Re-Bending a Copper Wort Chiller - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Re-Bending a Copper Wort Chiller

Reply
 
Thread Tools
Old 03-23-2007, 05:32 PM   #1
weetodd
Recipes 
 
Oct 2006
Seattle. WA
Posts: 197
Liked 1 Times on 1 Posts



I was able to obtain a standard immersion chiller from a dude that was getting rid of his old stuff for a very decent price. Seeing the price of copper these days I jumped on it because it was a pretty good deal. It is about 25' of the 3/8 copper tubing just like you'd find anywhere

The chiller is made to fit his old kettle which was a wide/low 8 gallon canning kettle. I'd like to rework the design a bit to make sure that it fits my rig which is a little smaller in diameter and taller. I'm not trying to make this thing look perfect by any stretch, it is just that it doesn't fit in my current brewpot.

Anyone have any good advice for bending this tube without fatally crimping or otherwise damaging the tubing? Also, I don't have access to a corny keg which seems to be the preferred form for shaping the tubing.

Thanks for your guidance and lessons learned.

 
Reply With Quote
Old 03-23-2007, 05:39 PM   #2
david_42
 
david_42's Avatar
Recipes 
 
Oct 2005
Oak Grove, Oregon, USA
Posts: 25,595
Liked 152 Times on 143 Posts


If you have something cylindrical that is about the size or a bit smaller, place it inside the chiller coil. Then hold one end of the coil steady and drag the other end around as if you were tightening a spring. An extra hand or two would make this easier.
__________________
Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk

 
Reply With Quote
Old 03-23-2007, 08:25 PM   #3
BarryNL
Recipes 
 
Feb 2007
Netherlands
Posts: 88

I think filling it with water and sealing the ends should help stop any crimping - not sure how you'd accomplish this though.
__________________
Brewing: Dunkelweizen '09, alt.beer.dusseldorf
Bottled: Erebus American IPA, Big 4-0 Barley Wine, Oranje Tripel, Got Milk Stout?
Planning: Oktoberfest, Peter the Grain RIS
Drinking: Abbey Daze, Best of 2008

 
Reply With Quote
Old 03-23-2007, 08:30 PM   #4
Brewsmith
 
Brewsmith's Avatar
Recipes 
 
Aug 2005
Torrance, CA
Posts: 6,252
Liked 62 Times on 58 Posts


A spring bender works great for bending copper tubing without kinking it.
Click image for larger version

Name:	Spring Bender.JPG
Views:	255
Size:	4.3 KB
ID:	1289
__________________
Fermenting:#160 Apollo/Calypso Pale Ale
Kegged:#153 Old Helicon Barleywine 2013, #157 Irish Red, #158 Mosaic IPA, #159 Bravo/Delta ESB
Up Next:Brown Porter, American Stout, Imperial Stout
My Recipes
Tuba Sonata

Smith & Co. Custom Tap Handles

 
Reply With Quote
Old 03-23-2007, 08:33 PM   #5
Alamo_Beer
 
Alamo_Beer's Avatar
Recipes 
 
Aug 2006
Manor, Tx
Posts: 2,439
Liked 9 Times on 6 Posts


either get a spring bender or fill it with salt....the salt will let it bend without crimping

good luck!

 
Reply With Quote
Old 03-23-2007, 08:52 PM   #6
Craig5_12
Recipes 
 
Jan 2007
Valley Springs, CA
Posts: 290

I did this with a 50' chunk I turned into my CFC. (BTW pulling 50' of garden hose over semi-straight tubing isn't easy) But the easiest way is to find something that fits inside the coils as is. Then as it's coiled around it start unrolling it and stepping on the coils as it comes off. (Your weight shouldn't be enough to crush the tube) In this manner, it only tightens up on whatever you have it coiled around and won't kink. Very easy.
To coil it back up just wrap it around whatever you think will fit inside your kettle. Although why not just bump up to a CFC? You're only about $15 away....unless you need the torch and solder and then you're about $35.
I've found that the spring bender is very helpfull for small tight bends....using it on 25 feet would be a major chore.

 
Reply With Quote
Old 03-23-2007, 08:55 PM   #7
johnsma22
HBT_SUPPORTER.png
 
johnsma22's Avatar
Recipes 
 
Jun 2006
Taunton, MA
Posts: 1,964
Liked 80 Times on 60 Posts


Copper get work hardened the more it is worked and bent. You can anneal it by heating up the entire length with a torch until it glows cherry red, working yourself around a little bit at a time. This will make the copper very malleable again and allow you to bend it around something cylindrical without kinking. The more you bend it the stiffer it becomes. Hey, I don't like the sound of that!
__________________
Cheers,
John

 
Reply With Quote
Old 03-23-2007, 09:04 PM   #8
SAS98M
Recipes 
 
Jan 2007
N.E.PA.
Posts: 234

"He said stiff"

 
Reply With Quote
Old 03-23-2007, 09:40 PM   #9
weetodd
Recipes 
 
Oct 2006
Seattle. WA
Posts: 197
Liked 1 Times on 1 Posts


Thanks all for the responses. I don't have to do much to it as it is at least in a circle, they are just too large and not spread out very much.

One follow up, do you think a standard pail will work or do i need something hard to bend against (which is why everyone suggests a corny keg). I think I probably answered my own question but just not trying to screw it up.

Also, being kind of new to this, on a counterflow, would I need a pump or could I work one off of a racking cane siphon? My current kettle setup doesn't have a valve.

Cheers.

 
Reply With Quote
Old 03-23-2007, 09:49 PM   #10
Brewsmith
 
Brewsmith's Avatar
Recipes 
 
Aug 2005
Torrance, CA
Posts: 6,252
Liked 62 Times on 58 Posts


Use a big coffee can
__________________
Fermenting:#160 Apollo/Calypso Pale Ale
Kegged:#153 Old Helicon Barleywine 2013, #157 Irish Red, #158 Mosaic IPA, #159 Bravo/Delta ESB
Up Next:Brown Porter, American Stout, Imperial Stout
My Recipes
Tuba Sonata

Smith & Co. Custom Tap Handles

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Copper Wort Chiller snipper_cr Beginners Beer Brewing Forum 6 09-10-2009 08:31 PM
Will a 25' 3/8'' copper wort chiller do the job? Q2XL All Grain & Partial Mash Brewing 8 03-26-2009 02:46 PM
bending copper hammer one Equipment/Sanitation 27 07-01-2008 04:21 AM
Bending copper? aekdbbop Equipment/Sanitation 38 10-01-2007 09:50 PM
non-copper wort chiller Comos Equipment/Sanitation 12 01-11-2007 03:12 PM


Forum Jump