Home Brew Forums > Home Brewing Beer > DIY Projects > Other > Question for Yuri & other Arduino users
Reply
 
Thread Tools
Old 05-13-2012, 06:21 PM   #1
chuckjaxfl
Feedback Score: 1 reviews
Recipes 
 
Join Date: Feb 2010
Location: Jacksonville, FL
Posts: 327
Liked 21 Times on 13 Posts
Likes Given: 23

Default Question for Yuri & other Arduino users

Question for those of you that are really experienced w/ Arduino.

I just bought an UNO about 4-5 weeks ago, and have been teaching myself the code and the circuitry. The last time I wrote code, it was in ďClipperĒ for dBase III+ (read: a long time ago).

Iíve got the thing reading a DS18B20 successfully, running PID, and writing to an LCD the way I want. Iíve got it running on breadboards now, controlling a crock pot. My code is crude and mostly plagiarized, but is working exactly like I want it to. Iím cooking a lamb sous vide right here on my desk.... pretty cool. Iím asking it for 135.00F and itís giving me 135.05F. So, itís time to come off of the breadboard an onto something permanent.

The original plan was to install the UNO in my control box, and make a shield (practicing w/ the PWM project I have in other threads). Then I found the Arduino ďnanoĒ on ebay for $12, and decided to use that. I was going to make a board, and install the nano on it like a chip. Then...

Finally, I just finally ďgot itĒ what they mean by prototyping platform. Donít laugh, but I just figured out that the intent is to get the project working, then rip the 328 off of the UNO, install it into a 28 pin socket on my own board, and then use the UNO over & over & over again with a fresh 328 each time.

I notice that Yuri went the shield route.

Further, I donít see too many projects where people have just removed the 328 and used that... so the question is: Why not? I have to make a board regardless of the decision. A new 328 w/ the UNO bootloader is <$5, and it would seem MUCH easier to integrate a DIP28 onto my own board rather than adapt the Arduino (UNO or Nano, either one) to it. What is it that Iím not realizing?


chuckjaxfl is offline
 
Reply With Quote
Old 05-13-2012, 07:21 PM   #2
cjang
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: Riverside, CA
Posts: 28
Liked 4 Times on 3 Posts

Default

I think its more for convenience. With an uno, you don't have to; do much soldering, work on a stripboad, build a power supply, and have a separate ftdi programmer. An atmega328 stand alone is much cheaper and more compact. That's the way I like to go.


cjang is offline
 
Reply With Quote
Old 05-13-2012, 07:29 PM   #3
luke_l
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2012
Posts: 16
Liked 2 Times on 1 Posts

Default

There's a page on the arduino site http://arduino.cc/en/Tutorial/ArduinoToBreadboard which explains how to use an arduino on a breadboard. I play around with little arduino projects all the time, I always build a circuit on a breadboard, get it working, and solder it up. I basically only use my arduino board as an in circuit programmer to put the bootloader on new 328's, and I use it to connect the breadboard to USB as per the above link.

Good luck!
luke_l is offline
 
Reply With Quote
Old 05-13-2012, 07:55 PM   #4
huntb
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2012
Location: Grand Haven, Michigan
Posts: 180
Liked 18 Times on 16 Posts
Likes Given: 22

Default

Make sure to add in proper circuit protection and an input capacitor for voltage stabilization, other than that there is nothing wrong with removing it from the Arduino and soldering it down to your own HW. Be sure to use proper ESD protection too!
huntb is offline
 
Reply With Quote
Old 05-13-2012, 09:25 PM   #5
chuckjaxfl
Feedback Score: 1 reviews
Recipes 
 
Join Date: Feb 2010
Location: Jacksonville, FL
Posts: 327
Liked 21 Times on 13 Posts
Likes Given: 23

Default

Quote:
Originally Posted by luke_l View Post
There's a page on the arduino site http://arduino.cc/en/Tutorial/ArduinoToBreadboard which explains how to use an arduino on a breadboard. I play around with little arduino projects all the time, I always build a circuit on a breadboard, get it working, and solder it up. I basically only use my arduino board as an in circuit programmer to put the bootloader on new 328's, and I use it to connect the breadboard to USB as per the above link.

Good luck!
Thanks for the link. I actually read that a few weeks ago, but comprehended none of it. Now looking it over again (with a few weeks under my belt), it all makes perfect sense and describes pretty much *exactly* what I'm talking about.


chuckjaxfl is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY Steam Mash System by Yuri Yuri_Rage Brew Stands 43 12-31-2011 12:55 PM
Question For Igloo Ice Cube Users... jpalarchio Kettles, Mash Tuns, & Hot Liquor Tanks 3 11-17-2009 02:28 AM
First Step in HERMS Conversion...Thanks Yuri and all others maxbing Brew Stands 3 08-09-2009 02:28 PM
Future Project for Yuri? mmb Other 1 06-25-2008 01:27 PM
Yuri: Congrats (Make Blog) scoates Brew Stands 1 05-01-2008 02:25 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS