steeping specialty grains - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Beginners Beer Brewing Forum > steeping specialty grains

Reply
 
Thread Tools
Old 06-27-2012, 06:35 PM   #1
dfaridoni
Recipes 
 
Apr 2012
Hanford, Ca
Posts: 75


I was wondering if it makes any difference if you put you grain in and then bring the temp up to about 155 or bring it up to 155 and then put them in the boil pot. I've been doing it the first way and want to see if I'm doing it wrong.

 
Reply With Quote
Old 06-27-2012, 06:56 PM   #2
MarkB
HBT_SUPPORTER.png
Recipes 
 
Oct 2011
Goshen, Indiana
Posts: 39
Liked 1 Times on 1 Posts


I don't know if it makes much of a difference at all. I do it both ways, depending on what time I get the whole brewday started. It also depends on how much prep work I have done before getting the pot on the stove too. It is an interesting question, and I'd like to hear a definitive answer, but I doubt it will convince me to only ever do it one way, over the other....

Also, as I recall, the instructions from 2 separate kits I have bought each said one way. A Brewers Best kit said to bring water to temp then steep, while a Northern Brewer kit said to steep while bringing water to temperature. Granted, I could be wrong in remembering, but it sure rings a bell.

 
Reply With Quote
Old 06-27-2012, 07:16 PM   #3
CBXBob
HBT_SUPPORTER.png
 
CBXBob's Avatar
Recipes 
 
Mar 2012
Grants Pass/ Nuevo, Or. / Ca.
Posts: 486
Liked 100 Times on 65 Posts


Looking back at my instruction sheets, you can do it both ways. putting the grain bag in cold water, heat and remove bag a 170 degrees. Or heat water to 155 degrees, remove from heat add grain bag and steep for 25 minutes. I've done both, both were fine.

 
Reply With Quote
Old 06-27-2012, 07:47 PM   #4
dfaridoni
Recipes 
 
Apr 2012
Hanford, Ca
Posts: 75

Ok, thanks. I usually don't get the grain in until about 110 since I too get the burner going and then do some other stuff before I get to it. i think you're right on either way being ok and I'll go with that unless someone else comes up with a reason not too

 
Reply With Quote
Old 06-27-2012, 08:34 PM   #5
tnsen
Recipes 
 
Dec 2011
Muskegon, MI
Posts: 197
Liked 6 Times on 6 Posts


I have done all my extract kits the 1st way as in put the grains in and then heat water, regardless of the instructions,reason is a friend was over for my first batch who has been brewing many years, aka his method...as a side note, I will be doing my first biab soon , and I think ill do the same, mash in then start the heat, untill it hit my temp....bottom line I dont think I matters , just preferance.....Tom

 
Reply With Quote
Old 06-27-2012, 08:57 PM   #6
dfaridoni
Recipes 
 
Apr 2012
Hanford, Ca
Posts: 75

ok, I'll just keep on keeping then. Thanks

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
I didn't crush my specialty grains enough before steeping. Dude3000 Beginners Beer Brewing Forum 18 02-17-2012 03:27 AM
Steeping Specialty Grains BeerNut24 Beginners Beer Brewing Forum 3 12-19-2011 02:31 AM
Steeping specialty grains methods Daver77 Beginners Beer Brewing Forum 8 02-24-2011 02:09 AM
Steeping Specialty grains Meatball358 Beginners Beer Brewing Forum 12 08-12-2009 10:45 AM
Steeping specialty grains Mk010101 Beginners Beer Brewing Forum 6 12-29-2006 10:22 PM


Forum Jump