Is 20' of tubing enough for an Immersion Wort Chiller? - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > DIY Projects > Is 20' of tubing enough for an Immersion Wort Chiller?

Reply
 
Thread Tools
Old 02-17-2012, 11:20 PM   #1
cmduchaine
Recipes 
 
Feb 2012
Tumwater, WA
Posts: 1


I want to build an Immersion Wort Chiller out of copper tubing for as little cash as possible. The cheapest place to buy copper tubing (Home Depot) only sells it in coils of 20' or 50'. I'd prefer not to spring for the 50', and all the Chillers I have seen are made from 25' or more. I'm wondering if 20' will cut it. I brew 3 gallon batches and add them to another 2 gals of water in the fermenter.


 
Reply With Quote
Old 02-17-2012, 11:27 PM   #2
worksnorth
 
worksnorth's Avatar
Recipes 
 
Apr 2011
Soldotna, Alaska
Posts: 684
Liked 64 Times on 50 Posts


20' in 3 gallons of wort should be fine. I started with 20' in 5 gallon batches (wort) but graduated to 40' (added another 20') when I started making 10 gallon batches.

 
Reply With Quote
Old 02-18-2012, 12:11 AM   #3
paparker21
Recipes 
 
Jan 2012
Nasvhille, TN
Posts: 196
Liked 3 Times on 3 Posts


Save the money until you can afford 50' coil. keep an eye on ebay- i saved about 15$ even after shipping by ebaying the copper. make sure you look for cleaned and capped copper tubing.

the 20' will work, yes, but a 50' will work MUCH better and will allow you room to grow. technically, you can extend your 20' section through the use of compression fittings, but there will be SIGNIFICANT hassle in doing that. You'll be much happier if you wait until you can afford the 50' coil and don't have to swap out later.

you'll get a colder chill now as well and as a result will precipitate out more break material.

 
Reply With Quote
Old 02-18-2012, 05:18 AM   #4
day_trippr
Recipes 
 
May 2011
Stow, MA
Posts: 17,533
Liked 3014 Times on 2255 Posts


The op is boiling a mere three gallons. I suspect it would be pretty difficult coming up with an IC design using 50' of tubing that would even fit in such a small vessel.

20' will work for three gallons if the water supply is cold enough. If the op graduates to bigger batches he can spring for another 20' and grow his coil to fit the bigger vessel. Going straight to 50' would be massive overkill even if he could fit all that copper in his kettle...

Cheers!

 
Reply With Quote
Old 02-18-2012, 05:24 AM   #5
Rbeckett
 
Rbeckett's Avatar
Recipes 
 
Dec 2011
Bronson, Fl
Posts: 995
Liked 70 Times on 49 Posts


20 feet is enough, but 25 or 50 is better. The difference you will see with the various lengths is the amount of time it takes to go from boiling to pitching temp. The faster you can cool your wort to pitching temp the better. The cold break will be more pronounced and your beer will be less cloudy. You also expose your wort for less time to possible infections from stuff just floating around in the air like pollen. So a 20 footer will do, but 25 and 50 are much faster and if you ever decide to do a 10 or more gallon batch your time will suffer considerably. Have fun!!!
Bob
__________________
What do you mean "no Kidneys"???, WTF now I gotta drink less beer...
Join the Automation sub forum in Electric brewing for a discussion of components and control systems. I did!!!!

 
Reply With Quote
Old 02-18-2012, 05:26 AM   #6
paparker21
Recipes 
 
Jan 2012
Nasvhille, TN
Posts: 196
Liked 3 Times on 3 Posts


Quote:
Originally Posted by day_trippr View Post
The op is boiling a mere three gallons. I suspect it would be pretty difficult coming up with an IC design using 50' of tubing that would even fit in such a small vessel.

20' will work for three gallons if the water supply is cold enough. If the op graduates to bigger batches he can spring for another 20' and grow his coil to fit the bigger vessel. Going straight to 50' would be massive overkill even if he could fit all that copper in his kettle...

Cheers!
He probably uses a 20qt pot - it's what most LHBS will sell to starting brewers; it's what I use myself. I boil 3 gallons wort and actually end up having to top off with 3 gallons to the fermenter. My 50' coil fits fine.

 
Reply With Quote
Old 02-18-2012, 06:04 AM   #7
rjsnau
Recipes 
 
Feb 2011
Phoenix, AZ
Posts: 214
Liked 9 Times on 8 Posts


I vote wait for 50. I just upgraded from 25 to 50 for 5 gallon batches and notice a huge difference.

 
Reply With Quote
Old 02-18-2012, 07:03 AM   #8
setexmd
Recipes 
 
Dec 2011
San Augustine, TX
Posts: 2

I normally do five gallon batches and use a 20 foot IC. Works very well. But I do agree that if it fits into to pot 50 feet would be better. Especially if there is a chance that you will be doing 10 gal or more in the future. Always look towards the future and you only have to buy it once.

 
Reply With Quote
Old 02-18-2012, 07:27 AM   #9
skidaddytn
Recipes 
 
Nov 2009
knoxville, tn
Posts: 116
Liked 2 Times on 2 Posts


I have a 50ft stainless immersion chiller (which i love cause it doesnt get nasty like copper), but if i was still brewing 3g and topping off at the fermenter (which i used to), I would recommend a turkey fryer first... for some reason I think brewing the whole volume is more important than cooling it super fast... you may lose clarity, but the taste might be better... you can get a 7.5g turkey fryer on sale cheap at several stores... it will take over an hour to cool for sure without immersion chiller... so this will add waiting time :-(

 
Reply With Quote
Old 02-18-2012, 09:16 AM   #10
Dhruv6911
Recipes 
 
Nov 2008
Orange County, California
Posts: 187
Liked 3 Times on 3 Posts


Quote:
Originally Posted by rjsnau View Post
I vote wait for 50. I just upgraded from 25 to 50 for 5 gallon batches and notice a huge difference.
Do you have a time figure in difference or estimate? i'm looking to save water as 20 minutes of running water adds up to both a waste and a mess

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
3/16" Copper Tubing for Immersion Chiller? wittmania Chillers & Stir Plates 3 03-12-2011 04:32 PM
Immersion Chiller Tubing ?????????? thedude00 Chillers & Stir Plates 9 05-19-2010 11:20 PM
Another immersion chiller thread 5/8 tubing travs69 Chillers & Stir Plates 18 12-17-2009 05:00 PM
My new immersion wort chiller ramz7887 Chillers & Stir Plates 1 07-12-2009 08:57 PM
immersion chiller tubing FEARDIZ Chillers & Stir Plates 14 09-08-2008 07:11 PM


Forum Jump