Consistently low alcohol content - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Fermentation & Yeast > Consistently low alcohol content

Reply
 
Thread Tools
Old 02-20-2011, 04:24 AM   #1
rkzink
Recipes 
 
Oct 2010
Indianapolis, IN
Posts: 11


So I just bottled my third batch of beer (all three batches were Brewer's Best kits). I have been consistently getting alcohol contents that are on the low end of the range listed on the kit (and sometimes lower). My OG and FG readings have been within their ranges (and I've made sure to stir appropriately and make temperature corrections).

So I realize that if you're on the low end of the spectrum for the OG and the high end for the FG, then you're going to end up with a low alcohol content. My question is, what am I doing to consistently have this happen? Or what can I do to fix this? I don't want to have to add ingredients to my kits to "make it right," but would rather fix my brewing process (since this has consistently happened over three different kits/recipes).

Questions? Suggestions?

Thanks!
Rebecca

 
Reply With Quote
Old 02-20-2011, 04:33 AM   #2
beninan
Recipes 
 
Mar 2010
Maine
Posts: 998
Liked 17 Times on 16 Posts


what were the recipes? gravity readings? brewing processes? fermentation processes?

there are multiple different factors that can affect gravity. Without knowing the specifics of your process, we can only make a wild guess.
__________________
"Stop giving me credit for those stupid quotes! For that last time it wasn't me! STFU NOOB!" <-- Benjamin Franklin

 
Reply With Quote
Old 02-20-2011, 04:33 AM   #3
Kayos
 
Kayos's Avatar
Recipes 
 
Dec 2006
Santa Clarita, SoCal
Posts: 1,364
Liked 8 Times on 8 Posts


Boil longer/more rolling boil

Use less water.

Stir before you take readings

Solved
__________________
Being Dealt (kegged): Carbed Crystal light lemonade for the boys, Delta Bravo IPA, Applewinder
Primary: Climbing stout
Primary #2: ESB
Big Blind: Pucker Bitter
Small Blind:
Tasty Remembrances: White 'N Nerdy, Dynamite Red (Hop bursted), APA, The Bonaduce (irish Red), runners stout, ridgeback brown,

from my big ass computer sitting on my floor

 
Reply With Quote
Old 02-20-2011, 04:34 AM   #4
WuWeiBrewing
Recipes 
 
Apr 2009
Denver, Colorado
Posts: 26

What types of beers were these? I'm assuming a dry yeast that came with the kit too?

But by the way, dropping a pound or so of corn sugar (dextrose) into your boil will bump up the ABV too.

 
Reply With Quote
Old 02-20-2011, 04:36 AM   #5
ChshreCat
 
ChshreCat's Avatar
Recipes 
 
Aug 2008
Camano Island, Washington
Posts: 11,533
Liked 540 Times on 432 Posts


If you're in the recommended range, it's not THAT much of a difference. The recommended ranges are that wide.

Don't go dumping sugar or anything in it just to get more alcohol. Good beer is more important than alcohol. If alcohol is more important than taste, then go buy some Steel Reserve or something.

 
Reply With Quote
Old 02-20-2011, 05:00 AM   #6
rambler
Recipes 
 
Jan 2011
Elko, Nevada
Posts: 245
Liked 5 Times on 5 Posts


Ditto ChshreCat, If you want more Al Cohol than change you could switch up recipes too, and keep an eye on those temps.
__________________
It's better to sit in the alehouse and think of church than to sit in church and think about the alehouse.

Martin Luther

 
Reply With Quote
Old 02-20-2011, 05:19 AM   #7
Homebrewtastic
Recipes 
 
Jun 2009
San Antonio, Texas
Posts: 1,043
Liked 26 Times on 23 Posts


How far on the high end of the spectrum are you getting on the F.G. ? Post your measurements and we can give you some better advice.

Like Cheshire said though, I wouldn't be concerned with the lower alcohol. However if your beer is under-attenuating and ending up sweet... and that's what you want to fix it's a different story.
__________________
On Deck:
Primary: Lambic-ish
Kegged: Das Funken Weisse, Un Poquito Wylde
Bottled: Epik Barleywine, Chocolate Chili Pumpkin Porter, EKG Amber
Adventures in Zymurgy - Homebrewing and Sour Beer Blog

 
Reply With Quote
Old 02-20-2011, 01:53 PM   #8
jmhart
Recipes 
 
Aug 2010
Atlanta,GA
Posts: 130

As mentioned, use less water/longer, more vigorous boil. Part of homebrewing is learning your specific brewing conditions. It's possible, for example, that you don't experience as much boil off as the kit assumes. Add, say, a half gallon less than you've been adding or boil for an extra 15-30 minutes. This will increase your OG. However, if you're using extract, I'd recommend just adding a little less water, instead of boiling longer.

For decreasing FG, make a starter. Under attenuated beer is almost always caused by too little yeast. Also, make sure you are aerating properly. Good aeration and the correct amount of yeast will ensure a proper FG.

 
Reply With Quote
Old 02-20-2011, 02:12 PM   #9
rocketman768
HBT_LIFETIMESUPPORTER.png
 
rocketman768's Avatar
Recipes 
 
Feb 2008
Evanston, IL
Posts: 1,083
Liked 25 Times on 22 Posts


Quote:
Originally Posted by rkzink View Post
So I just bottled my third batch of beer (all three batches were Brewer's Best kits). I have been consistently getting alcohol contents that are on the low end of the range listed on the kit (and sometimes lower). My OG and FG readings have been within their ranges (and I've made sure to stir appropriately and make temperature corrections).
Thanks!
Rebecca
How are you getting the alcohol reading? The percent alcohol depends on the difference between OG and FG. Specifically, ABV=131*(OG-FG). I hope you're not reading the alcohol percent straight off the hydrometer when your beer is done.

 
Reply With Quote
Old 02-20-2011, 03:21 PM   #10
rkzink
Recipes 
 
Oct 2010
Indianapolis, IN
Posts: 11

Ok, for example. The last batch I did was the Scottish Ale from Brewer's Best. I followed the directions for brewing (I even set a timer so that I know I am steeping/boiling for the proper length of time).

The OG that I came up with was 1.035 and the kit specified that the OG should be 1.034 to 1.038.

The FG that I had was 1.014, and the kit specified that it should be 1.010 to 1.014.

The kit said the final alcohol content should be between 3.25% and 3.5%. My calculations put it at 2.75%.

I don't mind having a beer with low alcohol content, but I just wish it was more in the range of what the recipe says. I get that if you're on the low end of the OG and the high end of the FG, then you won't get the expected alcohol content, but since this keeps happening, I want to know what I can do to bump the content up slightly.

I like the suggestions of boiling longer/adding less water. Would I increase the boiling time after adding LME/DME then?

Thanks!

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
alcohol content SjbSam Fermentation & Yeast 2 01-01-2011 10:29 PM
Dry Yeast to help carbonate a high alc content Belgian Sun Devil Fermentation & Yeast 24 12-22-2010 04:27 AM
Alcohol Content Tedpro Fermentation & Yeast 12 05-14-2010 08:02 PM
Fruit Beer and Alcohol Content? Druish_00 Fermentation & Yeast 3 01-02-2010 03:32 PM
Alcohol Content Calculator hopsoda Fermentation & Yeast 5 08-07-2009 01:28 PM


Forum Jump