Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > MLT Manifold Hole Size- Too Big?
Reply
 
Thread Tools
Old 01-30-2012, 02:59 PM   #1
Copperpots_Brewing
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2011
Location: Cleveland, OH
Posts: 239
Liked 2 Times on 2 Posts

Default MLT Manifold Hole Size- Too Big?

I have a friend who just built his cooler MLT and he made a CPVC manifold that has the holes drilled into it. He is getting pretty low efficiencies, like he is having a very hard time hitting 75%. Could it be because of how large the holes that are drilled in the manifold are? They are about maybe a little over 1/8" wide. They are big enough that he uses a strainer when draining the MLT because large pieces of grain husks come through near the beginning of the runnings. I dont really understand the science behind it to explain it to him, but I remember reading somewhere that the size of the holes could affect efficiencies. Can someone explain it to me?

Also, could it possibly be from his LHBS mill? He goes to Grape and Granary in Akron, OH (if anyone's been there). He uses a different store than I do, so i cant rule the crush out.

Any thoughts or input would be greatly appreciated!


Copperpots_Brewing is offline
 
Reply With Quote
Old 01-30-2012, 03:29 PM   #2
PoppinCaps
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2011
Location: Durham, NC
Posts: 430
Liked 14 Times on 13 Posts

Default

My vote is the crush. I've made several different manifolds for my system, and the only thing that ever really affected the efficiency was the mill gap setting. Recently my efficiencies had slowly dropped from 85% down to 75%, so I checked the gap and it had drifted up to .039". So I cranked it down to around .032" (I originally had it set at .035"), and it jumped right back to 85%, with no differences in the recipe or process, and no husks in the recirculation. Beyond that, making sure the lauter is long, like 45-60min will also get you a few points (assuming he's fly sparging). I'd keep the holes many and small, and focus on the crush instead.


PoppinCaps is offline
 
Reply With Quote
Old 01-30-2012, 07:27 PM   #3
Copperpots_Brewing
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2011
Location: Cleveland, OH
Posts: 239
Liked 2 Times on 2 Posts

Default

I'll have him try a different grain mill, see of that helps. I'll also let him know about draining slowly. That could very well be why I'm usually around 75 as well, I open my valve about half way. It drains in about 7 minutes.
So you basically open it to were it just trickles out?
Copperpots_Brewing is offline
 
Reply With Quote
Old 01-31-2012, 02:51 AM   #4
PoppinCaps
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2011
Location: Durham, NC
Posts: 430
Liked 14 Times on 13 Posts

Default

Yeah, for a batch sparge it doesn't matter, but fly sparging you want it to really just trickle out, keeping 1 inch or so of water consistently on top of the grain bed. I tried a 30 min lauter a few batches ago just to see, and the efficiency dropped 4 points or so.
PoppinCaps is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
manifold size????? lokiua4 All Grain & Partial Mash Brewing 2 04-25-2010 04:46 AM
Upgrade to all grain bk size vs. hlt. size timr62 All Grain & Partial Mash Brewing 6 02-09-2010 03:46 PM
Hole in mash tun need advice ddrayne10 All Grain & Partial Mash Brewing 4 11-03-2009 01:34 AM
Suggestions on false bottom hole pattern phreephly All Grain & Partial Mash Brewing 4 08-25-2009 06:23 PM
Optimal size & spacing for copper manifold for mash tun SamuraiSquirrel All Grain & Partial Mash Brewing 3 07-04-2009 10:22 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS