My E-HERMS Brew Rig Thread - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Electric Brewing > My E-HERMS Brew Rig Thread

Reply
 
Thread Tools
Old 12-08-2011, 12:39 AM   #1
moparx12
Recipes 
 
Apr 2010
charlotte
Posts: 193


Hey guys,

I figured i would post up about some of the progress i have been making on my brew rig. It's going somewhat slow partially due to money and a little due to laziness.

Anyway, I have a rough CAD model made for structural portion as it is designed so far:





That is just part of the work i have been doing. A lot more to come with control panel and stuff. I wanted it to look different than most other rigs, and it ended up looking like a sawhorse. I still think it looks good though.

All of the plumbing will be hard lines with disconnects on the sides and backs of all 3 vessels. That way i can unhook the turnbuckles and tip them forward to rinse them out.

Do you guys think its at a good height? the top of the kegs are at ~ 53"



 
Reply With Quote
Old 12-08-2011, 01:05 AM   #2
phoenixs4r
Recipes 
 
Jun 2011
Hayward, California
Posts: 1,515
Liked 56 Times on 51 Posts


Are those shocks?



 
Reply With Quote
Old 12-08-2011, 01:25 AM   #3
moparx12
Recipes 
 
Apr 2010
charlotte
Posts: 193

no those are turnbuckles. i will use them to tighten the kegs down to the crossbar you see in the third pic. they will have quick disconnect pins for when i want to tip the kegs forward.

 
Reply With Quote
Old 12-08-2011, 01:53 AM   #4
phoenixs4r
Recipes 
 
Jun 2011
Hayward, California
Posts: 1,515
Liked 56 Times on 51 Posts


Neat. Never thought if that. Might steal that from you when I build mine

 
Reply With Quote
Old 12-08-2011, 04:29 AM   #5
moparx12
Recipes 
 
Apr 2010
charlotte
Posts: 193

no problem.

More to come btw!

 
Reply With Quote
Old 12-08-2011, 12:49 PM   #6
Lucky_Chicken
Recipes 
 
Jul 2011
Bloomfield, IA
Posts: 795
Liked 37 Times on 27 Posts


nice cad work... now if we can just convert you to the dark side and use ProE lol

 
Reply With Quote
Old 12-08-2011, 02:10 PM   #7
moparx12
Recipes 
 
Apr 2010
charlotte
Posts: 193

lol. that is the dark side! I used ProE some in college but definately prefer solidworks.

 
Reply With Quote
Old 12-08-2011, 03:26 PM   #8
JKoravos
Recipes 
 
Jul 2009
Chelmsford, MA
Posts: 1,203
Liked 73 Times on 54 Posts


Why the turnbuckles? Do the platforms really need to be tightened down? A spring loaded pin should be enough to hold them in place, I would think. The turnbuckles strike me as an added bit of complexity for little benefit.

 
Reply With Quote
Old 12-08-2011, 07:11 PM   #9
moparx12
Recipes 
 
Apr 2010
charlotte
Posts: 193

yes, the turnbuckles are over-kill - but aren't most brew rig designs you see on here? i made it that way so that i would have no "slop" in the pinned connection that would allow the keg to wiggle. I figured it would allow me to preload it slightly to eliminate any movement at all.

Maybe im not thinking of the same type of spring loaded pin you are...

 
Reply With Quote
Old 12-08-2011, 07:21 PM   #10
JKoravos
Recipes 
 
Jul 2009
Chelmsford, MA
Posts: 1,203
Liked 73 Times on 54 Posts


Quote:
Originally Posted by moparx12 View Post
yes, the turnbuckles are over-kill - but aren't most brew rig designs you see on here? i made it that way so that i would have no "slop" in the pinned connection that would allow the keg to wiggle. I figured it would allow me to preload it slightly to eliminate any movement at all.

Maybe im not thinking of the same type of spring loaded pin you are...

I would offset the pivot point towards the front of the vessel, that way you have the weight of the kettle providing some stability. Next I would put a relatively stiff piece of rubber on the cross beam to damp the contact between the two steel pieces. The pin would just hold it in place, just like you've drawn for the turnbuckle end mounts, it doesn't need to be spring loaded (I was thinking of a 'spring plunger'). If you position it right, you could pin it in place with some compression in the rubber, which would prevent movement and vibration. I guess if you want them REALLY stable, the turnbuckle will work for that purpose.



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Aces! Another HERMS Build thread! Verloc5150 Brew Stands 7 03-22-2012 05:22 PM
HERMS Brew Rig Beginnings moparx12 Brew Stands 1 10-29-2011 01:49 AM
Help finding specific herms build thread SenorWanderer Brew Stands 2 10-21-2010 01:34 AM
Pol's Electric HERMS thread compilation... The Pol Brew Stands 9 11-03-2009 02:40 AM
The Evil Gnome HERMS Brew Rig EvilGnome6 Brew Stands 20 07-08-2009 09:21 PM


Forum Jump