first time with a keg set up....and issues with keg lid seal - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Bottling/Kegging > first time with a keg set up....and issues with keg lid seal
Cool Brewing Corny 5G & Mini Giveaway
Sign-up To NEW HBT Article Newsletter - Brewing Articles Direct To You!

Reply
 
Thread Tools
Old 09-20-2010, 11:01 AM   #1
SWAMPER
HBT_SUPPORTER.png
 
SWAMPER's Avatar
Recipes 
 
Join Date: Jul 2009
Location: Bel Air Md.
Posts: 65
Liked 1 Times on 1 Posts


Just got my first keg kit and just want to know if Iím doing something wrong ? got a single premium keg kit form keg connection shipping was quick and all was packaged great pulled the keg out of the box and pulled the pressure release valve and the keg had pressure so all looked good, so I let all the pressure out of the keg and cleaned it all up, and here comes the question/problem had the keg half full of water/cleaning solution and was shaking it around and turned the keg over and water was leaking out of the lid, I tried resetting the lid and flipping it around and still leaking even put a new seal on the lid and still leaking so I thought maybe it needs to be under pressure to seal so went got my tank filled and I could kind of get it to seal but it would not last that long till the c02 leaked out, am I doing something wrong ? the bail latch is not very tight (not much pressure to latch) should there be a good amount of pressure on the latch to hold the lid? Should the keg be water/air tight without any c02 added ??

Thanks



 
Reply With Quote
Old 09-20-2010, 11:43 AM   #2
oojuxeoo
Recipes 
 
Join Date: Nov 2009
Location: Philly burbs
Posts: 25

Try sticking a penny under each leg of the lid. Also maybe some food grade lube on the o ring.



 
Reply With Quote
Old 09-20-2010, 11:53 AM   #3
SWAMPER
HBT_SUPPORTER.png
 
SWAMPER's Avatar
Recipes 
 
Join Date: Jul 2009
Location: Bel Air Md.
Posts: 65
Liked 1 Times on 1 Posts


i did put grease on the new o-ring for the lid but still leaked, how tight should the lid latch be when you flip it down ?

 
Reply With Quote
Old 09-20-2010, 12:04 PM   #4
hal2814
Recipes 
 
Join Date: Jul 2009
Location: Commerce, GA
Posts: 556
Liked 17 Times on 12 Posts


The keg will NOT hold a seal until it's under pressure. I have 6 different kegs and all but 2 of them are quirky when it comes to getting a seal. Doing the initial seal around 30PSI and then hitting the relief valve to bring down the pressure helps me a lot. The rest is just fiddling around with the lid until it seals right. I even have one keg that absolutely will not seal unless the lid is facing a certain way. The good news is once you get the hang of it, it'll be second nature to you.

 
Reply With Quote
Old 09-20-2010, 12:35 PM   #5
SWAMPER
HBT_SUPPORTER.png
 
SWAMPER's Avatar
Recipes 
 
Join Date: Jul 2009
Location: Bel Air Md.
Posts: 65
Liked 1 Times on 1 Posts


I filled the keg with water and put the new seal in with lube and lifted up on the lid handle to try and put pressure on the seal and it help seal it, I put about 12psi on it then shut the c02 off after it was set (the lid did seal) but like 1 hour later it had leaked out, Iíll give KC a call and see just wanted to make sure that I wasnít doing something wrong

 
Reply With Quote
Old 09-20-2010, 01:35 PM   #6
knotquiteawake
Recipes 
 
Join Date: Aug 2009
Location: Dallas TX
Posts: 1,142
Liked 20 Times on 18 Posts
Likes Given: 19


I've been having seal problems with my keg from keg connection as well. I have to push the lid to the side while latching it down or I get a bad seal because the mouth of the keg is slightly deformed. I tested it several times under about 15psi with some starsan and it pretty consistently bubbled if I sealed it without pushing it away from the direction the seal handle pulls the lid to seal it.

 
Reply With Quote
Old 09-20-2010, 01:40 PM   #7
P-J
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Join Date: Mar 2010
Location: Charlotte, NC
Posts: 3,337
Liked 300 Times on 235 Posts
Likes Given: 496


Quote:
Originally Posted by SWAMPER View Post
I filled the keg with water and put the new seal in with lube and lifted up on the lid handle to try and put pressure on the seal and it help seal it, I put about 12psi on it then shut the c02 off after it was set (the lid did seal) but like 1 hour later it had leaked out, Iíll give KC a call and see just wanted to make sure that I wasnít doing something wrong
Your description does not suggest a leak. You had water in the keg and the CO≤ will disolve into the water thus dropping the pressure. If the keg was empty, then the test would be valid.

I did a write up on keg seal issues a bunch of years ago. I think it might help you find the cause and give you a fix for the issues.
Keg Lid Geometry & Adjustment

 
Reply With Quote
Old 09-20-2010, 01:49 PM   #8
SWAMPER
HBT_SUPPORTER.png
 
SWAMPER's Avatar
Recipes 
 
Join Date: Jul 2009
Location: Bel Air Md.
Posts: 65
Liked 1 Times on 1 Posts


Iíll read your info, but it did the same thing with nothing in it, so I tried filling it with water to see if that would help but didnít seem to help, just hate to fill it with beer and go through all this so trying to figure it all out ahead of time, I did notice that one of the brackets that are spot welded to the lid is bent over some not sure if thatís putting uneven pressure on the lid or not and not letting it seal correctly

 
Reply With Quote
Old 09-20-2010, 02:53 PM   #9
bja
Recipes 
 
Join Date: Nov 2007
Location: Pittsburgh
Posts: 2,054
Liked 166 Times on 124 Posts


Spay it with starsan after you pressurize it to show where the leak is. It could be the relief valve.

 
Reply With Quote
Old 09-20-2010, 03:19 PM   #10
SWAMPER
HBT_SUPPORTER.png
 
SWAMPER's Avatar
Recipes 
 
Join Date: Jul 2009
Location: Bel Air Md.
Posts: 65
Liked 1 Times on 1 Posts


did it was the lid, going to go over it tonight and try squeeze the arms in some so it will put more pressure on the lid and double check the keg lip and make sure there is no dents or anything that would let it leak



 
Reply With Quote
Reply

Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Keg won't seal spiny_norman Bottling/Kegging 2 03-20-2010 06:42 PM
Need to seal keg? kmat123 Bottling/Kegging 5 12-29-2009 06:24 AM
Keg won't seal, but... jacksonbrown Bottling/Kegging 13 06-02-2008 10:50 PM
Keg did not seal lostforatime Bottling/Kegging 14 01-27-2007 11:17 PM
getting a keg to seal? mrkeeg Bottling/Kegging 5 05-09-2005 10:55 PM


Forum Jump