best HERMs coil location? - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > best HERMs coil location?

Reply
 
Thread Tools
Old 07-29-2011, 07:22 PM   #1
slakwhere
Recipes 
 
Dec 2009
Salt Lake City, Utah
Posts: 764
Liked 21 Times on 20 Posts



so i have a 50' 1/2" coil that i use as an IC, but i'm contemplating taking the old 25' IC and installing it into the HLT as a HERMS coil. the question is: where to put it in the HLT?

i assume i want to mount it as low as i can to minimize the amount of water needed in the HLT. that means drilling a couple holes and some compression fittings near the bottom.

output on the bottom and intake on the top so that it gravity drains, right?

ball lock on the bottom or top? needed at all?

should the 2 connectors be vertically aligned? is there some reason i'd want them offset?

anything else i gotta know before i punch holes?

 
Reply With Quote
Old 07-29-2011, 08:05 PM   #2
JuanMoore
Recipes 
 
Oct 2009
The Old Pueblo
Posts: 21,896
Liked 3682 Times on 3504 Posts


I installed mine in a lid. This allows a lot of versilility, like being able to also use it as an IC, but does make it harder to drain. I chill by running the wort through the HEX with the HLT filled with tap water to get down to ~120F. While that's going I throw a couple bags of ice and a little water in the MLT. I then complete the chilling by moving the HEX coil to the MLT. I also installed a T in the output side of the HEX for a thermowell to monitor exit temps both during the mash and when chilling. By ball lock do you mean ball valve? If so you don't really need one.

 
Reply With Quote
Old 07-29-2011, 08:11 PM   #3
slakwhere
Recipes 
 
Dec 2009
Salt Lake City, Utah
Posts: 764
Liked 21 Times on 20 Posts


i'm keeping the 50' as an IC, so the 25' will be strictly for the HLT as a HERMs.

 
Reply With Quote
Old 07-29-2011, 09:05 PM   #4
resslerk
Recipes 
 
Dec 2009
SE Wisconsin
Posts: 59
Liked 1 Times on 1 Posts


I put mine in the bottom, gravity drain as you described, put a ball valve on the intake (top) only, and offset them by 90 degrees. Doing so allows easier access when installing (removing).


 
Reply With Quote
Old 07-29-2011, 09:33 PM   #5
slakwhere
Recipes 
 
Dec 2009
Salt Lake City, Utah
Posts: 764
Liked 21 Times on 20 Posts


resslerk, what's the ball valve for? my gut says i need one but my brain doesn't know why...

 
Reply With Quote
Old 07-29-2011, 09:50 PM   #6
slakwhere
Recipes 
 
Dec 2009
Salt Lake City, Utah
Posts: 764
Liked 21 Times on 20 Posts


whoah, gut check... 2 compression fittings @ 20 each plus the camlock connectors plus the full couplings. this just got more expensive than i was anticipating.

http://www.bargainfittings.com/index...product_id=170
http://www.bargainfittings.com/index...&product_id=49
http://www.bargainfittings.com/index...product_id=133

maybe i'll just keep my 50' IC and swap it from HLT as a herms to BK as an IC.

 
Reply With Quote
Old 07-29-2011, 10:17 PM   #7
jsguitar
HBT_SUPPORTER.png
 
jsguitar's Avatar
Recipes 
 
May 2011
Overland Park, KS
Posts: 1,185
Liked 126 Times on 99 Posts


Was just looking at those exact things yesterday and had the same reaction. The SS compression fittings are cheaper by a little bit elsewhere but by the time you add shipping from other places it's pretty much a wash. I wonder if anyone has a considerably cheaper source for those?

 
Reply With Quote
Old 07-30-2011, 01:47 AM   #8
JuanMoore
Recipes 
 
Oct 2009
The Old Pueblo
Posts: 21,896
Liked 3682 Times on 3504 Posts


If your HEX coil is copper, why the need for expensive SS fittings?

 
Reply With Quote
Old 07-30-2011, 06:50 AM   #9
slakwhere
Recipes 
 
Dec 2009
Salt Lake City, Utah
Posts: 764
Liked 21 Times on 20 Posts


guess it didn't occur to me to use anything but stainless... McMaster has brass ones for $11 + shipping, doesn't seem like that much savings.

just didn't really occur to me how quickly fittings add up. just did some math about all my BargainFittings orders and it's a ridiculous sum of money :|

 
Reply With Quote
Old 07-30-2011, 07:23 AM   #10
JuanMoore
Recipes 
 
Oct 2009
The Old Pueblo
Posts: 21,896
Liked 3682 Times on 3504 Posts


I'm pretty sure I picked mine up for <$5 ea at home depot. They look just like the ones in the pic above. The cost of fittings adds up fast no matter what. Even though I skimped and used a lot of brass, copper, and aluminum, the fittings were still a large portion of the cost of my HERMS.

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
HERMS HEX coil Drake371 DIY Projects 9 12-23-2013 03:06 AM
HERMS coil in Keggle jcalisi Brew Stands 6 03-08-2011 04:23 AM
IC to HERMS coil? Cpt_Kirks Brew Stands 11 01-12-2011 05:48 AM
Herms Coil Help rj_hockey Brew Stands 3 03-13-2009 01:11 PM
HERMS HEX coil? Gumbys_Brew Brew Stands 9 02-27-2009 10:18 PM


Forum Jump