"superb" burner replacement hose - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > "superb" burner replacement hose

Reply
 
Thread Tools
Old 10-29-2010, 01:14 AM   #1
tieflyer
Recipes 
 
May 2010
reading, pa
Posts: 176
Liked 2 Times on 2 Posts



Ok, I purchased a "superb" Professional Cookers one burner model second hand, and this is what I can find on it -
"Powerful, low-pressure burners allow you to boil, steam, deep-fry or stew any meal. Large, cast-iron cooking surface gives complete heat distribution. 1 and 2 burner models available. "

my question is this, anyone know where I can find a replacement hose/regulator for it? it has the old tank hookup on it, and I need to replace the hose so it will attach to the new tanks. anyone have any specs on these burners? btu output etc?


any and all help would be appreciated!



 
Reply With Quote
Old 10-29-2010, 01:36 AM   #2
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 69 Times on 62 Posts


This adjustable regulator should work with that burner:

http://www.agrisupply.com/product.as...4640&sid=&eid=



 
Reply With Quote
Old 10-30-2010, 01:40 PM   #3
tieflyer
Recipes 
 
May 2010
reading, pa
Posts: 176
Liked 2 Times on 2 Posts


Quote:
Originally Posted by Catt22 View Post
This adjustable regulator should work with that burner:

http://www.agrisupply.com/product.as...4640&sid=&eid=
thanks but I need a female hookup on the burner side and I believe it is 3/8's.

 
Reply With Quote
Old 10-30-2010, 02:21 PM   #4
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 69 Times on 62 Posts


Post a close up pic of the burner. Typically, you can remove the fitting on the burner and replace it with the one on the hose. Usually these are 1/4" NPT x 3/8" flare and often the orifice is integral with this fitting;sometimes there's also a small ball valve also attached. Without a pic, I can only guess. Apparently the original configuration for the burner was "low pressure", however, you can use an adjustable pressure regulator with a high pressure orifice for vastly improved performance. I think that's the same burner that the SQ-14 uses, but need a pic to know for sure.

 
Reply With Quote
Old 10-31-2010, 07:13 PM   #5
tieflyer
Recipes 
 
May 2010
reading, pa
Posts: 176
Liked 2 Times on 2 Posts


figured out how to put on images

 
Reply With Quote
Old 10-31-2010, 07:17 PM   #6
tieflyer
Recipes 
 
May 2010
reading, pa
Posts: 176
Liked 2 Times on 2 Posts


[IMG][/IMG]
all together
[IMG][/IMG]
unscrewed regulator
[IMG][/IMG]

 
Reply With Quote
Old 10-31-2010, 09:14 PM   #7
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 69 Times on 62 Posts


Can you post a pic of the burner and whatever fitting is attached? There should be an orifice right at the air damper on the burner.

 
Reply With Quote
Old 11-01-2010, 12:01 AM   #8
tieflyer
Recipes 
 
May 2010
reading, pa
Posts: 176
Liked 2 Times on 2 Posts


the female end of pic one goes on the burner. I purchased a 3/8 hose type one hose that fit, but it was too short.

 
Reply With Quote
Old 11-01-2010, 12:20 AM   #9
tieflyer
Recipes 
 
May 2010
reading, pa
Posts: 176
Liked 2 Times on 2 Posts




 
Reply With Quote
Old 11-01-2010, 01:02 AM   #10
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 69 Times on 62 Posts


Yes, that appears to be a 3/8" male flare fitting. You should be able to buy adapters to get from that to whatever is on the regulator hose that you buy. What was too short? The hose on the new regulator? How long does it need to be? Most regulators come equipped with a 3 ft. hose IIRC, which should be the same length as your old one. My old BBQ has that same type of hose and regulator shown in the first pics.



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
What SIze Oetiker Clamp For 1/2" ID Silicon Hose On 1/2" Barbs HenryHill Equipment/Sanitation 5 11-03-2015 07:07 PM
0-30 PSI burner VS 20 PSI w/ "brass control valve" jmhart Equipment/Sanitation 6 10-01-2010 12:26 AM
1/2" Silicone Hose Tubing illin8 Equipment/Sanitation 26 09-20-2010 03:32 PM
1/2" black pipe to propane hose dunleav1 Equipment/Sanitation 0 04-13-2009 10:12 PM
2nd burner, even for the "non-sculptured"...? beergears Equipment/Sanitation 2 07-25-2008 02:13 PM


Forum Jump