False Bottom Issue - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > False Bottom Issue
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 09-17-2012, 05:36 PM   #1
1stTimer
Recipes 
 
Jan 2009
Salisbury, Maryland
Posts: 741
Liked 7 Times on 7 Posts



Yes I did post this in another thread. I would not double post if it weren't time sensitive. I am out shopping around for materials right now.

Ok, so I finally gave in and got a nice false bottom for my mlt. I was so excited to finally use it 2 weeks ago. Everything was going great in the brewing until the stuck sparge from HELL!! I had never had a stuck sparge period, let alone this beast of one. I ended up having to dump my mlt out completely and switch the false bottom out for the old braid. After some research it turns out I was not using the correct type of hose to run from the fb to the inside of the spigot. I was using a basic hose that you use to drain the tun.

So my question is this, what type of hose should I be using and where can I find it? Ideally I would use copper or cpvc but I am brewing Friday and the hose just seems like the easiest and quickest solution. Or if anyone can refer to a page on how to make a copper or cpvc connection that would be great as well. Iím not the handiest of people and donít have a lot of tools at my disposal.

Thanks as always fellow brewers. CHEERS!


__________________
ATOMIC DONKEY BREWING
http://atomicdonkeybrewing.blogspot.com
Primary:
Secondary: Black RyePA, Sour
Currently in Bottles: Zaporter part deux, Black Betty Oaked Bourbon Porter
Currently in Kegs: Donkey Milk Stout, Galaxy IPA

 
Reply With Quote
Old 09-17-2012, 05:45 PM   #2
cooper
Recipes 
 
Dec 2009
OFallon, IL
Posts: 467
Liked 28 Times on 25 Posts


That sux! Have you checked out the high temperature hose they have at Lowes? You know the kind with the braiding inside of it and it's rigid as hell? That's the only thing I can think of using that you wont have to measure and cut and fit...



 
Reply With Quote
Old 09-17-2012, 05:48 PM   #3
1stTimer
Recipes 
 
Jan 2009
Salisbury, Maryland
Posts: 741
Liked 7 Times on 7 Posts


Thats what I was thinking. My only concern with it will be clamping it down tight. This stuff is thick as hell. Im all for using copper as a long term solution. The hose can be temporary just for this weekend. Need to find a nice "how to" page for the copper. I dont have the tools but know plenty of folks that do. Its good to know people.
__________________
ATOMIC DONKEY BREWING
http://atomicdonkeybrewing.blogspot.com
Primary:
Secondary: Black RyePA, Sour
Currently in Bottles: Zaporter part deux, Black Betty Oaked Bourbon Porter
Currently in Kegs: Donkey Milk Stout, Galaxy IPA

 
Reply With Quote
Old 09-17-2012, 06:57 PM   #4
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 22,978
Liked 1584 Times on 1021 Posts


It's important to know what you have now. How about a picture?
__________________
Welcome to BrewHardware.com. I love you.
BIAB Large Mesh False Bottoms and SS HERMS COILS are IN!!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 09-17-2012, 07:03 PM   #5
1stTimer
Recipes 
 
Jan 2009
Salisbury, Maryland
Posts: 741
Liked 7 Times on 7 Posts


As far as the tubing or the false bottom and spigot?
__________________
ATOMIC DONKEY BREWING
http://atomicdonkeybrewing.blogspot.com
Primary:
Secondary: Black RyePA, Sour
Currently in Bottles: Zaporter part deux, Black Betty Oaked Bourbon Porter
Currently in Kegs: Donkey Milk Stout, Galaxy IPA

 
Reply With Quote
Old 09-17-2012, 07:13 PM   #6
audger
Recipes 
 
Apr 2011
., Connecticut
Posts: 1,497
Liked 43 Times on 42 Posts


you are talking about the hose that connects from a fitting/barb in the center of a rigid screen false bottom to the valve on the side of the pot, yes? use a nice piece of silicone hose. i have 3/8" barbs on both my false bottom and the inside of the exit valve, and connect them with a nice piece of silicone. no need for clamping or anything (as long as you you remember where it is and are careful with your stirring!).

 
Reply With Quote
Old 09-17-2012, 07:31 PM   #7
1stTimer
Recipes 
 
Jan 2009
Salisbury, Maryland
Posts: 741
Liked 7 Times on 7 Posts


Yes. That exactly what I'm talking about. The silicone works well it sounds like. I wasn't sure if it would cause off flavors or anything. Where did you picked it up? Home depot or somewhere like that? Someone has been very generous in offering me some but I'm extremely impatient when it comes to brewing. If I could run up the road 5 mins after work and get some I will.
__________________
ATOMIC DONKEY BREWING
http://atomicdonkeybrewing.blogspot.com
Primary:
Secondary: Black RyePA, Sour
Currently in Bottles: Zaporter part deux, Black Betty Oaked Bourbon Porter
Currently in Kegs: Donkey Milk Stout, Galaxy IPA

 
Reply With Quote
Old 09-17-2012, 07:37 PM   #8
1stTimer
Recipes 
 
Jan 2009
Salisbury, Maryland
Posts: 741
Liked 7 Times on 7 Posts


On that note, have you had trouble keeping the falso bottom from floating while mixing in your grains? Im not sure if that was an issue last time or not for me. i couldnt tell because the damn cheap tubing I was using collapsed so quickly.
__________________
ATOMIC DONKEY BREWING
http://atomicdonkeybrewing.blogspot.com
Primary:
Secondary: Black RyePA, Sour
Currently in Bottles: Zaporter part deux, Black Betty Oaked Bourbon Porter
Currently in Kegs: Donkey Milk Stout, Galaxy IPA

 
Reply With Quote
Old 09-18-2012, 05:16 PM   #9
cooper
Recipes 
 
Dec 2009
OFallon, IL
Posts: 467
Liked 28 Times on 25 Posts


Quote:
Originally Posted by 1stTimer View Post
On that note, have you had trouble keeping the falso bottom from floating while mixing in your grains? Im not sure if that was an issue last time or not for me. i couldnt tell because the damn cheap tubing I was using collapsed so quickly.
Here is a recommendation from Jhall4 in another thread:

"As long as it's properly fitted into the tank the grain will hold it down and do all the work for you. If you're getting a gap around the edges, just take some high temp tubing, cut it open along one side to make a gasket, and fit it around the FB - should seal up nice and tight! "

Sounds like good advice.

 
Reply With Quote
Old 09-18-2012, 05:27 PM   #10
jhall4
Recipes 
 
Aug 2012
Pleasanton, California
Posts: 151
Liked 13 Times on 12 Posts


Quote:
Originally Posted by cooper View Post
Here is a recommendation from Jhall4 in another thread:

"As long as it's properly fitted into the tank the grain will hold it down and do all the work for you. If you're getting a gap around the edges, just take some high temp tubing, cut it open along one side to make a gasket, and fit it around the FB - should seal up nice and tight! "

Sounds like good advice.
haha, I just saw this thread about FBs and was going to offer the same advice!



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
How to force plastic false bottom to bottom of mashtun alfista Equipment/Sanitation 3 06-26-2012 07:12 PM
Center Pickup w/ False Bottom or Side Pickup w/o False Bottom craigsphillips Equipment/Sanitation 14 01-22-2012 05:22 PM
Issue with false bottom in MLT on first use - should I switch to braided hose? Rev2010 Equipment/Sanitation 4 10-31-2011 11:15 PM
Keggle/SS false bottom issue LouBrew2 Equipment/Sanitation 4 01-26-2011 08:36 PM
Pickup location from bottom on false bottom Darboy Equipment/Sanitation 1 03-01-2009 07:58 PM


Forum Jump