Replacing 2-prong cord with grounded cord - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Replacing 2-prong cord with grounded cord

Thread Tools
Old 07-04-2007, 02:06 AM   #1
Jan 2007
Santa Barbara, CA
Posts: 85
Liked 1 Times on 1 Posts

Hi Everyone, I tried getting some help from a home improvement forum but no responses so I'll call upon the brains from HBT!

Hopefully someone can help point me in the right direction. I recently acquired a c.1940ís Frigidaire refrigerator. It has a two prong unpolarized plug which has exposed wires in the plug so I would like to replace it with a grounded plug.

The problem I am having is I havenít ever done anything like this before so I have a bunch of questions.

First, Iím not sure how to tell which wire should be hot and which should be neutral. I found this website:
(go to table of contents, chapter 5, replacing the cord)

Which said that the one which is common with the outside of the light bulb holder is neutral. However, it also said that the part of the cord with ribbing is neutral. In my case the unribbed one is common with the outside of the light bulb holder. Does the fact the fridge is so old explain why that advice doesnít work? How should I determine what the neutral wire should be?

For the grounding, what is the best way to ground the fridge? My multimiter isnít showing any conduction between various parts of the frame, although that may just be from rust. Iím planning on just drilling a hole into the frame for grounding, does that sound good?

I am planning on cutting the current wire and splicing together with a replacement beyond where it is attached to the fridge. I canít access the junction box under the fridge easily. Is this a safe way to connect a new wire or should I try to get to the heart of the electronics?

Any other advice or hints or things I should know before embarking on this project? It doesnít seem to hard to me, but should this be something I should have someone else do for me?

Thank you very much for any help at all!
Double Mutt Brewing!

On deck: More Apfelwein
Primary 1: 011 Trippel
Primary 2: 010 Wit
Primary 3: empty
Kegged: 009 Zaca Fire Ash Hefeweizen
008 Summer Hefeweizen

Reply With Quote
Old 07-04-2007, 03:40 AM   #2
WOP31's Avatar
Feb 2007
Posts: 1,342
Liked 14 Times on 7 Posts

I had to replace the cord on my 1952 Philco Kegerator, I just used a two wire set up with a two pronged plug. If you are bound and determined to ground it out you should take the extra steps to replace the whole cord. i just spliced in and used heat-shrink, to seal it up. Also I think (my opinion) that you should go with the portion of the cord that is external, meaning not the part running ot the light bulb, of the fridge, in which case the ribbed part would be nuetral. again these are my opinions and in no way should be taken as fact, or coherent recomendations

"Yes, I am a pirate two hundred years too late. The cannons don't thunder there's nothin' to plunder,
I'm an [under] forty victim of fate, Arriving too late, arriving too late."
-Jimmy Buffet

Reply With Quote
Old 07-04-2007, 02:41 PM   #3
gnets99's Avatar
Jun 2007
Posts: 61

As far as which wire is common, I couldn't say for certain without actually seeing it. I would recommend calling an appliance repair shop and seeing if they can dig up some specs on the unit (see if you can find a mom and pop type place, they're usually more helpful). As far as adding a ground, most of the stuff in your home is grounded to the chassis or case that it's built in, so drilling a hole and adding a ground should work. Just make sure that that the screw or lug you use is making contact with bare metal.
Again, though, I can't really guarantee that this is accurate without actually seeing the unit. My recommendation is that if you're worried about causing any damge to the unit, yourself, or worse, I would either check with a repair shop or licensed electrician in your area.
"I like beer. I'll even drink a beer to celebrate a special occasion, such as the fall of communism or the fact that the refrigerator is still running" ~ Dave Barry
Primary: Holiday Ale
Secondary: Rapsberry Wheat
Kegged: Dark Lord of the Stout, Blonde Bombshell
Bottles: Bad Shark Ale, Summer Ale

Reply With Quote
Old 07-04-2007, 03:31 PM   #4
HenryHill's Avatar
Mar 2007
Perry, MI
Posts: 3,040
Liked 11 Times on 11 Posts

First, both wires in old plug run to hot. The third wire in a 3 wire is a ground to chassis, in case stray voltage happens to contact the chassis, it is run to ground for safety. Most things on 3 wire plugs are chassis grounded. Washer, for instance...older stuff not double grounded may require the third wire to operate.

Things that are 'double grounded' require no auxiliary ground to operate. It is inherent in their engineering, power tools for instance.

Never remove a ground from a 3 wire plug- but you can ADD chassis grounding to a 2 wire setup, by connecting the new GREEN ground connector ring to a screw that is screwed into the chassis.
Originally Posted by orfy
Never mock another man's brewery.
Originally Posted by IrregularPulse View Post
This is HBT of course. Normal Thread that goes every direction but the one intended. This forum should be scientific proof the beer causes ADD

Reply With Quote
Thread Tools

Similar Threads
Thread Thread Starter Forum Replies Last Post
NEW 30A 240v GFCI Plug-in ready to use cord! cyberbackpacker For Sale 19 11-25-2009 03:21 PM
help me put a temp swich on an extension cord ben_j8mmin Brew Stands 4 04-24-2009 07:42 PM
8/4 SOOW appliance cord juvinious Brew Stands 2 04-07-2009 12:33 PM
Heatstick questions: Why appliance cord? Why 3+Gr wires? learningmore Equipment/Sanitation 20 08-18-2008 09:48 AM
Temp controller-Length of Cord broadbill Equipment/Sanitation 2 01-21-2008 03:43 PM

Forum Jump