Polarware 42qt problems - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Polarware 42qt problems

Reply
 
Thread Tools
Old 01-12-2012, 05:52 PM   #1
etho1416
Recipes 
 
Nov 2011
Yonkers, NY
Posts: 11
Liked 1 Times on 1 Posts



I am really disappointed with this brewpot. I went with it instead of the megapot since it is made the USA, but I guess that does not mean that much any more.

Does anyone know if older version of this are welded on the inside? I swear I saw an odler one where the two holes are welded both on the outside and inside of the pot. Since mine is not welded on the inside, there is a really tight space where crud could hide and infiect my next beer.

Does anyone know how to get the ball valve all the way on? It won't screw all the way on, it feels like it is going to snap. It gets tight, but there is a few millimeters of exposed thread between the valve and the pot on the inside of the valve. This has me worried that crud will collect in there, be difficult to clean out, and ruin my next beer. Or I'll have to take the darn thing off and clean it every single time I use it.

I am serioulsy considering selling this thing at a loss or just using it as an expensive HLT.

 
Reply With Quote
Old 01-12-2012, 06:26 PM   #2
JonK331
 
JonK331's Avatar
Recipes 
 
Nov 2009
Fremont, CA
Posts: 2,099
Liked 33 Times on 33 Posts


Yup, taking it off every time is the way to go. that's what I do. Every single time I take it off and clean it with a tooth brush. The ball valve is not supposed to screw all the way down. Just wrap the threads with some plumbers tape to ensure a good seal.

 
Reply With Quote
Old 01-12-2012, 09:06 PM   #3
OneHoppyGuy
Recipes 
 
Nov 2009
Concord, CA
Posts: 1,666
Liked 44 Times on 36 Posts


It doesn't matter which of the 3 kettles it is if the issue is on the inside. You are boiling for 60 minutes right? It's everything that touches the wort after the boil kettle that matters.

 
Reply With Quote
Old 01-12-2012, 09:08 PM   #4
SpikeBrewing
Sponsor
HBT_SPONSOR.png
 
SpikeBrewing's Avatar
Recipes 
 
Jul 2011
Milwaukee, WI
Posts: 950
Liked 168 Times on 108 Posts


Quote:
Originally Posted by etho1416 View Post
I am really disappointed with this brewpot. I went with it instead of the megapot since it is made the USA, but I guess that does not mean that much any more.

Does anyone know if older version of this are welded on the inside? I swear I saw an odler one where the two holes are welded both on the outside and inside of the pot. Since mine is not welded on the inside, there is a really tight space where crud could hide and infiect my next beer.

Does anyone know how to get the ball valve all the way on? It won't screw all the way on, it feels like it is going to snap. It gets tight, but there is a few millimeters of exposed thread between the valve and the pot on the inside of the valve. This has me worried that crud will collect in there, be difficult to clean out, and ruin my next beer. Or I'll have to take the darn thing off and clean it every single time I use it.

I am serioulsy considering selling this thing at a loss or just using it as an expensive HLT.
Nobody would weld both sides of the coupler. If anything they might of sanitary welded the couplers. That will make the inside weld look like the outside weld. Without seeing a picture I can assume they didn't sanitary weld it. Honestly *in my opinion* a coupler doesn't need to be sanitary welded. I've sold 100's of welded kettles without problem. True, it doesn't look the best but you'll be boiling in it and using SanStar (or similar product) should kill everything.

As for the ball valve... The thread are tapered and you won't be able to tighten it flush. Teflon tape and hand tightening is more than enough. Anymore than that and you risk damaging the valve or kettle.

-Ben
__________________

 
Reply With Quote
Old 01-15-2012, 04:22 AM   #5
thargrav
Registered User
Recipes 
 
Dec 2009
Huntsville, Alabama
Posts: 821
Liked 38 Times on 35 Posts


Quote:
Originally Posted by etho1416 View Post
I am really disappointed with this brewpot. I went with it instead of the megapot since it is made the USA, but I guess that does not mean that much any more.

Does anyone know if older version of this are welded on the inside? I swear I saw an odler one where the two holes are welded both on the outside and inside of the pot. Since mine is not welded on the inside, there is a really tight space where crud could hide and infiect my next beer.

Does anyone know how to get the ball valve all the way on? It won't screw all the way on, it feels like it is going to snap. It gets tight, but there is a few millimeters of exposed thread between the valve and the pot on the inside of the valve. This has me worried that crud will collect in there, be difficult to clean out, and ruin my next beer. Or I'll have to take the darn thing off and clean it every single time I use it.

I am serioulsy considering selling this thing at a loss or just using it as an expensive HLT.
A brew pot welded only on the outside shoud be fine and if I had to chose between a inside weld or outside weld I would prefer a outside weld anyway because it looks better. If anything did happen to start growing in there the heat from the boil would kill it anyway.

 
Reply With Quote
Old 01-15-2012, 07:46 AM   #6
OneHoppyGuy
Recipes 
 
Nov 2009
Concord, CA
Posts: 1,666
Liked 44 Times on 36 Posts


Mega Pots are actually made by Update International in China. We swage and solder fittings from the inside they are clean and look great.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Polarware or Megapot? Eskimo Spy Equipment/Sanitation 26 01-07-2011 09:30 PM
Polarware or megapot??? balazs Equipment/Sanitation 3 05-29-2010 12:56 AM
Sanke Keg vs. PolarWare pot. bmickey Equipment/Sanitation 4 08-27-2009 01:14 PM
42qt pot and burner...any good??? rex Equipment/Sanitation 12 05-22-2009 11:37 PM
Polarware npt height egurney Equipment/Sanitation 1 03-25-2009 01:08 AM


Forum Jump