CIP Pump - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > CIP Pump

Reply
 
Thread Tools
Old 03-21-2011, 03:53 AM   #1
StMarcos
Recipes 
 
Apr 2008
Sebastopol, CA
Posts: 973
Liked 34 Times on 27 Posts



Getting the bits together to CIP my Brewhemoth. The basic idea is that there will be a 3G bucket under the bottom dump, with a submersible pump. This pump will be hooked to a flex tube running up outside to a modified 4''tc at the top of the brewhemoth. On the other side of the tc will be the spray ball, about 6'' down from the top. The question is about the pump. I bought a 1/4hp sump-type pump (no float switch though). I'm pretty sure this will drive my st pats rotating ball (discontinued model), but am worried that the pump will die quickly in hot pbw and starsan. It's rated to 77F and I will be using it at 120F or so. Think I'll fry it? Also worried that there could be some bits that will corrode in starsan. Should I be? I can return the pump if need be. It was about 80 bucks. The thing is, I want a submersible pump so I can just drop it in the bucket. It's also not rated for continuous duty (draining a swimming pool).

Was this just a bad buy on my part, or are the specs very conservative?

Cheers, etc.

 
Reply With Quote
Old 03-21-2011, 03:44 PM   #2
WalterAtMarchPump
Sponsor
HBT_SPONSOR.png
 
WalterAtMarchPump's Avatar
Recipes 
 
Dec 2010
Glenview, IL
Posts: 704
Liked 52 Times on 40 Posts


You could probably get it to work for you, but would need to do a little investigating as to the construction of the pump. I'm not familiar with all the protocols on brewing yet but with the "starsan" (cleaning chemical I assume) you would need to check it its compatible with what ever the pump is made out of, be it plastic or metal materials. And I'm not only talking about the big parts...you need to look at the materials that would be in contact with the chemical like and screws/washers/ nuts/power cords etc... Most submersible sump-pump types have a shaft seal to worry about. For domestic use they don't have to have high temp seals as all it sees is room temp type water. So first thing I would do is see if there's a way to change out the seal to something more robust if possible. Teflon if available would probably be best all around.

-Walter

 
Reply With Quote
Old 03-22-2011, 05:47 PM   #3
ScubaSteve
HBT_SUPPORTER.png
 
ScubaSteve's Avatar
Recipes 
 
May 2007
New Bern, NC
Posts: 3,677
Liked 83 Times on 57 Posts


It should work well....just don't expect it to work forever. The PBW will damage the seals over time, but this can be helped by rinsing well after use.

About CIP- The preferred way to do it is to supply fresh cleaning agent (called a sequestrant for good reason) and then have the vessel drain the wastewater elsewhere. You'll plug your sprayball if you recirc gunk, and your stuff will never truly be clean....just recirculated debris.

 
Reply With Quote
Old 03-22-2011, 08:01 PM   #4
StMarcos
Recipes 
 
Apr 2008
Sebastopol, CA
Posts: 973
Liked 34 Times on 27 Posts


That makes sense, but I was hoping to be able to save on detergent by recirculating just a small amount. Maybe I can do a drain-to-waste with mains water to get most gunk, then recirculate pbw. Then a drain-to-waste rinse. Then recirculate saniclean....

 
Reply With Quote
Old 03-22-2011, 09:09 PM   #5
ScubaSteve
HBT_SUPPORTER.png
 
ScubaSteve's Avatar
Recipes 
 
May 2007
New Bern, NC
Posts: 3,677
Liked 83 Times on 57 Posts


That's pretty much what I do...but I don't sanitize when I'm done....that happens next brew when I put the wort in. Just make sure you drain out any residual water or you'll grow mold.

 
Reply With Quote
Old 03-23-2011, 12:41 AM   #6
StMarcos
Recipes 
 
Apr 2008
Sebastopol, CA
Posts: 973
Liked 34 Times on 27 Posts


Yeah I guess I meant to let dry before storage, then sanitize before the ferment. Should probably run some clean water through the pump to get the saniclean out before storing the pump.

 
Reply With Quote
Old 03-26-2011, 05:03 AM   #7
StMarcos
Recipes 
 
Apr 2008
Sebastopol, CA
Posts: 973
Liked 34 Times on 27 Posts


Well I have it all rigged up, and it doesn't work. Doesn't spin, I should say. There is an impressive amount of water coming out the drain back to the bucket. There is also a huge amount of water coming out of the ball at the join between the rotating and stationary parts. It's hard for me to believe that the pump is too wimpy. The warning on the cord says 130F max, while the manual says 78F max. The thermal shutdown did not engage after running for 10min at 120F, so I'm good there.

The pump is a Simer 1/4hp.
Head (ft) / gpm
0 / 30
3 / 27
5 / 25
10 / 21
15 / 15
20 / 6
22 / 0

I guess I should see how long it takes to move 5G out of one bucket an into another, so I can see what sort of pressure the pump is seeing. There is about 5' of 1/2''id reinforced pvc tubing between the pump and the ball. Any advice? Kinda pissed right now (American, not Aussie).

 
Reply With Quote
Old 03-26-2011, 05:20 AM   #8
StMarcos
Recipes 
 
Apr 2008
Sebastopol, CA
Posts: 973
Liked 34 Times on 27 Posts


Guess my next plan of attack is:

Find the actual flow
Try city mains pressure
Call st. pats

 
Reply With Quote
Old 03-26-2011, 02:00 PM   #9
RiverCityBrewer
 
RiverCityBrewer's Avatar
Recipes 
 
Dec 2009
Cincinnati, OH
Posts: 816
Liked 32 Times on 28 Posts


I have one of these:

http://www.harborfreight.com/1-hp-30...oat-93819.html

Been working great for almost 2 years now and has plenty of oomph and can handle 5mm particles without clogging. Haven't worried about water temp that much, never really thought about it actually. Running the pump with straight tap water it heats up fairly rapidly and the water temp maxes out at about 100F. Another plus is that when the pump dies they are pretty cheap to replace.

 
Reply With Quote
Old 04-07-2011, 01:11 AM   #10
StMarcos
Recipes 
 
Apr 2008
Sebastopol, CA
Posts: 973
Liked 34 Times on 27 Posts


Bought another pump after returning the last one. This time I got a Simer 1/2hp pump - the biggest the hardware store had. Made in Italy. Still doesn't work. Most of the water sprays out from where the ball meets the body. Makes me think that there is a flaw in the design, and why St Pats doesn't carry it anymore. Sprays heaps of water, but no spinning. Maybe it needs to be mounted vertically, with the ball pointing up? If so, I'm screwed, because I need to have the ball come in from the top of the fermenter.

This thing wasn't cheap. Maybe 1/2hp still isn't enough?
Click image for larger version

Name:	sprayball.JPG
Views:	875
Size:	76.2 KB
ID:	23502  

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
non submersible pump self priming pump for glycol terrazza Equipment/Sanitation 4 08-11-2016 04:58 PM
Breast pump to replace march pump? instapman Equipment/Sanitation 69 03-21-2012 07:30 PM
Looking for a pump to replace my March 809 Pump EinGutesBier Equipment/Sanitation 24 07-30-2011 06:19 PM
Dual purpose March Pump as a Rain Barrel Pump nanotigerbrewer Equipment/Sanitation 6 12-01-2010 08:18 PM
March pump wont pump high temperatures. above 190... rshosted Equipment/Sanitation 17 07-12-2010 09:05 PM


Forum Jump