Getto Beer Gun?? - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > DIY Projects > Getto Beer Gun??

Reply
 
Thread Tools
Old 05-30-2012, 03:52 PM   #1
HopSong
Senior Member
HBT_LIFETIMESUPPORTER.png
 
HopSong's Avatar
Recipes 
 
Sep 2011
Santa Rosa, CA
Posts: 1,950
Liked 101 Times on 89 Posts



Suggestions please. I've seen folks use their party tap with a piece of acrylic plastic tube.. like the kind used for bottling.. to fill a growler or bottles. I don't have a tube that fits tightly inside the party tap so I used a piece of vinyl tubing as a connector between the tap and the plastic filler tube.

Well, following what I thought was right, I filled the first part into a glass to get rid of the foam.. but, after that it all foamed. It was like a venturi .. in a carburetor where the gas expands. It was nothing but brew with minute bubbles flowing into the bottles.. ending up with about 3/4 of a bottle and the rest foam..

For those of you who have tried this.. how do you do it?

What pressure do you set the regulator at? My kegs are at about 45*. Do you burp and set at a lower temp or ?? Oh, my beer is at about 14 PSI in the keg. I have a Carbonator which says I should use 20-30 PSI for optimum results.

Don't want just foam.... Thanks for any help.. cuz I don't really want to make Blickman any richer if I can get away with it....
__________________
Cheers, Bill
Hop Song Brewing

 
Reply With Quote
Old 05-30-2012, 03:59 PM   #2
DirtyOldDuck
 
DirtyOldDuck's Avatar
Recipes 
 
Jan 2012
Portland, Oregon
Posts: 552
Liked 70 Times on 61 Posts


Everything you need to know: http://www.homebrewtalk.com/f35/we-n...eer-gun-24678/. Racking canes are cheap or drill a stopper to fit your tubing.

 
Reply With Quote
Old 05-30-2012, 04:06 PM   #3
Jukas
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Dec 2011
Santa Rosa, CA
Posts: 976
Liked 103 Times on 79 Posts


I use BM's beergun alternative workaround above. Works great for me provided I do two things.

1) Set the regulator to no more than 2psi, you want just enough pressure to push beer through the lines, we're assuming it's already carb'd beer.
2) vent the keg prior to filling.

I do it at filling temps, and have a spare threaded ball lock liquid post that I attach to a 5' hose going to the picnic tap. When I want to fill bottles I just unhook the current beer lines, attach that one, set the psi down and vent the keg and go. I leave the keg in the fridge and just gently shut the door on the line.

 
Reply With Quote
Old 05-30-2012, 06:40 PM   #4
brewski08
Recipes 
 
Jan 2012
the library, michigan
Posts: 366
Liked 21 Times on 17 Posts


i use the picnic tap and bottling wand method discussed above. when i first started doing it, i was only able to get 3/4 of a beer bottle full. now i can get nearly 100% of it full...although i aim for around 90%.

here are some tips that i find helpful:

-make sure your bottles you intend to fill are very cold. as i'm sure you already know, CO2 will escape your beer if you poor it into a room temperature bottle.

-i burp my keg from its serving PSI down to 0 PSI...and then back up to ~2 PSI to fill the bottles. i find that any PSI between 1 and 5 is effective when filling bottles this way.

-in the link above, BierMuncher explains how the bottles should be tilted and swirled at the end of filling a bottle before capping in order to purge it of oxygen. although this method works, i don't find it necessary. i'll fill a bottle up all the way to the top, remove my bottling wand, and then top it off with some foam. then i will cap onto the foam. i find this way to be nearly 100% effective in removing oxygen from your beer bottle, and i've never had a problem with oxidation.

-make sure your rubber stopper makes a tight seal with your beer bottle. the idea behind this method is that the pressure that builds up inside your beer bottle pushes the foam down and prevents CO2 from escaping your beer. when you begin filling up your beer bottle with your rubber stopper secure, do not begin wiggling it until beer STOPS coming out of your tap. this indicates the pressure of your keg and bottle have met an equilibrium, and at this point, you should begin to slowly let air out of the bottle. the slower the fill, the less foam you will have.

here's a video that i found very helpful:


again, this method takes a little practice, and after filling a six pack of bottles, i'm sure you'll get the hang of it.

i use this method all the time with GREAT results. this is a great way to bottle beers as it does not leave that nasty, yeasty sediment behind.

 
Reply With Quote
Old 05-30-2012, 07:04 PM   #5
Jukas
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Dec 2011
Santa Rosa, CA
Posts: 976
Liked 103 Times on 79 Posts


FYI BM stated later in the thread he no longer worries about freezing/super chilling the bottles, but does mention filling them wet really helps.

I do the same, sani the bottles then have a pitcher full of sanitizer, I dunk the bottles to give them a last minute wash in sanitizer, then fill and have zero problems with foam.

 
Reply With Quote
Old 05-30-2012, 07:34 PM   #6
bcgpete
Recipes 
 
Jun 2010
Poulsbo, WA
Posts: 211
Liked 6 Times on 6 Posts


I've just been filling straight from my taps. I turn my regulator to about 2psi, purge the keg, the go. It takes about 3 minutes/bottle, and a few foam a little. I just cap on the foam and haven't had any trouble with carbonation after everything settles, even a few weeks later.

 
Reply With Quote
Old 05-30-2012, 09:59 PM   #7
DeafSmith
HBT_LIFETIMESUPPORTER.png
 
DeafSmith's Avatar
Recipes 
 
Jan 2009
Richardson, TX
Posts: 1,448
Liked 34 Times on 32 Posts


Quote:
Originally Posted by Jukas View Post
FYI BM stated later in the thread he no longer worries about freezing/super chilling the bottles, but does mention filling them wet really helps.

I do the same, sani the bottles then have a pitcher full of sanitizer, I dunk the bottles to give them a last minute wash in sanitizer, then fill and have zero problems with foam.
Has anyone tried using cold sanitizer with room temperature bottles? Looks like you could sanitize the bottle, chill it, and wet it all in one operation.

 
Reply With Quote
Old 05-30-2012, 10:46 PM   #8
starsailor
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Jan 2008
Central MA
Posts: 281
Liked 12 Times on 12 Posts


Quote:
Originally Posted by DeafSmith View Post
Has anyone tried using cold sanitizer with room temperature bottles? Looks like you could sanitize the bottle, chill it, and wet it all in one operation.
That sounds like a great idea to kill 2 birds with one stone, and you only need to find space in the fridge for one jug of sanitizer too.
__________________
On Tap: Apfelwein, SkeeterPee
Bottled: Robust Porter, Roasty Toasty Stout, Belgian Wit, Belgian Saison
Kegged: None
Primary: Rye-I-Brew Belgian Rye Saison
Secondary: None
On Deck: Wheat ale
RIP: BadBoy Wit, Wild Cider, Got Mild?x2, Wyeast Cider-2x, SO4 Cider, Wheat ale, Carnival Kölsch-2x, Am Pale Ale, Am Brown Ale, Dunkel Larger, Erik The Red, Newporter, Cream Ale, Bitter, Trapist Triple, Bourbon Oaked Porter, Gluteus Minimus(Gluten Free)-2x, English Brown

Wizards Homebrew Club

 
Reply With Quote
Old 05-31-2012, 10:02 PM   #9
krazydave
 
krazydave's Avatar
Recipes 
 
Aug 2010
Santa Clarita, California
Posts: 924
Liked 32 Times on 30 Posts


I use BM's stopper on a plastic tube concept, but I go straight from my perlick tap rather than a picnic tap. To get a good seal in the tap, I use a Bowie bottling adapter (search the forums). Though the tubing that you usually use for racking fits into the Perlicks just fine much like it does the cobra taps, I decided to spend the money on something a little cleaner.
Using that method, I usually don't get any foam as long as I'm slow about the process and burp the air slow. I'm also usually too lazy to drop the pressure on my kegs and for the most part don't have a problem with it, other than the occasional filling of a bottle too much and getting a high pressure shot of beer in my eye when I go to burp the last bit (everyone needs a beer shower on occasion!).

 
Reply With Quote
Old 05-31-2012, 10:09 PM   #10
day_trippr
Recipes 
 
May 2011
Stow, MA
Posts: 17,168
Liked 2925 Times on 2184 Posts


Quote:
Originally Posted by bcgpete View Post
I've just been filling straight from my taps. I turn my regulator to about 2psi, purge the keg, the go. It takes about 3 minutes/bottle, and a few foam a little. I just cap on the foam and haven't had any trouble with carbonation after everything settles, even a few weeks later.
3 minutes per bottle?

Is that a typo - or do you have an extraordinary amount of patience and dedication?

Cheers!

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Getto Mr Beer Cooler Build virus692 Fermenters 3 03-10-2009 07:31 PM


Forum Jump