Question for users of cooler tuns - Home Brew Forums
Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Question for users of cooler tuns
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 12-11-2011, 05:35 AM   #1
Redpiper
Recipes 
 
Aug 2010
Los Angesles
Posts: 129


I just purchased a 10 gallon rubbermaid cooler from Lowe's. I tested 6 gallons in it at 162 degrees for an hour with blankets on top. It ended at 158. I've read that some fill the lid with foam to help heat loss. This may even be better?

My question is, for those of you who've gone that route, are you happy with results? Or should I return this cooler and look into one of those more expensive coolers that make claims about holding temp for long periods of time. If you had it to do all over again, what would you do?

Thanks in advance.



 
Reply With Quote
Old 12-11-2011, 06:04 AM   #2
Naggs
Recipes 
 
Jun 2011
Macomb, MI
Posts: 78
Liked 2 Times on 2 Posts


I'm no scientist, but I believe you'll get better heat retention when you have 10-13 pounds of grain in there as opposed to just hot water. The grain acts as its own insulation.


__________________
PRIMARY-Yorkshire Wheat, American Wheat
SECONDARY- none
BOTTLED-Pumpkin Ale, Christmas Ale, Citra Pale Ale, IPA, Cream Ale, Oatmeal Stout, Amber Ale, Saison, Orange Kolsch, Galaxy IPA

 
Reply With Quote
Old 12-11-2011, 06:08 AM   #3
muthafuggle
Recipes 
 
Jan 2010
, Utah
Posts: 185
Liked 11 Times on 10 Posts


Quote:
Originally Posted by Naggs
I'm no scientist, but I believe you'll get better heat retention when you have 10-13 pounds of grain in there as opposed to just hot water. The grain acts as its own insulation.
+1 to this. I loose maybe 1 or 2 degrees max on a 60 minute mash with my 10 gallon igloo. Also, pre-heating the tun helps a lot.
__________________
"Fat, drunk and stupid is no way to go through life, son"

Primary: 90 Shilling
Secondary: Empty
Bottled: Out of beer... need to brew more.
Kegged: STILL out of beer.

 
Reply With Quote
Old 12-11-2011, 06:13 AM   #4
rednekhippiemotrcyclfreak
Recipes 
 
Apr 2008
Tennessee
Posts: 194
Liked 3 Times on 3 Posts


+1 What Naggs said. I usually start out with near boiling water in my cooler and wait for it to drop to the strike temp. This can take an hour but can be speeded up by opening the lid and stirring the water. The idea is to get the cooler well preheated (oxymoron). Once you dough in, the mash will hold within 1 or 2 degrees for a full hour with the lid closed. Don't forget to factor in the temp of your dry crushed grain to end up with the correct mash temp. Sorry muthafuggle, you beat me to it.

Oh yeah, mine is a cheap cooler. On cold days I'll wrap a blanket around it. It works fine.

 
Reply With Quote
Old 12-11-2011, 03:19 PM   #5
Boodlemania
Recipes 
 
Jul 2008
East TN
Posts: 593
Liked 5 Times on 4 Posts


Gotta preheat that sucker. I preheat mine with 180F water for 30 minutes, then if it's still above strike temp, I'll "stir it down" or even add a touch of cold water.

9 out of 10 brews, I loose less than a degree.
__________________
- CStone

 
Reply With Quote
Old 12-11-2011, 03:25 PM   #6
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 68,504
Liked 7365 Times on 5207 Posts


Quote:
Originally Posted by Boodlemania View Post
Gotta preheat that sucker. I preheat mine with 180F water for 30 minutes, then if it's still above strike temp, I'll "stir it down" or even add a touch of cold water.

9 out of 10 brews, I loose less than a degree.
Yep, me too. Add 180 degree water and let sit while you crush your grain. You should be at strike temp. If you're in a hurry, you can preheat with one gallon of hot water and cover it for 10 minutes, then drain. But I like adding all of my strike water and letting the temp come down to strike temps- it is easy, and it seems to really preheat the MLT perfectly. It will only lose a degree or so over an hour.

As was mentioned, the grain also helps insulate and unless you're doing a tiny grain bill (under 7 pounds), you won't need to worry about the headspace in there.
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 12-11-2011, 03:32 PM   #7
acuenca
Recipes 
 
Jul 2011
Gainesville, Fl
Posts: 366
Liked 8 Times on 8 Posts


+10 to the suggestion for preheating the mash tun... I was losing 4-6 degrees initially until I figured that out...

 
Reply With Quote
Old 12-11-2011, 06:00 PM   #8
Redpiper
Recipes 
 
Aug 2010
Los Angesles
Posts: 129

Thanks for the replies. Here's a little additional info.

My actual test first involved 3 gallons and no blanket and I lost over 15 degrees. I then reheated the 3 gallons to 165, closed the lid. Heated another 3 gallons and added that and then blankets. So in a sense I think it was preheated? But maybe not high enough. Loss was 5 degrees.

The Rubbermaid coolers don't melt/warp with boiling water?

I also noticed the sides weren't warm but the top was. Heat rises, so would grain slow down heat loss from the top? This is what made me wonder about foam in the lid to help.

 
Reply With Quote
Old 12-11-2011, 06:08 PM   #9
seabass07
Recipes 
 
Apr 2011
Brothell
Posts: 1,249
Liked 121 Times on 91 Posts


+another1 I just overshoot my strike temp by 10F and let it sit until I get to where I want it.

I did pour 5 gallons of boiling water into my cooler one time when I wasn't paying attention to the strike water temp. It didn't warp or anything. Even the food grade buckets can take boiling water. I wouldn't move them though...
__________________
Fermenter 1: Beer
Fermenter 2: Beer
Fermenter 3: Beer
Fermenter 4: Beer

 
Reply With Quote
Old 12-11-2011, 06:22 PM   #10
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 68,504
Liked 7365 Times on 5207 Posts


Yes, they will warp/crack with boiling water. I have proof. But you're totally safe with 180 degree water.


__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Pumps and mash tuns metalpysko All Grain & Partial Mash Brewing 13 09-04-2011 05:04 AM
Protein rest techniques for cooler mash tuns Randar All Grain & Partial Mash Brewing 6 03-10-2010 10:10 PM
Question for HERMS users McCuckerson All Grain & Partial Mash Brewing 13 02-11-2010 03:04 AM
Question for sanky tun users BrothersBrewing All Grain & Partial Mash Brewing 11 07-29-2009 04:14 PM
Suggestions for Mash Tuns Jsta Porter All Grain & Partial Mash Brewing 10 10-24-2007 07:32 AM


Forum Jump