Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Placement of a RIMS tube
Reply
 
Thread Tools
Old 12-23-2010, 01:59 AM   #1
dutch101st
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2009
Location: Roseville, CA, California
Posts: 243
Liked 1 Times on 1 Posts

Default Placement of a RIMS tube

I am ready to mount the RIMS tube on my brewstand...which way is going to be the most efficeint?

Horizontal?

Vertical?


__________________
Kegged: AIR
Primary: AIR
Secondary:
Secondary:

On Tap: NADA
Bottled: Store baught swill

Atomic Robot Brewing- Beware the Robot Uprising!!

http://robotarmageddon.com/wp-conten...t-Uprising.jpg
dutch101st is offline
 
Reply With Quote
Old 12-23-2010, 04:43 AM   #2
stlbeer
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
stlbeer's Avatar
Recipes 
 
Join Date: Jan 2008
Location: Fenton, MO
Posts: 946
Liked 36 Times on 35 Posts
Likes Given: 92

Default

Quote:
Originally Posted by dutch101st View Post
I am ready to mount the RIMS tube on my brewstand...which way is going to be the most efficeint?

Horizontal?

Vertical?
Well, it needs to fill so as to remove all of the air and it needs to drain so it doesn't grow anything.

I think I'm going to mount my on a diagonal.



I used a cross instead of a tee on the bottom and installed a valve so i can dump the contents. Otherwise I guess I could have put disconnects on the input and output sides, but this will drain better.


stlbeer is offline
 
Reply With Quote
Old 12-23-2010, 05:23 AM   #3
dutch101st
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2009
Location: Roseville, CA, California
Posts: 243
Liked 1 Times on 1 Posts

Default

I don't have the luxury of installing a drain...I have a one piece tube that I purchased from Brewer's Hardware (nice piece too!). I am thinking of doing it vertical and having it able to be removed from the brackets of which it will be mounted on.
__________________
Kegged: AIR
Primary: AIR
Secondary:
Secondary:

On Tap: NADA
Bottled: Store baught swill

Atomic Robot Brewing- Beware the Robot Uprising!!

http://robotarmageddon.com/wp-conten...t-Uprising.jpg
dutch101st is offline
 
Reply With Quote
Old 12-26-2010, 10:15 PM   #4
dutch101st
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2009
Location: Roseville, CA, California
Posts: 243
Liked 1 Times on 1 Posts

Default

Well, after a lot of thinking and plannning, this is what I can up with:









I still have the wireing to finish, get the rest of the fitting in place, then test. I am about 50% done with my .5 upgrade (will be brewery 2.5...3.0 would be a complete overhaul as I did in September)
__________________
Kegged: AIR
Primary: AIR
Secondary:
Secondary:

On Tap: NADA
Bottled: Store baught swill

Atomic Robot Brewing- Beware the Robot Uprising!!

http://robotarmageddon.com/wp-conten...t-Uprising.jpg
dutch101st is offline
 
Reply With Quote
Old 12-26-2010, 10:30 PM   #5
limulus
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
limulus's Avatar
Recipes 
 
Join Date: Oct 2009
Location: ATL Burbs, Georgia
Posts: 1,275
Liked 69 Times on 57 Posts
Likes Given: 91

Default

That looks like the same tube I have. I mounted mine vertically first with the element on bottom like yours. However, I found that my element worked better with the tube mounted horizontally. I currently have my temp probe on the output of the MT and I think I may move it to the RIMS tube or at least experiment:
__________________


"Always do sober what you said you'd do drunk. That will teach you to keep your mouth shut."
-Ernest Hemingway
limulus is offline
 
Reply With Quote
Old 12-27-2010, 11:30 PM   #6
dutch101st
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2009
Location: Roseville, CA, California
Posts: 243
Liked 1 Times on 1 Posts

Default

Well, got my parts from Bargain Fittings (ALWAYS a good experience with them!!) and I think I am hooked/sold/enamoured with CamLocks...but I digress...

I have got the RIMS tube even closer to being ready for a full on water test...just awaiting the low density heater element. Got the old HEX coil from my old RIMS removed and the holes plugged. I got everything teflon taped up and ready (except the temp probe)...the element should be here tomorrow and will get it mounted and then will do a water test- and if that goes well, then off we go with brewing with the RIMS tube in full production!!

ALL HAIL THE RETRO ATOMIC ROBOT BREWERY.

Pics of today's work...






__________________
Kegged: AIR
Primary: AIR
Secondary:
Secondary:

On Tap: NADA
Bottled: Store baught swill

Atomic Robot Brewing- Beware the Robot Uprising!!

http://robotarmageddon.com/wp-conten...t-Uprising.jpg
dutch101st is offline
 
Reply With Quote
Old 12-28-2010, 12:11 AM   #7
drumming102
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2010
Location: Eaton, Ohio
Posts: 195
Liked 1 Times on 1 Posts

Default

Is the valve on the RIMS tube for redundancy sake or is it used for somthing?
__________________
Primary -
Secondary -
Conditioning -Coffee Ground Stout, Ed's crazy Apfelwein
Drinking - American light, Blue Moon Clone
On Tap- English bitter, BB Octoberfest, BB IPA
Surly Midget Brewery
drumming102 is offline
 
Reply With Quote
Old 12-28-2010, 02:01 AM   #8
dutch101st
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2009
Location: Roseville, CA, California
Posts: 243
Liked 1 Times on 1 Posts

Default

Its to insure there is liquid in the tube...extra precaution.


__________________
Kegged: AIR
Primary: AIR
Secondary:
Secondary:

On Tap: NADA
Bottled: Store baught swill

Atomic Robot Brewing- Beware the Robot Uprising!!

http://robotarmageddon.com/wp-conten...t-Uprising.jpg
dutch101st is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
RIMS Heating Tube Emian Equipment/Sanitation 33 11-20-2013 11:53 PM
Question for those of you who have the Brewer's Equip RIMS Tube limulus Equipment/Sanitation 5 09-29-2010 11:57 PM
RIMS: MLT/E-Keggle outlets, dip tube VS bottom valve MonkeyWrench Equipment/Sanitation 3 12-08-2009 03:56 PM
CFC Placement ScottD13 Equipment/Sanitation 5 07-08-2009 08:36 PM
SS braid, copper tube, bazooka tube??? Joetuo Equipment/Sanitation 12 10-26-2007 01:58 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS