Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > smaller cooler?
Reply
 
Thread Tools
Old 05-05-2012, 06:43 PM   #1
thomasben
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: eugene, Oregon
Posts: 178
Default smaller cooler?

I have a 70 qt extreme cooler. Same brand a lot of brewers use and was wondering if I'd benefit from holding temperature and getting higher efficiency with a smaller cooler. My set up is designed for more higher gravity beers. I get about 72% everytime but lose 5-6 degrees during my 90 MIN mash. Even with the cooler wrapped in blankets. The corners even drop more


thomasben is offline
 
Reply With Quote
Old 05-05-2012, 06:55 PM   #2
chumpsteak
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: Meridian, ID
Posts: 852
Liked 95 Times on 79 Posts
Likes Given: 13

Default

I have a 48 qt cooler and when I do 5 gallon batches I lose about 2 degrees in 60 minutes. With 10 gallon batches and the cooler as full as I can get it I lose 0 degrees in 60 minutes. So yes, I would say you would benefit from less open space. Get a smaller cooler or make bigger batches.


chumpsteak is offline
 
Reply With Quote
Old 05-05-2012, 07:33 PM   #3
thomasben
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: eugene, Oregon
Posts: 178
Default

So the dead space is whats doing it basically?
thomasben is offline
 
Reply With Quote
Old 05-05-2012, 10:58 PM   #4
webgodhog
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2010
Location: Fayetteville, Arkansas
Posts: 125
Liked 1 Times on 1 Posts

Default

The dead space will only affect the temperature if you open the lid during the mash. The temp will stabilize (lose maybe 1 degree to do this) and after that, it should stay the same. I've never had problems with a 60 qt cooler for my 5 gallon batches. I just set it and leave it and lose at most 1 degree
__________________
Quote:
Originally Posted by Reno_eNVy View Post
But fear not, I'm still your post-whoring champion.... god I hate myself....
Delperdang Brewery BrewShuffle
webgodhog is offline
 
Reply With Quote
Old 05-05-2012, 11:26 PM   #5
thomasben
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: eugene, Oregon
Posts: 178
Default

Something is wrong with my insulation then because I never open it
thomasben is offline
 
Reply With Quote
Old 05-06-2012, 01:20 PM   #6
webgodhog
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2010
Location: Fayetteville, Arkansas
Posts: 125
Liked 1 Times on 1 Posts

Default

Do you pre-heat your cooler? Being that much larger than your mash, I would think that could be a problem if you don't
__________________
Quote:
Originally Posted by Reno_eNVy View Post
But fear not, I'm still your post-whoring champion.... god I hate myself....
Delperdang Brewery BrewShuffle
webgodhog is offline
 
Reply With Quote
Old 05-06-2012, 01:33 PM   #7
ChemE
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2008
Location: Columbia, SC
Posts: 603
Liked 17 Times on 10 Posts
Likes Given: 4

Default

If you haven't already, try running aluminum foil over the edges of the cooler before you close the lid and wrap everything in blankets. Hot mash has a very low emissivity meaning it readily loses heat via radiation to the cooler lid. If the lid's surface is aluminum rather than plastic a massive portion (around 95%) of that energy is radiated back to the mash which readily takes it back up due to its low emissivity. It also has the added benefit of decreasing convective losses since these picnic coolers lack gaskets (that would be another way to boost your heat retention btw).
__________________

My Super Efficient 5-Gallon Mash Lauter Tun Graduating Carboys Leaf Hop Absorption Measured
Primary - Bemused Bitter, Munich Saaz SMaSH
Secondary - Air
Bottled - Oatmeal Stout 2011, Apfelwein, Withdrawn Wheat, Bourbon Barrel Barleywine SMaSH, Christmas Ale 2010, Perplexed Pale Ale
ChemE is offline
 
Reply With Quote
Old 05-06-2012, 10:19 PM   #8
thomasben
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: eugene, Oregon
Posts: 178
Default

I've always preheated but I'm wondering if I'm using hot enough water or even enough water for that matter?....how much water would you guys use to preheat a 70qt mash tun. Sometimes I use hot faucet water or like.130-150 degree. Maybe half full
thomasben is offline
 
Reply With Quote
Old 05-07-2012, 01:25 AM   #9
chumpsteak
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2011
Location: Meridian, ID
Posts: 852
Liked 95 Times on 79 Posts
Likes Given: 13

Default

I've found near boiling water works the best in my cooler. I throw in about a gallon, slosh it around and let it sit for a few minutes.
chumpsteak is offline
 
Reply With Quote
Old 05-07-2012, 04:21 AM   #10
ron,ar
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2007
Location: Little Rock, arkansas
Posts: 322
Liked 26 Times on 20 Posts
Likes Given: 5

Default

I use a 10 gallon round cooler for MLT and always preheat. I bring my HLT water up to 185-190. I preheat using the correct amount of mash water with the lid on the cooler. Let it sit for about 15 minutes, then open the lid, check temp, add grains at about 175 to 180 works for me, but a tall round mlt heats up easier because heat rises more uniformily.


ron,ar is offline
 
Reply With Quote
Reply


Thread Tools



Forum Jump

Newest Threads

LATEST SPONSOR DEALS