2 PID brew panel used for fermentor control when not brewing - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Electric Brewing > 2 PID brew panel used for fermentor control when not brewing

Reply
 
Thread Tools
Old 12-08-2011, 05:51 PM   #1
t_met
Recipes 
 
Apr 2009
Posts: 97
Liked 10 Times on 5 Posts



I did a search but couldn't find exactly what I'm thinking. I'm in the process of figuring out my partial e-HERMS brewery. I think my brewery panel will have 2 PIDS, one timer, and alarm. Nothing fancy. The HEX would be a standalone unit, not a part of HLT. Because of this smaller HEX, I would only use 120v.

My thought was after a brew session, I could unplug my HEX, pumps, etc from the control panel and move it to where my fermentation fridge is. Use the same PIDs to control the cold/hot of the fridge.

Is this feasible? I'm sure it is. A better question is if anyone has done this with PID. I read people using BCS in this way, but I think I want to go down the PID path.

I figured, I only brew so often. Often my last batch has completed fermentation before I start my next one.

 
Reply With Quote
Old 12-08-2011, 06:05 PM   #2
Bsquared
HBT_LIFETIMESUPPORTER.png
 
Bsquared's Avatar
Recipes 
 
Oct 2006
San Diego
Posts: 1,850
Liked 66 Times on 59 Posts


I tried using a PID through an SSR for fermentation control a while back. It will not work. The PID rapidly cycles the SSR on and off when it is near its set temp, so it is never able to get the compressor on the fridge to turn on when it is near your set temp. Though you could use one of the alarms on the PID to control the fridge, if the relay on the PID can handle the amperage of running the compressor.

This is one reason I went the BCS route.

 
Reply With Quote
Old 12-08-2011, 06:22 PM   #3
t_met
Recipes 
 
Apr 2009
Posts: 97
Liked 10 Times on 5 Posts


Quote:
Originally Posted by Bsquared View Post
I tried using a PID through an SSR for fermentation control a while back. It will not work. The PID rapidly cycles the SSR on and off when it is near its set temp, so it is never able to get the compressor on the fridge to turn on when it is near your set temp. Though you could use one of the alarms on the PID to control the fridge, if the relay on the PID can handle the amperage of running the compressor.

This is one reason I went the BCS route.

It maybe the PID you're using, while searching on this topic I found this thread.
http://www.homebrewtalk.com/f51/love...7/#post1646095

The poster said you could change some of the settings to allow a wider temperature range and keep the power on for 60 seconds to reduce the cycling. So I didn't think the limitation was the PID. But I haven't played with one so it maybe overkill for this application, but I figured if I could put it to work while not brewing.

 
Reply With Quote
Old 12-08-2011, 06:38 PM   #4
Bsquared
HBT_LIFETIMESUPPORTER.png
 
Bsquared's Avatar
Recipes 
 
Oct 2006
San Diego
Posts: 1,850
Liked 66 Times on 59 Posts


I never tried that with the PID I bought, I ended up running my freezer through the High alarm relay on my PID, and put the SSR in to my control box for the brewery.

It looks like that would work, though you would most likely want to reprogram the power settings when you brew, or when you ferment. I might also be concerned about (if I was reading coad rages post correctly) that for controlling the fermenter the PID would be cycling on 60sec off 60sec, this might be rough on the compressor.

I think though you could set it up so the PID SSR runs the brewing side, and you run your fermenter through the High alarm of the PID. You would just need to turn off the fridge during brewing, and move the temp probe. Or rig up a selector switch that can switch between a probe in the fermenters or for brewing, and switch off the fridge during brewing.

 
Reply With Quote
Old 12-08-2011, 07:32 PM   #5
Walker
I use secondaries. :p
HBT_LIFETIMESUPPORTER.png
 
Walker's Avatar
Recipes 
 
Sep 2005
Cary, NC
Posts: 10,987
Liked 101 Times on 89 Posts


You can use a PID for controlling ferm chamber. You just have to put the PID into a different mode (on/off mode instead of PID mode) to avoid the rapid cycling that bsquared talks about.
__________________
Ground Fault Brewing Co.

 
Reply With Quote
Old 12-08-2011, 07:37 PM   #6
t_met
Recipes 
 
Apr 2009
Posts: 97
Liked 10 Times on 5 Posts


I see what you're saying with the alarm.

Quote:
Originally Posted by Bsquared View Post
I think though you could set it up so the PID SSR runs the brewing side, and you run your fermenter through the High alarm of the PID. You would just need to turn off the fridge during brewing, and move the temp probe. Or rig up a selector switch that can switch between a probe in the fermenters or for brewing, and switch off the fridge during brewing.
The fridge is in a separate place in my house. I was thinking this control unit would attach to my brew stand (still in planning phase). After the brew detach it (and plugs & temperature readings) and hang it on the wall near the fridge and attach temp probe & plugs.

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Control Panel VS Computer Bru Electric Brewing 14 01-26-2012 02:35 AM
Mounting spa panel guts in control panel kevink Electric Brewing 7 08-20-2011 02:31 AM
Electric brewing without a Control Panel?? staab016 Electric Brewing 42 06-20-2011 07:04 AM
Control panel stokems Electric Brewing 1 06-19-2011 10:56 PM
Toolbox control panel gclay Electric Brewing 1 04-11-2011 07:38 PM


Forum Jump