Danby DAR125SLDD Kegerator Build - Page 8 - Home Brew Forums
Home Brew Forums > Home Brewing Beer > DIY Projects > Kegerators & Keezers > Danby DAR125SLDD Kegerator Build

Reply
 
Thread Tools
Old 12-15-2012, 02:54 AM   #71
FatTonyTCL
Recipes 
 
Dec 2012
Posts: 6


Quote:
Originally Posted by Stephen_mc View Post
What did you use to cut the white board? Sorry about all the questions. I'm light on tools in my apt.
I used painters tape and a circle saw. I think any saw would work though just make sure you keep your board from vibrating too much. The excess parts without the painters tape chipped a bit so thats a step I wouldn't recommend skipping.
This pic shows the white board after it was cut.



 
Reply With Quote
Old 12-15-2012, 09:26 PM   #72
opusx11
Recipes 
 
Aug 2009
Edmonton, Canada
Posts: 95
Liked 3 Times on 3 Posts


DeNomad, I finally found the fridge at the Winterburn Costco, same model. I picked one up today, but am just going to ensure it works fully before I start destroying it. I think I'm in the same boat as the others though where the door does not have screws. I'll have to see if someone I know has a dremel or something to help get it off.



 
Reply With Quote
Old 12-27-2012, 11:05 PM   #73
donjonson
Recipes 
 
Nov 2010
Tampa, FL
Posts: 320
Liked 1 Times on 1 Posts


Quote:
Originally Posted by DeNomad View Post
No. If you look at the photos the kegs almost reach the end of the fridge, maybe 1-2" from the edge. The drink holders on the door would bump into the kegs for sure.
I am able to get a single ball lock keg in this fridge without any modifications to the door. the only thing I had to do was remove the removable shelving from the opening side of the door. 1 keg fits in just fine.

On that note, has anyone with this fridge been able to get a ball lock keg + 1 commercial sixth keg in there? would that fit? a ball lock has 8.5" diameter and according to a web resource a sixth keg has a 9.25" diameter.

 
Reply With Quote
Old 12-28-2012, 11:19 PM   #74
donjonson
Recipes 
 
Nov 2010
Tampa, FL
Posts: 320
Liked 1 Times on 1 Posts


Quote:
Originally Posted by DeNomad View Post
I don't think so. You *might* be able to squeeze an 11" diameter bucket. Here are the dimensions I measured when I was choosing between ball lock and pin lock kegs. Since the pin locks wouldn't fit as shown below I chose ball lock.

how did you measure the inner dimensions of the fridge with such accuracy?

 
Reply With Quote
Old 12-29-2012, 02:07 PM   #75
wsender
Recipes 
 
May 2011
Rochester, NY
Posts: 50
Liked 5 Times on 3 Posts


Quote:
Originally Posted by donjonson View Post
how did you measure the inner dimensions of the fridge with such accuracy?
Yes, thousands of an inch is pretty precise...

 
Reply With Quote
Old 12-29-2012, 05:39 PM   #76
donjonson
Recipes 
 
Nov 2010
Tampa, FL
Posts: 320
Liked 1 Times on 1 Posts


Quote:
Originally Posted by henryfdez View Post
You have to remove the plastic mold on the inside door to be able to fit any kegs....if you do remove it (which is super easy and doesnt damage the fridge in any way) you will be able to fit up to 2 ball lock kegs, or one ball lock and one pin lock. If you only put one ball lock in there you would still have half of the fridge space for other stuff. Ive had it for some time now and I can honestly say its an awesome fridge.

Cheers!
how much wiggle room do you have with one ball lock and one pin lock? I am thinking about putting in a ball lock and a sixth commercial keg. the ball lock is 8.5" diameter and from what I gather online the sixth is 9.25" diameter. just .25 more than a pin lock do you think there is enough room in there for what I am trying to do?

 
Reply With Quote
Old 01-15-2013, 01:08 PM   #77
DeNomad
Recipes 
 
Aug 2010
Edmonton
Posts: 304
Liked 5 Times on 4 Posts


Quote:
Originally Posted by donjonson View Post
how did you measure the inner dimensions of the fridge with such accuracy?
I used a tape measure and a pair of calipers. Measured the width of the outside, then calipers on the wall thickness. Inner width = Outside width - 2*thickness. I forget how I measured the length but I likely did something similar. The gray dimensions are reference dimensions calculated by the CAD program.
__________________
What's on tap... I don't even keep track anymore.

 
Reply With Quote
Old 01-15-2013, 01:15 PM   #78
DeNomad
Recipes 
 
Aug 2010
Edmonton
Posts: 304
Liked 5 Times on 4 Posts


Quote:
Originally Posted by donjonson View Post
how much wiggle room do you have with one ball lock and one pin lock? I am thinking about putting in a ball lock and a sixth commercial keg. the ball lock is 8.5" diameter and from what I gather online the sixth is 9.25" diameter. just .25 more than a pin lock do you think there is enough room in there for what I am trying to do?

My recommendation is to cut out circles of cardboard of the correct diameter and toss them in there, see what you think. Be aware of the plastic tabs where the shelves sit since that is the tightest part of the fridge. Mark 3/4" away from the side wall, that is where the plastic tabs extend too.

Off the top of my head...
1 ball lock + 1 pin lock: Probably would need to cut out the bits of plastic the shelves sit on to make this work. 2 ball locks are very tight already.

1 ball lock + 1 commercial keg: Definitely need to cut out the bits of plastic the shelves sit on. No guarantee here. Kinda doubt it.
__________________
What's on tap... I don't even keep track anymore.

 
Reply With Quote
Old 03-07-2013, 02:26 AM   #79
nlanzillo
Recipes 
 
Mar 2013
Posts: 3

I just purchased this model, but can't seem to find any screws along the door. Pulled the gasket back, but zero screws. Any suggestions?

 
Reply With Quote
Old 03-07-2013, 02:33 AM   #80
BansheeRider
HBT_SUPPORTER.png
 
BansheeRider's Avatar
Recipes 
 
Dec 2012
Posts: 1,514
Liked 102 Times on 93 Posts


Quote:
Originally Posted by nlanzillo View Post
I just purchased this model, but can't seem to find any screws along the door. Pulled the gasket back, but zero screws. Any suggestions?
Danby now glues the shelving to the door and insulating foam. You have to cut around with a dremel or just cut the shelving out.


__________________
Good judgement comes from experience, experience comes from bad judgement.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Kegerator Conversion with Danby DAR440BL? GloHoppa Kegerators & Keezers 178 10-07-2014 01:53 AM
Danby 10.2 (DCFM289WDD) Keezer Build Thread jcaudill Kegerators & Keezers 91 07-17-2014 09:16 PM
If You Have To Build A Kegerator All Over Again ScottishPete Kegerators & Keezers 15 05-06-2010 07:03 AM
Kegerator Build wraith264 Kegerators & Keezers 1 10-06-2009 02:34 PM
small Danby keezer build MTHarrington Kegerators & Keezers 6 05-16-2009 03:06 PM


Forum Jump