Best way to use Temp Control probe - Home Brew Forums
Home Brew Forums > Home Brewing Beer > General Beer Discussion > Best way to use Temp Control probe
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 08-17-2012, 03:07 AM   #1
LarryC
Recipes 
 
Jun 2009
San Diego, CA
Posts: 728
Liked 12 Times on 11 Posts



I just finished wiring up my shiney new Ranco single stage temp controller. I am going to be using it to run a FermWrap around my Better Bottle placed inside of a temp controlled freezer. I've modified the freezer's factory temp control switch to the point where it will hold 40 pretty well but that means it's going to be mighty chilly in there. I was thinking I would tape the Ranco probe to the side of the Better Bottle where the FermWrap has a open space.

That seemed like a good idea until I did a simple test with a glass of water. This is sort of backwards but I was in the garage which was 84 and I filled a glass with water and taped the probe to the glass. I then tossed in a few cubes and waited for the temperature to drop and my Ranco to kick on. The surprising part was that the water in the glass was in the high forties but the temp probe never showed it getting below 67 (waited maybe 10 minutes). One thing to clarify, the glass wasn't real glass - it is one of those acrylic things about 1/8" thick.

So my question is, will taping the probe to the better bottle control the temperature as close as I'd like to be or do I have to get the probe into the fermenting wert?

And the experts say?



 
Reply With Quote
Old 08-17-2012, 06:08 PM   #2
eobie
Recipes 
 
Jan 2012
Mount Holly, NJ
Posts: 200
Liked 14 Times on 6 Posts


In the wort is always the best.



 
Reply With Quote
Old 08-17-2012, 07:52 PM   #3
kuphish
Senior Member
HBT_LIFETIMESUPPORTER.png
 
kuphish's Avatar
Recipes 
 
Dec 2008
Pittsburgh, PA
Posts: 197
Liked 4 Times on 3 Posts


Did you insulate the probe, or was it just taped against the glass container?

Also, I'm confused. Is your plan to have the freezer running at 40F while the FermWrap keeps the beer at fermentation temperature?

 
Reply With Quote
Old 08-17-2012, 08:00 PM   #4
aubiecat
Recipes 
 
Dec 2011
Alexander City, Alabama
Posts: 1,197
Liked 130 Times on 99 Posts


Quote:
Originally Posted by eobie View Post
In the wort is always the best.
^^This^^

 
Reply With Quote
Old 08-18-2012, 02:18 AM   #5
LarryC
Recipes 
 
Jun 2009
San Diego, CA
Posts: 728
Liked 12 Times on 11 Posts


Quote:
Originally Posted by kuphish View Post
Did you insulate the probe, or was it just taped against the glass container?

Also, I'm confused. Is your plan to have the freezer running at 40F while the FermWrap keeps the beer at fermentation temperature?
Yes, that's the plan. I'm converting my old chest freezer to a Keezer slowly but surely. The freezer will sit at about 40 F now with it's factory thermostat and the Ranco will be used to keep a FermWrap on the Better Bottle running so the fermentation temp stays around 65ish (depending on the recipe).

At some point I will probably set up a controller for the freezer temp to bring it up a little but for now, this is what I have.

 
Reply With Quote
Old 08-18-2012, 02:19 AM   #6
LarryC
Recipes 
 
Jun 2009
San Diego, CA
Posts: 728
Liked 12 Times on 11 Posts


Quote:
Originally Posted by eobie View Post
In the wort is always the best.
I wasn't sure if the probe was "wert" proof. It will be OK to just sanitize and drop it into the wert?

 
Reply With Quote
Old 08-29-2012, 09:29 PM   #7
cwi
Registered User
Recipes 
 
Jun 2010
Austin
Posts: 845
Liked 34 Times on 28 Posts


As suggested earlier, you need to insulate over the top of the taped probe for the 'probe on wall' strategy to work. It is the best possible location when using a controller to directly control a freezer/fridge when used as a ferm chamber. It works even better than a thermowell in the middle of the ferm vessel.

Your application is a little different, so I would guess you would need to add a bunch (3-4") of insulation for it to work even reasonably well. For your current approach, a thermowell placed near the vessel wall would be a better location, . This is what is meant by "in the wort". You cannot just place the probe in your wort, for sanitary reasons; or in a jug of water, for sensor non-waterproofyness reasons.

Even better, though, would be to just plug your keezer into the controller you do have, and tape its probe to the vessel wall, then insulate. Now your controller is controlling the temp of the ferm. Simpler, less energy, better temp control: win-win, win.

Of course, your keezer would not be suitable for much else while ferming, but that is the nature of trying to control ferm temps accurately. There are some guys who try to control multiple ferms using a single cold chamber and multiple heat wraps, but you really need to know what you are doing.

Getting a cheap/free fridge/freezer and a $25 ebay aquarium controller is a much simpler method, provided you have the room. Get another one of these controllers for your keezer, and you won't have to dismantle your thermostat every time you want to adjust your temps. A search on HBT will produce a link to a lengthy thread on them, but most of the information you need is in the first post. They have proven very reliable, with not a single confirmed failure reported to date. Just make sure you get a 110V version of the true STC-1000 controller.

A word of warning: your Ranco controller almost certainly does not have ASD to protect your compressor. You need to be very aware of this shortcoming, or it could cost you your compressor if used for a fridge/freezer. The information is available with a simple search.

 
Reply With Quote
Old 08-29-2012, 09:49 PM   #8
BetterSense
Recipes 
 
Jul 2011
Richardson, Texas
Posts: 1,024
Liked 55 Times on 45 Posts


I want to do exactly this thing, but not because I can't increase my keezer temps. I want to do it so that I can ferment ales in my keezer, and still leave my kegs at serving temperature, all in the same keezer. I think if I use a fermwrap around my carboy, it might work, but I don't know if a thermowell will be necessary.

 
Reply With Quote
Old 08-29-2012, 10:03 PM   #9
terrapinj
Recipes 
 
Dec 2010
Santa Monica, CA
Posts: 2,412
Liked 170 Times on 126 Posts


won't the fermwrap give off heat and impact the ambient temp inside the freezer?

 
Reply With Quote
Old 08-29-2012, 11:21 PM   #10
kuphish
Senior Member
HBT_LIFETIMESUPPORTER.png
 
kuphish's Avatar
Recipes 
 
Dec 2008
Pittsburgh, PA
Posts: 197
Liked 4 Times on 3 Posts


Quote:
Originally Posted by cwi View Post
Even better, though, would be to just plug your keezer into the controller you do have, and tape its probe to the vessel wall, then insulate. Now your controller is controlling the temp of the ferm. Simpler, less energy, better temp control: win-win, win.
I totally forgot about this thread. Glad I looked back. Your quoted text is exactly what I would suggest and the reason I posed the question earlier.

To the OP: I'm not sure I understand why you want to have the freezer and fermwrap working against each other. I agree with the quote above. It's much more efficient to just control the temperature of fermentation with the freezer by attaching an insulated probe to your fermentation vessel.

Good luck!




 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Temp Control Szimdars General Beer Discussion 10 11-07-2011 08:59 PM
Attaching Temp Probe to Bucket jww9618 General Beer Discussion 4 04-07-2011 11:55 PM
temp control? MichaelSterling General Beer Discussion 3 12-30-2010 10:06 PM
Temp control eagle83 General Beer Discussion 4 06-08-2010 03:47 PM
Temp control. No electricity jmo88 General Beer Discussion 7 12-12-2008 09:43 PM


Forum Jump