Ball valve question - Little Giant Pump - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > Ball valve question - Little Giant Pump

Reply
 
Thread Tools
Old 08-23-2010, 12:34 AM   #1
Twang
Recipes 
 
Jan 2009
Posts: 206
Liked 3 Times on 3 Posts



I am in the process of building a 1 tier setup with 2 kettles and converted cooler. I will be using 1 pump and quick disconnects to transfer the liquids. After reading through the forum I am leaning towards purchasing a Little Giant 3-MD-HC pump for my setup. This pump has a 3/4" intake and 1/2" discharge.

My question:
What size hoses/ball valves/connections should I use on each vessel? All 3/4 inch and put a 1/2" to 3/4" adapter on the pump discharge?

 
Reply With Quote
Old 08-23-2010, 12:36 AM   #2
wyzazz
Recipes 
 
Aug 2009
Atwater, OH
Posts: 4,315
Liked 56 Times on 53 Posts


I'm doing just the opposite, I've seen many on here do the same.
__________________
Quote:
Originally Posted by Revvy View Post
And I'd like to see my 1.080 beers ready from grain to glass in a week, and served to me by red-headed twin penthouse pets wearing garter belts and fishnet stockings, with Irish accents, calling me "master luv gun," but we can't always get what we want can we? :)

 
Reply With Quote
Old 08-23-2010, 01:23 AM   #3
gpogo
Recipes 
 
Jul 2007
Palmdale, CA
Posts: 119
Liked 1 Times on 1 Posts


I was thinking about this too. Then I found:
http://www.plumbersurplus.com/Prod/L.../1006?RefID=CJ which has 1/2" intake/outtake

and you can pretty much follow http://www.homebrewtalk.com/wiki/index.php/March_Pump
for what to connect where.

(I have not actually bought this pump yet, but plan on doing so soon)
__________________
Primary -
Secondary 1 - Hibiscus Saison
Secondary 2 -
Secondary 3 - Malkore's Not So Ancient Orange Mead(2.5 gal)
Secondary 4 -
Gallon Fermentor - Joe's Ancient Orange, Joe's Quick Grape Mead, Pomegranate Mead
Bottled/aging - Sunshine Wheat Clone, Fat Tire Clone, Hard Cider, Scotch Ale, Orange Blossom Sweet Mead
Coming soon... - Weizenbock, Belgian Wit, Apfelwein

 
Reply With Quote
Old 08-23-2010, 12:14 PM   #4
wyzazz
Recipes 
 
Aug 2009
Atwater, OH
Posts: 4,315
Liked 56 Times on 53 Posts


Quote:
Originally Posted by gpogo View Post
I was thinking about this too. Then I found:
http://www.plumbersurplus.com/Prod/L.../1006?RefID=CJ which has 1/2" intake/outtake

and you can pretty much follow http://www.homebrewtalk.com/wiki/index.php/March_Pump
for what to connect where.

(I have not actually bought this pump yet, but plan on doing so soon)
If you're going to get the 3-MD-MT-HC then you might as well just get a March or Chugger pump, the 3-MD-HC is 1/12HP, the MT-HC is 1/25HP.
__________________
Quote:
Originally Posted by Revvy View Post
And I'd like to see my 1.080 beers ready from grain to glass in a week, and served to me by red-headed twin penthouse pets wearing garter belts and fishnet stockings, with Irish accents, calling me "master luv gun," but we can't always get what we want can we? :)

 
Reply With Quote
Old 08-23-2010, 03:57 PM   #5
Twang
Recipes 
 
Jan 2009
Posts: 206
Liked 3 Times on 3 Posts


Quote:
Originally Posted by wyzazz View Post
I'm doing just the opposite, I've seen many on here do the same.
I thought I read somewhere that it is better to restrict the outflow and not the inflow... any truth to this?

Also, if you use all 1/2" hoses and fittings, will that decrease the pumps performance vs. using all 3/4"?

 
Reply With Quote
Old 08-23-2010, 04:13 PM   #6
ScubaSteve
HBT_SUPPORTER.png
 
ScubaSteve's Avatar
Recipes 
 
May 2007
, DC
Posts: 3,680
Liked 84 Times on 58 Posts


Yes, you can restrict the outlet, not the intake. I essentially did what you describe but with triclovers. My intake is a full 1" and my output is ~7/8". The 3-MD-HC can handle the higher volume and so you can go a little bigger with the output. I'm not sure 1/2" tubing is going to decrease its performance, as the output IS 1/2".....but with such a high flow rate you would definitely do better with bigger tubing.

 
Reply With Quote
Old 08-23-2010, 06:46 PM   #7
Twang
Recipes 
 
Jan 2009
Posts: 206
Liked 3 Times on 3 Posts


Quote:
Originally Posted by ScubaSteve View Post
Yes, you can restrict the outlet, not the intake. I essentially did what you describe but with triclovers. My intake is a full 1" and my output is ~7/8". The 3-MD-HC can handle the higher volume and so you can go a little bigger with the output. I'm not sure 1/2" tubing is going to decrease its performance, as the output IS 1/2".....but with such a high flow rate you would definitely do better with bigger tubing.
So you have a 3/4" to 1" adapter on the pump intake and a 1/2" to 7/8" adapter on the pump output?

 
Reply With Quote
Old 08-23-2010, 09:44 PM   #8
ScubaSteve
HBT_SUPPORTER.png
 
ScubaSteve's Avatar
Recipes 
 
May 2007
, DC
Posts: 3,680
Liked 84 Times on 58 Posts


Kinda. I have a 3/4" MPT x 1.5" Triclover screwed into the intake. That is then clamped to a 1" Barb x 1.5" Triclover. Then 1" PEX is slid over that barb.

On the outlet, it's a 1/2" FPT x 1.5" Triclover married up with a 3/4" Barb x 1.5" Triclover.

1" Triclover pipe has an ID of ~7/8"; 1.5" Triclover pipe has an ID of ~1.3".

Confusing, I know Just understand that my pipes are bigger than the pump is designed for, and the flow rate should make up for it.

 
Reply With Quote
Old 08-23-2010, 10:13 PM   #9
Randar
All your Ninkasi are belong to us
HBT_LIFETIMESUPPORTER.png
 
Randar's Avatar
Recipes 
 
Sep 2008
Wheeling, IL
Posts: 40,920
Liked 5411 Times on 5217 Posts


I have the TE-5.5-MD-HC and this has 1" inlet and 3/4" outlet. I plan to step it down to take 1/2" input and 1/2" output with the valve on the outlet side, as recommended. There is no point for me to try to do 3/4" or 1" inlet as I will be pumping through CFC or recirculating the mash and I can't work a hard-plumbed system into my current setup.

I have read of others doing this as well with similar pumps.

 
Reply With Quote
Old 08-23-2010, 10:14 PM   #10
Randar
All your Ninkasi are belong to us
HBT_LIFETIMESUPPORTER.png
 
Randar's Avatar
Recipes 
 
Sep 2008
Wheeling, IL
Posts: 40,920
Liked 5411 Times on 5217 Posts


Quote:
Originally Posted by ScubaSteve View Post
Kinda. I have a 3/4" MPT x 1.5" Triclover screwed into the intake. That is then clamped to a 1" Barb x 1.5" Triclover. Then 1" PEX is slid over that barb.

On the outlet, it's a 1/2" FPT x 1.5" Triclover married up with a 3/4" Barb x 1.5" Triclover.

1" Triclover pipe has an ID of ~7/8"; 1.5" Triclover pipe has an ID of ~1.3".

Confusing, I know Just understand that my pipes are bigger than the pump is designed for, and the flow rate should make up for it.
Can you get PEX for boiling temps? That sounds like a great option if available.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Valve order question (ASCO, BASO, BALL) chilipepper Brew Stands 3 06-05-2010 03:06 PM
Little giant pump 3-MD-HC weizen Brew Stands 50 06-02-2010 03:00 PM
Little Giant pump choice FenoMeno Brew Stands 7 05-13-2010 10:36 PM
Cooler MLT / Ball Valve wes_d Kettles, Mash Tuns & Hot Liquor Tanks 4 07-25-2009 11:15 AM
Ball valve in a keggle? Yooper Kettles, Mash Tuns & Hot Liquor Tanks 10 03-03-2009 03:51 AM


Forum Jump