How Many Temp Inputs EHERMS Brewers? - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Electric Brewing > How Many Temp Inputs EHERMS Brewers?
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 10-11-2010, 03:10 AM   #1
EuBrew
Recipes 
 
Apr 2009
Columbus, OH, Ohio
Posts: 610
Liked 31 Times on 24 Posts



I'm in the process of designing my system and ordering parts and I'm curious how many temp inputs everyone is using.

I plan on one in HLT for determining strike and sparge temps, one in BK for PID control of boil, and one in my dedicated HEX coil for monitoring mash temps. The one at the HEX will actually be at the input of the sparge arm into the MLT.

Anyone have any suggestions for other places to monitor temps? I'm considering one in the MLT for backup of my HEX.


__________________
Primary 1: empty
Primary 2: empty
Primary 3: empty
Secondary 1: empty
Secondary 2: empty
Secondary 3: empty

Kegged: Nada
Bottled Nada

Planned: Sierra Nevada Celebration clone
CBC Bodhi IPA



I may be naive but I make up for that with inexperience!!

 
Reply With Quote
Old 10-11-2010, 01:17 PM   #2
CoalCracker
Recipes 
 
Sep 2009
Macungie, Pa
Posts: 1,666
Liked 106 Times on 65 Posts


I only have one. I place the temp probe in the HLT and set a couple degrees higher to offset for temp loss. Then I have a thermometer in my MT.



 
Reply With Quote
Old 10-11-2010, 01:44 PM   #3
pickles
 
pickles's Avatar
Recipes 
 
Feb 2008
Columbus
Posts: 2,004
Liked 49 Times on 41 Posts


Brewtroller 2.0 allows you to monitor temps in the mash at up to three locations and it averages the three for a more consistent mash temp. I suggest you do that since your using the Brewtroller for control.
__________________
Gaptooth Brewhouse

 
Reply With Quote
Old 10-11-2010, 01:59 PM   #4
EuBrew
Recipes 
 
Apr 2009
Columbus, OH, Ohio
Posts: 610
Liked 31 Times on 24 Posts


Quote:
Originally Posted by pickles View Post
Brewtroller 2.0 allows you to monitor temps in the mash at up to three locations and it averages the three for a more consistent mash temp. I suggest you do that since your using the Brewtroller for control.
Thanks! I just ordered my BT gear last night

Where would you suggest the three inputs be monitored? I'm thinking at the sparge arm inlet, and one in the MLT around the same area as the ones that will go into my BK and HLT, where would you recommend the third probe be placed?
__________________
Primary 1: empty
Primary 2: empty
Primary 3: empty
Secondary 1: empty
Secondary 2: empty
Secondary 3: empty

Kegged: Nada
Bottled Nada

Planned: Sierra Nevada Celebration clone
CBC Bodhi IPA



I may be naive but I make up for that with inexperience!!

 
Reply With Quote
Old 10-12-2010, 02:39 AM   #5
kal
HBT_SUPPORTER.png
 
kal's Avatar
Recipes 
 
Nov 2006
Ottawa, Canada
Posts: 2,486
Liked 332 Times on 218 Posts


Quote:
Originally Posted by EuBrew View Post
I'm in the process of designing my system and ordering parts and I'm curious how many temp inputs everyone is using.

I plan on one in HLT for determining strike and sparge temps, one in BK for PID control of boil, and one in my dedicated HEX coil for monitoring mash temps. The one at the HEX will actually be at the input of the sparge arm into the MLT.

Anyone have any suggestions for other places to monitor temps? I'm considering one in the MLT for backup of my HEX.
I have:

1. One at the output of the HLT for holding the water temp.

2. One in the boil kettle for boiling for the PID, though it's not needed as water boils at 212 and you could use a 2 cent resistor instead. There's no need to 'control' a PID running in manual mode. I do find that displaying and controlling the temperature in the boil kettle has benefits: It helps me minimize the chance of 'boil-overs'. I run the boil kettle heating element in 'automatic' mode and set the temperature to just below boiling. I then also set an alarm to sound once that temperature reached. The wort is then automatically heated to just below the boiling point without actually going any higher, and an alarm is sounded. I then switch over to 'manual' mode and continue heating while watching and stirring to avoid the initial boil overs.

3. My third probe used to be at the HEX output but it was always the same temp as the HLT temp, so I moved it to the MLT output so that I could instead monitor ramp times. It's not really needed.

Kal

 
Reply With Quote
Old 10-12-2010, 03:31 AM   #6
pickles
 
pickles's Avatar
Recipes 
 
Feb 2008
Columbus
Posts: 2,004
Liked 49 Times on 41 Posts


In my setup I have temp sensors in the following places: one in HLT (3.5" from bottom), one at RIMS outlet, two in MT (3.5" and 10" from bottom**), one in BK (8" from bottom), one in plate chiller outlet and plan to put one at the cooling water outlet.

**If you place one temp sensor too high it could possibly be out of the mash and affect temperature control.

I suppose you could put one in the sparge outlet. The way my system is set up the sparge water always runs through the RIMS; it cleans out residual wort, step mashes and monitors sparge temps. You didn't exactly describe your setup in the OP and I know that your using a Brewtroller from other conversations. So your not just using the BK temp sensor for PID control (which is technically the Brewtroller operating in PID mode); it will be used to start the boil timer which in turn starts the hop addition timer/alerts, it will allow AutoBoil (a feature in BT 2.0) to throttle back the boil to prevent boil overs, and finally BrewTroller uses the BK temperature sensor as the "Chiller Wort In" value and its displayed in oth locations on the LCD and BTRemote. From what I understand BT 2.1-2.X will have Chilling logic which you may find useful in the future. You definitely need one in the BK.
__________________
Gaptooth Brewhouse

 
Reply With Quote
Old 10-12-2010, 03:44 PM   #7
EuBrew
Recipes 
 
Apr 2009
Columbus, OH, Ohio
Posts: 610
Liked 31 Times on 24 Posts


Thanks pickles. Sorry I didn't specify my setup, brain is a little cloudy from painkillers because I had surgery a few days ago, damn getting old sucks! Hopefully the cloud will be lifting soon (i.e. body healing) since I've got lots and lots of parts on the way!

My planned setup is a EHERMS with a dedicated HEX for recirculation of mash. I'll still use a coil in the HLT that will be used as a chiller. Last 15 min of boil I'll pump through HLT coil to sanitize and start whirlpool. At "flame out" I'll fill the HLT with ice and H2O to start the chill.

So temp probes will be in the HLT, BK, MLT (2) and the output of the HEX, this is what I meant by the sparge inlet. I don't know that I need any more probes than that but the more I think about it I think I'll just order an extra 4" probe in case I want to add at some point. Thanks again for all the input!!
__________________
Primary 1: empty
Primary 2: empty
Primary 3: empty
Secondary 1: empty
Secondary 2: empty
Secondary 3: empty

Kegged: Nada
Bottled Nada

Planned: Sierra Nevada Celebration clone
CBC Bodhi IPA



I may be naive but I make up for that with inexperience!!

 
Reply With Quote
Old 10-13-2010, 12:52 AM   #8
Maltose
Recipes 
 
May 2010
Frederick, MD
Posts: 466
Liked 2 Times on 2 Posts


Quote:
Originally Posted by kal View Post
I have:

1. One at the output of the HLT for holding the water temp.

2. One in the boil kettle for boiling for the PID, though it's not needed as water boils at 212 and you could use a 2 cent resistor instead. There's no need to 'control' a PID running in manual mode. I do find that displaying and controlling the temperature in the boil kettle has benefits: It helps me minimize the chance of 'boil-overs'. I run the boil kettle heating element in 'automatic' mode and set the temperature to just below boiling. I then also set an alarm to sound once that temperature reached. The wort is then automatically heated to just below the boiling point without actually going any higher, and an alarm is sounded. I then switch over to 'manual' mode and continue heating while watching and stirring to avoid the initial boil overs.

3. My third probe used to be at the HEX output but it was always the same temp as the HLT temp, so I moved it to the MLT output so that I could instead monitor ramp times. It's not really needed.

Kal
Kal, I always thought having the probes at the output of the vessels would mean the input would be much much hotter. I want to put my mash probe in the outlet of the HEX for recirc. What made you change it to the MLT outlet?

 
Reply With Quote
Old 10-13-2010, 01:25 AM   #9
kal
HBT_SUPPORTER.png
 
kal's Avatar
Recipes 
 
Nov 2006
Ottawa, Canada
Posts: 2,486
Liked 332 Times on 218 Posts


My mash probe at the outlet of my HEX (recirc) was always the same temp as the HLT so it was a useless thing to measure. The two temps on my control panel always read the same.

I moved the mash probe to the output of my mash so that it shows me how fast the mash rises in temp (something useful).

Kal

 
Reply With Quote
Old 10-13-2010, 09:57 PM   #10
Budzu
Recipes 
 
Mar 2009
Chattanooga, TN
Posts: 747
Liked 17 Times on 16 Posts


I started with 3 probes, hex output, hlt bottom, and bk bottom. I realized shortly after that my mash was sitting about 3 degrees lower than my hex output and HLT.

Now I pull my bk temp probe and stick it straight in the recirculating mash during the mash. It is very important to have something in there, or in the mash output, for accuracy. I am using brewer's hardware 12" probes and the BCS-460.

If I were to revise or start again, I'd probably leave out the hex output probe and have 4 probes total, HLT, MT top, MT output, and BK.


__________________
Countertop Brutus Budzu-style

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Electrical Primer for Brewers CodeRage Electric Brewing 219 11-14-2015 04:41 PM


Forum Jump