Beer Faucet Coupling Gasket Size? - Home Brew Forums
Home Brew Forums > Home Brewing Beer > DIY Projects > Kegerators & Keezers > Beer Faucet Coupling Gasket Size?
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 08-21-2010, 11:19 PM   #1
Conodor
Recipes 
 
Aug 2005
St. Clair Shores
Posts: 231
Liked 3 Times on 3 Posts





In the Above Picture it's the D1200B gasket, it's the gasket that goes between the Shank and the Tail. I can't find the size anywhere. trying to save a few bucks since i need to replace 9.

I have searched everywhere, no places seems to want to give the size.

thanks@!


__________________
5th Street Brewery
7 days without a beer makes one weak.

C.R.A.F.T. Member

(Most replys from my cell sorry for mispellin)

 
Reply With Quote
Old 08-21-2010, 11:53 PM   #2
bendavanza
Recipes 
 
Aug 2008
Oak CLiff, TX
Posts: 2,179
Liked 18 Times on 16 Posts


measure the best one you have and look to http://www.oringsandmore.com/servlet/StoreFront
they have a size chart



 
Reply With Quote
Old 08-22-2010, 12:02 AM   #3
Conodor
Recipes 
 
Aug 2005
St. Clair Shores
Posts: 231
Liked 3 Times on 3 Posts


unfortunately the 4 i have are installed. I just ordered 5 more faucets but they don't come with the gasket.
__________________
5th Street Brewery
7 days without a beer makes one weak.

C.R.A.F.T. Member

(Most replys from my cell sorry for mispellin)

 
Reply With Quote
Old 08-22-2010, 12:10 AM   #4
wildwest450
Registered User
Recipes 
 
Dec 2007
Posts: 8,969
Liked 172 Times on 157 Posts


I have an old faucet laying around that looks like that one, the washer was a dead on 7/8". It isn't an o-ring, it is a flat washer. An o-ring may work fine?

 
Reply With Quote
Old 08-22-2010, 12:19 AM   #5
Conodor
Recipes 
 
Aug 2005
St. Clair Shores
Posts: 231
Liked 3 Times on 3 Posts


thanks the diameter is what i needed. didn't want to take apart my system to figure it out.

i'll post what i order from mcmasters and my results.

I'm thinking that this might be what i try.

208 1/8" 5/8" 11.56 per Pack of 80 Part number 94115k208


http://www.mcmaster.com/?orderview=new#94115k208/=8i8wbo

but looking more at it part number 94115K115 might be a closer fit

http://www.mcmaster.com/?orderview=n...15k115/=8i9e4j
__________________
5th Street Brewery
7 days without a beer makes one weak.

C.R.A.F.T. Member

(Most replys from my cell sorry for mispellin)

Reason: added link

 
Reply With Quote
Old 08-22-2010, 02:09 AM   #6
wildwest450
Registered User
Recipes 
 
Dec 2007
Posts: 8,969
Liked 172 Times on 157 Posts


The second one should be real close, mine measured a tad over 11/16" inside diameter, but it could be stretched a little from taking it out several times.

 
Reply With Quote
Old 11-01-2012, 08:21 PM   #7
Pash91
Recipes 
 
Dec 2009
Wherever Drinks Are
Posts: 185
Liked 1 Times on 1 Posts


Quote:
Originally Posted by Conodor View Post
thanks the diameter is what i needed. didn't want to take apart my system to figure it out.

i'll post what i order from mcmasters and my results.

I'm thinking that this might be what i try.

208 1/8" 5/8" 11.56 per Pack of 80 Part number 94115k208


http://www.mcmaster.com/?orderview=new#94115k208/=8i8wbo

but looking more at it part number 94115K115 might be a closer fit

http://www.mcmaster.com/?orderview=n...15k115/=8i9e4j
Did you ever figure out which one this is? I just had to pull a gasket from one of my faucets to install on my stout faucet (the gasket was completely disintegrated). I'd like to have a few as spares



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY Beer Faucet Lock DocUzuki Kegerators & Keezers 27 04-12-2016 06:34 PM
Tapping a SS coupling on a keg Marc_Cote Kettles, Mash Tuns & Hot Liquor Tanks 8 02-15-2010 01:45 AM
Cooler coupling? evandy Kettles, Mash Tuns & Hot Liquor Tanks 2 01-26-2010 12:27 PM
coupling placement BucksPA Brew Stands 4 01-19-2010 02:08 AM
Where to weld coupling on MLT? Mongo64 Kettles, Mash Tuns & Hot Liquor Tanks 2 10-12-2009 06:03 PM


Forum Jump