My single tier LPG/eRIMS build - Page 3 - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > My single tier LPG/eRIMS build

Reply
 
Thread Tools
Old 04-26-2012, 04:09 AM   #21
rossi46
Senior Member
HBT_SUPPORTER.png
 
rossi46's Avatar
Recipes 
 
Jan 2011
Pasco, WA
Posts: 863
Liked 76 Times on 58 Posts


Quote:
Originally Posted by fxdude
Looking great
Thanks. Just need more time to work on it.

 
Reply With Quote
Old 04-29-2012, 05:12 PM   #22
rossi46
Senior Member
HBT_SUPPORTER.png
 
rossi46's Avatar
Recipes 
 
Jan 2011
Pasco, WA
Posts: 863
Liked 76 Times on 58 Posts


Got the burners mounted. Adjustable height, 2,3,and 4 inches.
Can't find the right gas fittings I want here in town, I'll have to find some on the net somewhere. 3/8 female flare to 1/4 male pipe for the orifice to needle valve.
Click image for larger version

Name:	image-3405369775.jpg
Views:	551
Size:	69.2 KB
ID:	59337  

 
Reply With Quote
Old 04-30-2012, 12:51 AM   #23
rossi46
Senior Member
HBT_SUPPORTER.png
 
rossi46's Avatar
Recipes 
 
Jan 2011
Pasco, WA
Posts: 863
Liked 76 Times on 58 Posts


Got my very simple pump shields made today.
Click image for larger version

Name:	image-3153063050.jpg
Views:	525
Size:	65.4 KB
ID:	59421  

 
Reply With Quote
Old 04-30-2012, 12:57 AM   #24
Kylito87
Recipes 
 
Feb 2010
Chicago, Illinois
Posts: 66
Liked 2 Times on 2 Posts


Nice clean brew rig . Also the bike Can't go wrong with a springer front end!!!!

 
Reply With Quote
Old 04-30-2012, 01:41 AM   #25
StainlessBrewing
 
StainlessBrewing's Avatar
Recipes 
 
Sep 2009
Gilbert, AZ
Posts: 785
Liked 86 Times on 72 Posts


This setup is looking good! Was it a tough decision trying to figure out if you want to put the pumps above or below the tube? Once you get the connectors on they look like they're going to be pretty low.
__________________
Stainless Brewing LLC
Equipment, fittings, valves, tubing, accessories, kegging, custom fabrication and more.
Stainless is Painless at www.stainlessbrewing.com

 
Reply With Quote
Old 04-30-2012, 02:22 AM   #26
rossi46
Senior Member
HBT_SUPPORTER.png
 
rossi46's Avatar
Recipes 
 
Jan 2011
Pasco, WA
Posts: 863
Liked 76 Times on 58 Posts


I knew I wanted them under because the rims and chiller, also the shields would be super easy to make.
The inlet will be about 10"
Click image for larger version

Name:	image-240272977.jpg
Views:	513
Size:	40.9 KB
ID:	59441  

 
Reply With Quote
Old 04-30-2012, 02:50 AM   #27
StainlessBrewing
 
StainlessBrewing's Avatar
Recipes 
 
Sep 2009
Gilbert, AZ
Posts: 785
Liked 86 Times on 72 Posts


Plenty! It looks a lot lower in the other picture.
__________________
Stainless Brewing LLC
Equipment, fittings, valves, tubing, accessories, kegging, custom fabrication and more.
Stainless is Painless at www.stainlessbrewing.com

 
Reply With Quote
Old 04-30-2012, 10:17 AM   #28
Dougie63
Recipes 
 
Jul 2011
St Petersburg, FL
Posts: 277
Liked 7 Times on 6 Posts


on the shields you need to put a 30 deg angle on each side cradling the pump because when they are flat and liquid drips on them it can flow under and damage pumps

 
Reply With Quote
Old 04-30-2012, 01:47 PM   #29
rossi46
Senior Member
HBT_SUPPORTER.png
 
rossi46's Avatar
Recipes 
 
Jan 2011
Pasco, WA
Posts: 863
Liked 76 Times on 58 Posts


Ok, thanks Dougie

 
Reply With Quote
Old 05-04-2012, 03:57 AM   #30
rossi46
Senior Member
HBT_SUPPORTER.png
 
rossi46's Avatar
Recipes 
 
Jan 2011
Pasco, WA
Posts: 863
Liked 76 Times on 58 Posts


Got my control panel pieces put in, still need to wire. Waiting on some gas plumbing parts and a couple of ball valves.
Click image for larger version

Name:	image-1573618477.jpg
Views:	445
Size:	55.8 KB
ID:	60016   Click image for larger version

Name:	image-228459122.jpg
Views:	447
Size:	58.1 KB
ID:	60017   Click image for larger version

Name:	image-1174198893.jpg
Views:	427
Size:	25.5 KB
ID:	60018  

 
Reply With Quote
Reply
Thread Tools



Forum Jump