Cleaning Freezer lid gaskets - Home Brew Forums
Home Brew Forums > Home Brewing Beer > DIY Projects > Fermenters > Cleaning Freezer lid gaskets

Reply
 
Thread Tools
Old 05-14-2012, 02:09 PM   #1
KingKlong
Recipes 
 
May 2012
Kernersville, NC
Posts: 147
Liked 3 Times on 2 Posts



So I just got a used freezer, and the thing was pretty filthy. Over the weekend I cleaned it thouroughly, and I'm pretty happy with how it turned out except for the lid gasket. I'm slightly worried about it.

It had quite a bit of black mold on it. After removing the gasket from the lid, and soaking it in a bleach solution most of the gasket looks as good as new. There are a few spots though that just don't want to come off!!

Since it's been in bleach is there no reason to be concerned now, or does the gasket need to be 100% bright white?



 
Reply With Quote
Old 05-14-2012, 03:34 PM   #2
GoodDogShelby
Recipes 
 
Mar 2012
Erlanger, KY
Posts: 219
Liked 30 Times on 24 Posts


If you think you still have some mold, go to Home Depot. In their tool rental department they have a product called "Mold Control". It works great in killing mold and keeping it from coming back.

That said, you probably won't get that gasket bright and shiny white.

I bought a freezer from CL over the weekend and it looked very clean. When I got it home I realized that it had the horrible smell of cheap cigarets. It really reeks. I scrubbed it with Oxyclean inside and out, top to bottom. I figure I've got a couple of more scrubbing to do before it leaves the garage.



KingKlong Likes This 
Reply With Quote
Old 05-14-2012, 03:41 PM   #3
shelly_belly
Chilly Winds
HBT_SUPPORTER.png
 
shelly_belly's Avatar
Recipes 
 
Jul 2009
Rabbittown, Bama
Posts: 1,646
Liked 182 Times on 145 Posts


I had to use bleach and a toothbrush to get rid of some stubborn mold on mine. Also, to get rid of some foul odor, I had to replace the insulation in the lid.

KingKlong Likes This 
Reply With Quote
Old 05-14-2012, 04:04 PM   #4
KingKlong
Recipes 
 
May 2012
Kernersville, NC
Posts: 147
Liked 3 Times on 2 Posts


My gasket is bright and shiny except for these few freckle like places where the black is being stubborn. Most of them are in the crease that squishes, but some are on the flat sealing surface. I started with Charlies soap, then used a Mr. Clean magic eraser and now have had it soaking in bleach. I'm going to look for the Mold Control product you mentioned GoodDogShelby. Thanks.

ShellyBelly, I've been thinking of using a toothbrush, but was trying to avoid it. I got my freezer on CL, and after a thourough cleaning these few places are the only thing remaining. Other than a dent and few scratches.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Who Sells Large Silicone Gaskets? Cpt_Kirks DIY Projects 15 01-18-2013 06:49 PM
fridge seals/gaskets Broncobum Fermenters 11 11-29-2011 01:05 AM
PTFE Chemical Flange Gaskets Cubslover Kettles, Mash Tuns & Hot Liquor Tanks 0 08-08-2011 12:34 AM
proflowdynamics gaskets scottgar12 Brew Stands 4 05-24-2011 02:59 AM


Forum Jump