MD hard water - what styles? - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Brew Science > MD hard water - what styles?

Reply
 
Thread Tools
Old 06-28-2011, 11:09 PM   #1
clex25
Recipes 
 
Sep 2009
MD
Posts: 31


Hey All. I've been reading some tutorials and I just wanted to confirm a few assumptions I had about my water. Looks like my Ca and Mg levels are all in order, but it seems like my Total Hardness is pretty high.

It seems that I will best be suited to brewing styles with an SRM between 5.0-10.0. I also realize that my pH level is a bit high for mashing.

What styles are best for me to brew, and are there any changes I should be making to the water that would have a highly noticeable effect?

Ward Report -

pH 7.5
TDS 227
me/L 4.1/4.0

Sodium, Na 16
Potassium, K 2
Calcium, Ca 53
Magnesium, Mg 8
Total Hardness, CaCO3 166
Nitrate, NO3-N 2
Sulfate, SO4-S 18
Chloride, Cl 36
Carbonate, CO3 <1
Bicarbonate, HCO3 105
Total Alkalinity, CaCO3 86
Fluoride, F 0.79
Total Iron, Fe <0.01

 
Reply With Quote
Old 06-29-2011, 01:33 AM   #2
Nateo
 
Nateo's Avatar
Recipes 
 
Jul 2010
Bennett Springs, MO
Posts: 2,050
Liked 39 Times on 30 Posts


I'd probably use phosphoric acid to knock down the bicarbonate. That should get your RA low enough to do most any paler beer. You might need to increase the RA if you brew something with a lot of roast malt, but with that water I'd say 9 times out of 10 you'll need to lower the mash pH, not raise it.
__________________
To paraphrase Dr. England - "Off-flavors smooth with time. So do mountains. Brew it right from the start!"

My blogsite: http://nateobrew.blogspot.com/

 
Reply With Quote
Old 06-29-2011, 11:44 AM   #3
ajdelange
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Aug 2010
McLean/Ogden, Virginia/Quebec
Posts: 9,294
Liked 1493 Times on 1140 Posts


The hardness is not, in general, a problem - in fact it is beneficial from the mash pH point of view and it is the pH of the mash, not the water, which is significant. That is determined mostly by the grain bill and the alkalinity with the hardness having a secondary role. Many beers, notably Helles, and Bohemian Pilsner are brewed with very soft water and these beers are best if the home brewer follows suit. In the course of doing that many of us have concluded that low mineral water makes the best, if not the most "authentic" beers but this is a somewhat controversial position.

The water you have is fine for brewing beers from 4 SRM (the lowest a home brewer can expect to do) to as high as you want to go.

The sulfate will be high (54 mg/L as SO4--) for those beers that use noble hops but will need to be supplemented for those beers for which assertive hoppiness is desired.

The alkalinity is high enough to push mash pH into the undesirable range unless acid is added in some form to most beers or the alkalinity is reduced or both. It's easy to reduce alkalinity and sulfate at the same time by diluting the water with RO or DI. There are some guidelines in the Prime in the Stickies here.

This is very nominal water and should present few problems for you.

 
Reply With Quote
Old 06-29-2011, 05:20 PM   #4
clex25
Recipes 
 
Sep 2009
MD
Posts: 31

Thanks for the feedback...
One question
Quote:
Originally Posted by ajdelange View Post
The sulfate will be high (54 mg/L as SO4--) for those beers that use noble hops but will need to be supplemented for those beers for which assertive hoppiness is desired.
Did you mean the sulfate will be fine or high? If you meant high for noble, I'm not understanding why I would need to supplement it for more heavily hopped beers. Thanks for the clarification.

 
Reply With Quote
Old 06-29-2011, 05:49 PM   #5
ajdelange
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Aug 2010
McLean/Ogden, Virginia/Quebec
Posts: 9,294
Liked 1493 Times on 1140 Posts


The sulfate thing seems to be a personal preference thing. British pale ales were brewed with waters with hundreds of mg/L sulfate in them and so "genuine" British pale ales should have high levels of sulfate. Many prefer those same beers with appreciably less sulfate so what you do here depends on whether you like them genuine or like them tasting better (or think they do taste better with the high sulfate).

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Help with Hard, Alkaline Water HopBlooded Brew Science 28 11-14-2014 07:10 PM
Help Analyzing Water Report - Very Hard Water BrewThruYou Brew Science 6 04-18-2012 06:17 PM
Hard Water lschiavo Brew Science 22 05-27-2011 12:50 PM
Water quality, what to do....Hard water and high pH. BroadStreetBrewery Brew Science 9 09-11-2010 04:12 AM
Tried and True Water Profiles for Classic Styles Picobrew Brew Science 8 01-29-2010 10:49 PM


Forum Jump