2362 PID / RTD Wiring help needed - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Electric Brewing > 2362 PID / RTD Wiring help needed

Reply
 
Thread Tools
Old 12-14-2011, 10:18 PM   #1
HellBentBrewCo
 
HellBentBrewCo's Avatar
Recipes 
 
Sep 2010
home, DE
Posts: 278
Liked 6 Times on 5 Posts



So I'm installing my PID and I'm stuck on wiring up the RTD receptacle. I soldered the red wires to pin's 1 and 3 and the white to pin 2 per Kal's website. Now I need to wire the receptacle to the PID and I can't figure out which pin is positive and which is negative. I found something that says the below but that doesn't make sense to me. Shouldn't 1 be a positive or negative and 2 be the ground?

1 Chassis ground (cable shield)
2 Positive polarity terminal for balanced audio circuits (aka "hot")
3 Negative polarity terminal for balanced circuits (aka "cold")[5]
__________________
Hell-Bent Brew Co. Blog

Hell-Bent Brew Co. on Facebook
Hell-Bent Brew Co. Gear Shirts, Steins and other awesome stuff

 
Reply With Quote
Old 12-14-2011, 10:27 PM   #2
iijakii
 
iijakii's Avatar
Recipes 
 
Jun 2010
Portland-ish, OR
Posts: 6,004
Liked 1791 Times on 1120 Posts


Not really sure what you're asking. Just connecting the RTD receptacle to the PID? Not really sure what you're asking about ground and what not for in reference to that.

For the 2362 white goes to 8, the reds go to 9 & 10 (doesn't matter which red goes where, you can even put them both to a single port on the RTD and use a jumper.)

Exact wording from the manual:

4.1.2 RTD sensor
For a three-wire RTD with standard DIN color code, the two red wires should
be connected to the terminals 9 and 10. The white wire should be connected to
terminal 8.
For a two-wire RTD, the wires should be connected to terminals 8 and 9. Jump
a wire between terminals 9 and 10.
Set controller input type, Inty, to P100 (1 resolution) or P10.0 (0.1 resolution)

 
Reply With Quote
Old 12-15-2011, 01:51 AM   #3
Lucky_Chicken
 
Lucky_Chicken's Avatar
Recipes 
 
Jul 2011
Bloomfield, IA
Posts: 795
Liked 37 Times on 27 Posts


Quote:
Originally Posted by iijakii View Post
For the 2362 white goes to 8, the reds go to 9 & 10 (doesn't matter which red goes where, you can even put them both to a single port on the RTD and use a jumper.)
you should not connect both reds to the same and jump them.. that is only if you have a 2 wire rtd. They are seperate wires to calibrate the resistance in the wire. One of them has a connection to the white (ground wire) at the other end it pulses to check the resistance on that loop the other one has the temperature resistor in the loop to ground the difference is the resistance in the temp sensor which is what you want to know because that translates into degrees.

 
Reply With Quote
Old 03-03-2013, 06:16 PM   #4
juic
Recipes 
 
Jan 2013
Great falls, Mt
Posts: 77


Did you wire the three syl-2362 in parallel like kal did?? If you did how did you wire the alarms together. Kal did it with with 2352 pids but I used 2362 and I'm not sure how to do the alarms????

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Auber 2362 wiring SpaceCoastBrew Electric Brewing 5 05-29-2014 04:33 AM
Wiring schematic for switchable 110v/220v control panel critique needed WPStrassburg Electric Brewing 15 11-19-2013 04:02 AM
Auber Ins 2362 help wadefisher Electric Brewing 0 10-13-2011 12:53 AM
Auber 2362 dboblitt Electric Brewing 2 03-15-2011 03:09 AM
Auber 2352 vs. 2362 paledragon Electric Brewing 0 12-19-2010 02:24 PM


Forum Jump