalk.com/f35/help...ulator-193608/
lschiavo is offline
 
Reply With Quote
Old 10-21-2012, 02:00 PM   #9
MalFet
/bɪər nɜrd/
HBT_LIFETIMESUPPORTER.png
Feedback Score: 1 reviews
 
MalFet's Avatar
Recipes 
 
Join Date: May 2010
Location: NYC / Kathmandu
Posts: 8,464
Liked 1389 Times on 921 Posts
Likes Given: 665

Default

Quote:
Originally Posted by sbb View Post
Sorry, I'm doing a terrible job at explaining this.

Beer isn't hooked up. There is a hose connected to this problematic regulator with a pin lock connector on the other end. Valve is completely off (unscrewed til it's very loose), yet the pressure as read on the guage will rise from zero to well over 45psi over time. And there is pressure (not just a guage issue), as verified at the pin-lock connector by pushing the thing that pushes the poppet valve (gas escaped). Also the same can be seen by pulling the pressure release valve in this specific regulator body.
Ah, gotcha. Yeah, to concur with Johnny O, sounds like a bad diaphragm. The brand does matter sometimes, though many regulators use similar parts.
__________________
"Be excellent to each other." -Benjamin Franklin
MalFet is online now
 
Reply With Quote
Old 10-21-2012, 04:34 PM   #10
OntarioBeerKegs
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2009
Location: Mitchell, Ontario
Posts: 627
Liked 41 Times on 30 Posts
Likes Given: 7

Default

Before you go spending money try burst blasting the offending regulator by turning it up all the way and bursting co2 through a unobstructed (hoses removed and open) outlet a few seconds a few times. If that does not work open it clean the diaphragm and inspect for rough edges that can be fixed. Lubed.


OntarioBeerKegs is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Slant media rises under pressure??? Mpavlik22 Fermentation & Yeast 4 01-24-2012 11:11 PM
CO2 Pressure slowly dropping flabyboy Bottling/Kegging 6 08-03-2011 04:04 PM
WTB: Wall Mount 3 Pressure CO2 regulator with high pressure line kuips Bottling/Kegging 10 03-04-2010 11:25 PM
Slowly falling keg-side pressure? NonServiam Bottling/Kegging 7 07-17-2009 04:03 PM
co2 regulator slowly drifting up EeryBug Bottling/Kegging 1 04-30-2008 02:44 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS