Liquid post leak - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Liquid post leak

Reply
 
Thread Tools
Old 10-19-2012, 04:35 AM   #1
Ttownbrewer
Recipes 
 
Jan 2012
Thornton, CO
Posts: 149
Liked 5 Times on 5 Posts



First time kegging, force carbed for 2 weeks no liquid hooked up. Went down the other day to check it out, tapped the ball lock to the liquid side, and set the co2 to serving pressure. All was good with carbonation, etc.... Until, there was a puddle of beer on the floor.

Seems to be leaking underneath the post. Is there a way to fix temporarily, or is the keg pretty much done? I just bought them, and the shop said they were good. Guess I should of checked for leaks before filling.

Anybody got any ideas?

 
Reply With Quote
Old 10-19-2012, 05:02 AM   #2
DanH
Recipes 
 
Jun 2012
Posts: 1,026
Liked 83 Times on 65 Posts


Well if it didn't leak before you hooked up the liquid disconnect, then I would say the post and o rings must be ok. It sounds like it would be the disconnect. Do you have another one to try?

 
Reply With Quote
Old 10-19-2012, 05:09 AM   #3
Ttownbrewer
Recipes 
 
Jan 2012
Thornton, CO
Posts: 149
Liked 5 Times on 5 Posts


Quote:
Originally Posted by DanH
Well if it didn't leak before you hooked up the liquid disconnect, then I would say the post and o rings must be ok. It sounds like it would be the disconnect. Do you have another one to try?
I hooked up 3 different disconnects, same result each time.. It's leaking from where the post comes out of the dip tube, under the hex that tightens.

I can take some pictures to post if that helps to explain it.

 
Reply With Quote
Old 10-19-2012, 11:57 AM   #4
zachattack
Recipes 
 
Mar 2012
, MA
Posts: 2,768
Liked 299 Times on 252 Posts


But it's not leaking if there's no quick disconnect installed? I think that's the confusing part, the dip tube / post / poppet is under pressure regardless of whether or not the QD is attached. So if it's leaking then, it should be always leaking.

Either way you can fix this and the beer will be fine, no worries. As a first shot I'd try tightening the post a little more (don't overdo it, there's an o-ring in there). If that doesn't work I'd release the pressure on the keg, undo the post and replace the dip tube o-ring.

 
Reply With Quote
Old 10-19-2012, 01:52 PM   #5
DanH
Recipes 
 
Jun 2012
Posts: 1,026
Liked 83 Times on 65 Posts


I had a poppet that was the wrong size once and lot made the QD fit incorrectly. Does yours snap down onto the post correctly?

Aunt_Ester Likes This 
Reply With Quote
Old 10-19-2012, 02:33 PM   #6
Ttownbrewer
Recipes 
 
Jan 2012
Thornton, CO
Posts: 149
Liked 5 Times on 5 Posts


Everything fits correctly. I'm going to run by the LHBS today and grab a couple more QD's, and o rings just in case I have to tear it apart! Let you know if it works.

Thanks guys for your input, I appreciate it!

 
Reply With Quote
Old 10-19-2012, 04:02 PM   #7
DanH
Recipes 
 
Jun 2012
Posts: 1,026
Liked 83 Times on 65 Posts


Take the keg with you. They can diagnose/repair.

 
Reply With Quote
Old 10-21-2012, 07:04 PM   #8
Ttownbrewer
Recipes 
 
Jan 2012
Thornton, CO
Posts: 149
Liked 5 Times on 5 Posts


Turned out the o ring on the dip tube was the culprit. Changed that out, and its all good. A learning experience for sure. Thanks guys for leading me the right direction!

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
New liquid leak in Corny when under pressure ZeeSniper Bottling/Kegging 10 07-30-2012 11:18 PM
Liquid Disconnect Leak slcdawg Beginners Beer Brewing Forum 9 07-27-2012 01:24 PM
Slow Leak on Keg at the Out (liquid) Post msmith92 Bottling/Kegging 4 04-06-2012 09:00 PM
Liquid out leak? OrangeOak Bottling/Kegging 13 11-11-2011 01:30 PM
Liquid side leak bigolbigbelly Bottling/Kegging 4 12-17-2009 05:40 PM


Forum Jump