Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Doing my first AG tomorrow an Amber Ale
Reply
 
Thread Tools
Old 08-31-2012, 10:34 PM   #1
NateG
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2011
Location: Keizer, Oregon
Posts: 123
Liked 6 Times on 5 Posts

Default Doing my first AG tomorrow an Amber Ale

I went down to the local homebrew shop today and purchased my grains ect for my first all grain. I am "copying" Northern Brewers American amber which I have done as an extract kit before. I am slightly modifing the recipe though, the original is as follows:
6.5 lbs Rahr 2-row pale
2 lbs German Munich
1 lb crystal 60

1.5oz cascade pellets at 60 (I think they are 5.5 alpha)
1 oz cascade pellets at 1

What I am doing:
7 lbs American 2-row, he didn't have Rahr and we figured why not make it an even 10 lbs total
2 lbs German Munich
1 lb crystal 60

1 oz cascade whole leaf 9.0 alpha at 60
1 oz cascade whole leaf at 5

I chatted with the shop owner about water volume for mashing and he was saying about 1-1/8 to 1-1/4 quarts of water per lb and bring the water up to 167 degrees or so to get a mashing temp in the mid 150's.

In all it was a good trip to the homebrew store, he had some corny's in stock so I grabbed another as well.


NateG is offline
 
Reply With Quote
Old 08-31-2012, 11:18 PM   #2
inhousebrew
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2012
Location: minneapolis, minnesota
Posts: 1,454
Liked 126 Times on 113 Posts
Likes Given: 36

Default

Good luck with everything. You all researched on method and ready to go?


__________________
I hate Walder Frey...
inhousebrew is offline
 
Reply With Quote
Old 08-31-2012, 11:24 PM   #3
Yooper
Ale's What Cures You!
HBT_ADMIN.png
Feedback Score: 0 reviews
 
Yooper's Avatar
Recipes 
 
Join Date: Jun 2006
Location: UP of Michigan
Posts: 65,440
Liked 6053 Times on 4313 Posts
Likes Given: 1557

Default

Looks good!

I'd suggest mashing in at 1.25-1.33 quarts of water per pound (so, 12.5-13.3 quarts), about 11 degrees warmer than your desired mash temp. I'd mash that at 152, so I'd mash in at 163 or so. Preheat your mashtun, and then keep a little boiling water handy and a few ice cube trays, just in case you miss high (or low).

But, before adjusting, stir well. Then stir some more, and cover it and let it sit a couple of minutes before doing anything. Sometimes, the thermometer reads high and people add a little boiling water and then it's too high and add some ice and go on and on.

Stir well, and let it sit for a minute to equalize. Then check the temp. If it's high or low, add a little ice or boiling water. Then stir well and check again after a few minutes. As long as you're in the 150-155 area, I'd let it go. Too many brewers go back and forth too high, too low, etc. Aim for 152-153, but accept a couple of degrees either way- and I promise it will be good!
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

Follow me on facebook: https://www.facebook.com/lorena.t.evans
But I'm pretty boring so don't expect much!
https://www.facebook.com/lorena.t.evans
Yooper is offline
SwivelHips Likes This 
Reply With Quote
Old 09-01-2012, 01:01 PM   #4
inhousebrew
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2012
Location: minneapolis, minnesota
Posts: 1,454
Liked 126 Times on 113 Posts
Likes Given: 36

Default

Quote:
Originally Posted by Yooper View Post
Preheat your mashtun, and then keep a little boiling water handy and a few ice cube trays, just in case you miss high (or low).
When I first started I was missing my mash temp pretty regularly but once I started adding a gallon of really hot water to my cooler mashtun to preheat it I started getting closer.
__________________
I hate Walder Frey...
inhousebrew is offline
 
Reply With Quote
Old 09-01-2012, 01:12 PM   #5
AndrewD
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2012
Location: Santa Rosa, CA
Posts: 289
Liked 49 Times on 33 Posts
Likes Given: 14

Default

kehaar here on HBT gave me some excellent advice for heating the cooler mashtun:

Quote:
Originally Posted by kehaar View Post
To preheat raise the mash water to 10-15 F above strike temp. Add that hot water to your tun and then close the lid for 15 minutes. After 15 min is up open the tun, measure the temp and then stir until the temp drops to your strike temp + 3F (room for error). Then add your grain and stir until the mash temp drops to your target mash temp (maybe 5 minutes of stirring).
While this method may take a few more minutes, it does allow you to add your malt to the mash at the precise temperature.
AndrewD is offline
 
Reply With Quote
Old 09-01-2012, 01:26 PM   #6
NateG
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2011
Location: Keizer, Oregon
Posts: 123
Liked 6 Times on 5 Posts

Default

Cool, all good advice, how much sparge water should I expect to prepare? For sparging I am probably going to put the water in my bottling bucket and use the large eye bolt I have in the load baring beam I use for pulling engines out of cars to hoist the bucket above the mash tun which will be on a tall stool above the boil kettle
NateG is offline
 
Reply With Quote
Old 09-01-2012, 01:43 PM   #7
alestateyall
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2011
Posts: 736
Liked 89 Times on 58 Posts
Likes Given: 5

Default

Quote:
Originally Posted by AndrewD
kehaar here on HBT gave me some excellent advice for heating the cooler mashtun:

While this method may take a few more minutes, it does allow you to add your malt to the mash at the precise temperature.
Thanks, AndrewD!
alestateyall is offline
 
Reply With Quote
Old 09-01-2012, 02:29 PM   #8
Yooper
Ale's What Cures You!
HBT_ADMIN.png
Feedback Score: 0 reviews
 
Yooper's Avatar
Recipes 
 
Join Date: Jun 2006
Location: UP of Michigan
Posts: 65,440
Liked 6053 Times on 4313 Posts
Likes Given: 1557

Default

Quote:
Originally Posted by NateG View Post
Cool, all good advice, how much sparge water should I expect to prepare? For sparging I am probably going to put the water in my bottling bucket and use the large eye bolt I have in the load baring beam I use for pulling engines out of cars to hoist the bucket above the mash tun which will be on a tall stool above the boil kettle
Well, let's see. You have 9 pounds of grain. So, you'd use 1.25-1.5 quarts per pound of grain in the mash. So, call it 12 quarts. That's 3 gallons for the mash. (Have a little boiling water handy nearby and some ice cubes, just in case you miss high or low- but stir VERY well and wait 5 minutes before adjusting anything!).

The grain should absorb about a gallon of water in the mash, so you'd get two gallons out of the mash as first runnings.

What is your boil volume going to be? If it's 6.5 gallons, and you get 2 gallons out of the mash, you'll need 4.5 gallons of sparge water.
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

Follow me on facebook: https://www.facebook.com/lorena.t.evans
But I'm pretty boring so don't expect much!
https://www.facebook.com/lorena.t.evans
Yooper is offline
 
Reply With Quote
Old 09-01-2012, 02:40 PM   #9
SwivelHips
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: Calgary, Alberta, Canada
Posts: 136
Liked 16 Times on 16 Posts
Likes Given: 13

Default

I've brewed a similar amber a couple of times, turns out great with Wyeast 1007. Good luck!
SwivelHips is offline
 
Reply With Quote
Old 09-27-2012, 03:49 AM   #10
NateG
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2011
Location: Keizer, Oregon
Posts: 123
Liked 6 Times on 5 Posts

Default

Well, three weeks in primary and a week in the keg and it's beer, still a little cloudy.


NateG is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
First AG tomorrow 54BelAir All Grain & Partial Mash Brewing 5 07-29-2011 08:07 PM
Mac & Jack African Amber - Mao's Red Hat Amber beerspitnight All Grain & Partial Mash Brewing 11 05-05-2011 01:42 AM
2nd Batch tomorrow MotleyBrue All Grain & Partial Mash Brewing 1 04-02-2011 12:00 AM
Trying something new tomorrow Decojuicer All Grain & Partial Mash Brewing 3 01-06-2009 12:04 AM
1st AG tomorrow mot All Grain & Partial Mash Brewing 15 03-17-2008 06:06 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS