Cost Savings in Electric? - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Electric Brewing > Cost Savings in Electric?

Reply
 
Thread Tools
Old 11-10-2011, 05:21 PM   #1
BucksPA
Recipes 
 
Dec 2009
Bucks, PA
Posts: 447
Liked 5 Times on 5 Posts



My Brutus 10 clone was can be viewed in my signature runs off of propane. I typically get 1.5 seperate brew sessions for each Lowe's purchased propane tank. Each tank costs $20 and each brew session is used for heating up sparge water (9-10 gallons), strike water (4-7 gallons), and used for a vigorous boil at about 11% evaporation rate per hour, typically 60 minute boils.

I brew a lot and am have 3 tanks on hand, but am spending so much on propane I wonder if there are cost savings with electric versus propane.

Can an electric setup be used for less than approximately $13-15 per session?

If you really want to get technical, mr electric runs 10 cents kw.


__________________
40 Gallons brewed in 2013....and counting
33 Gallons brewed in 2012
159 Gallons brewed in 2011

My Brutus 10

 
Reply With Quote
Old 11-10-2011, 05:52 PM   #2
hatfieldenator
Recipes 
 
Sep 2010
Posts: 493
Liked 17 Times on 14 Posts


In my opinion electricity has got to be cheaper than all that propane. If you wanted to do a rough estimate on math just assume it takes 30 minutes to heat up your system, 60 mins for a mash, another 20-30 to heat up to boiling, than 60 minutes of boiling. Assume you're using 22amps at 240V's that entire time and you can try to estimate costs.
If I'm doing my math right, using an online calculator, thats 5280Watts of energy for 3 hours at 10cents per kwh would add up to about $1.58 in electricity charges for a 3 hour brew session. Of course this will vary greatly with how long it actually takes depending on the amount of water you're heating and boiling and how cold the water is to start. Even if it takes you 4 hours you're still only talking $2.11

If anyone else wants to chime in here and do their own calculations it would be helpful to see if others agree with this very rough estimate. But, it looks like it would be much cheaper overall.

http://www.webmath.com/kwh.html
http://www.supercircuits.com/resourc...Amps-Converter



 
Reply With Quote
Old 11-10-2011, 06:09 PM   #3
thughes
HBT_SUPPORTER.png
Recipes 
 
Jan 2010
Rochester
Posts: 702
Liked 52 Times on 49 Posts


Less than $1.00, according to this thread:

http://www.homebrewtalk.com/f170/40-...20/index2.html

I was getting @ 3-4 brew sessions per tank before I went electric recently. I've since done 5 batches and love not having to worry about propane supply.
__________________
nurture my pig

 
Reply With Quote
Old 11-10-2011, 06:10 PM   #4
jusware
Recipes 
 
Jun 2009
helena, Montana
Posts: 140
Liked 5 Times on 4 Posts


I have a RIMs system similar to www.theelectricbrewery.com. I have a panel mounted amp meter. I would agree with the analysis above. However, with PID control rarely are the elements running at 100%. Even though my brew day is approx 3 hrs, the only time the elements are at 100% is during the intial strike water warming, and warming up the bk to boil. My rims tube once it hits the mash temp pretty stays < 10% PID. I set my BK down to 60% PID once I hit a boil. With all that in mind I would take the 1.58$ above and drop it well below 1$.

 
Reply With Quote
Old 11-10-2011, 06:17 PM   #5
shortyjacobs
Recipes 
 
Aug 2009
Twin Cities, MN
Posts: 2,509
Liked 33 Times on 33 Posts


Math looks good, I'd say you're even way overestimating since most E-rigs don't run wide open at 22-23 amps for most of the time. For most of the mash you're at 10-20% power to maintain temps, (could be a bit less or more depending on insulation), and for boil you're at 50-75% depending on how vigorous a boil and again insulation.

The other way to look at it is: You will need to raise 15 gallons of water from 10C to 100C, and boil 1.5 gallons of it into steam.

15 gallons of water is 56.8 kg. Water's specific heat is 4.18 kJ/kg/K, you are going from 10 C to 100C which is 90K delta. So you need 21,368 kJ.

Latent heat of vaporization is 2260 kJ/kg, 1.5 gallons of water weighs 5.68 kg. Energy to boil is 12,836 kJ.

So total is 34,204 kJ. Assume 80% efficiency to account for heat loss, you're at 42,759 kJ. One watt is 1 J/s. One kW is 1 kJ/s. so you need 42,759 kW*s, divide by 3600 seconds in an hour and you need 11.88 kW*h. At $0.10/kW*h, that's $1.19.
__________________
Itchy Dog Brewery.

(As of 10-24-2011)
Primary - Steppe 112 PA, 2x Monday RyePA
Aging - None :-(
On tap - Big Dog, Apfelwein, Steppe 112 PA

My invisible AG sculpture, with no actual sculpture and a tiny footprint.
My Kegerator goes offroading!
My Coors Home Draft dispenser for boating/beering on the go.

 
Reply With Quote
Old 11-10-2011, 06:32 PM   #6
sonex
Recipes 
 
Jun 2011
dillsburg, pa
Posts: 389
Liked 12 Times on 12 Posts


electricity without argument is cheaper than propane. The cost of your system depending on complexity can negate the savings. I built my system b/c thats the system I wanted and would never go back to propane. Cost savings on fuel is not in my oppinion alone the best reason to go electric. except for inexpensive heat sticks the cost of equipment would eat up the fuel savings.

 
Reply With Quote
Old 11-10-2011, 06:46 PM   #7
thughes
HBT_SUPPORTER.png
Recipes 
 
Jan 2010
Rochester
Posts: 702
Liked 52 Times on 49 Posts


Quote:
Originally Posted by shortyjacobs View Post
Math looks good, I'd say you're even way overestimating since most E-rigs don't run wide open at 22-23 amps for most of the time. For most of the mash you're at 10-20% power to maintain temps, (could be a bit less or more depending on insulation), and for boil you're at 50-75% depending on how vigorous a boil and again insulation.

The other way to look at it is: You will need to raise 15 gallons of water from 10C to 100C, and boil 1.5 gallons of it into steam.

15 gallons of water is 56.8 kg. Water's specific heat is 4.18 kJ/kg/K, you are going from 10 C to 100C which is 90K delta. So you need 21,368 kJ.

Latent heat of vaporization is 2260 kJ/kg, 1.5 gallons of water weighs 5.68 kg. Energy to boil is 12,836 kJ.

So total is 34,204 kJ. Assume 80% efficiency to account for heat loss, you're at 42,759 kJ. One watt is 1 J/s. One kW is 1 kJ/s. so you need 42,759 kW*s, divide by 3600 seconds in an hour and you need 11.88 kW*h. At $0.10/kW*h, that's $1.19.
I think my head just exploded.
__________________
nurture my pig

joeybeer Likes This 
Reply With Quote
Old 11-10-2011, 06:57 PM   #8
zeno27
Recipes 
 
Feb 2011
ithaca, NY
Posts: 101
Liked 3 Times on 3 Posts


Quote:
Originally Posted by shortyjacobs View Post
The other way to look at it is: You will need to raise 15 gallons of water from 10C to 100C, and boil 1.5 gallons of it into steam.
since I love nit-picking, I'll just add that you won't raise all 15 gallons to 100C: some will be absorbed by the grain. But otherwise, that's exactly how I would calculate the cost.

 
Reply With Quote
Old 11-10-2011, 08:36 PM   #9
BucksPA
Recipes 
 
Dec 2009
Bucks, PA
Posts: 447
Liked 5 Times on 5 Posts


my system cost $2300 to build from the groun up. I dont care though, because hobbies aren't cheap. If i wanted to brew beer to save money, I'd be brewing corn and rice beers. However, when it comes to down to brew day (twice a month), I'd love to get that cost down to $60 for 10 gallons versus $80.

So what you guys are telling me is great news. The cost to build on the front end doesn't matter as much as the cost on the back end every time i brew.

That's a big difference $13 per session versus $1 or $2 max.

thanks.
__________________
40 Gallons brewed in 2013....and counting
33 Gallons brewed in 2012
159 Gallons brewed in 2011

My Brutus 10

 
Reply With Quote
Old 11-10-2011, 08:58 PM   #10
shortyjacobs
Recipes 
 
Aug 2009
Twin Cities, MN
Posts: 2,509
Liked 33 Times on 33 Posts


Quote:
Originally Posted by zeno27 View Post
since I love nit-picking, I'll just add that you won't raise all 15 gallons to 100C: some will be absorbed by the grain. But otherwise, that's exactly how I would calculate the cost.
lol, I knew someone would pick up on that.

See, trick is, you're also having to heat grain up from ~10C to whatever the hell mash temp is in C....and I didn't feel like figuring THAT bit out. (Specific heat of barley, WTF? ). I suppose I could have figured it out by knowing how much, say, 25 lbs of 50F grain will drop the strike water temp, but that was too much work. I figured that by just saying I'm heating everything to 100C, I'll capture the absorption/grain heating bit under the umbrella .


__________________
Itchy Dog Brewery.

(As of 10-24-2011)
Primary - Steppe 112 PA, 2x Monday RyePA
Aging - None :-(
On tap - Big Dog, Apfelwein, Steppe 112 PA

My invisible AG sculpture, with no actual sculpture and a tiny footprint.
My Kegerator goes offroading!
My Coors Home Draft dispenser for boating/beering on the go.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Electric vs Natural Gas Homebrew Setup Cost TheBrewBros Electric Brewing 26 08-30-2013 04:02 AM
My Super Mini Single Element 120V ULC (ultra low cost) Electric Setup ryclo Electric Brewing 28 07-20-2011 01:36 AM
I want a electric set up Cwetherford Electric Brewing 9 07-12-2011 06:46 PM
looking at using electric, I could use a lot of help. killian Electric Brewing 21 07-08-2011 07:53 PM
How Much Electric mykayel Electric Brewing 5 06-28-2011 11:29 PM


Forum Jump