Fast Force Carbing - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Fast Force Carbing

Reply
 
Thread Tools
Old 06-29-2010, 01:37 PM   #1
Cpt_Kirks
Recipes 
 
Sep 2008
Lakeland TN
Posts: 3,723
Liked 47 Times on 41 Posts



I usually hit a newly filled keg with 30psi overnight, then set it at 12psi for about 10 days. This gives good results.

I need to speed that up a bit for this weekend. I kegged 10 gallons of wheat last night (5 of Hefe and 5 of cherry). I have them at 30psi and need them drinkable by Saturday.

Since they are wheats, they need to be good and fizzy, but not overcarbed. How soon should I drop the pressure?




 
Reply With Quote
Old 06-29-2010, 01:44 PM   #2
SweetSounds
Recipes 
 
Jan 2010
Des Moines, Iowa
Posts: 1,425
Liked 20 Times on 19 Posts


If I'm in a hurry, and they are already at cooler temperature, I'll set for 30 PSI and rock them back and forth like a teeter-totter for a while. Then put them back in the cooler at serving pressure for a bit and test. You can repeat that until you get close, but just short of carbed. Then let them go at serving pressure for the last bit.

If you're careful, and creep up to proper carbonation, you can get there in a few hours probably...


__________________
Quote:
Originally Posted by Ecnerwal View Post
What does the primary pressure gauge on the tank tell us? That's right, the temperature. Put it on a scale if you want to know how much is in it...
Put some duct tape over the gauge - Or better yet - Replace the high pressure gauge with a plug - High pressure gauges are useless!

 
Reply With Quote
Old 06-29-2010, 01:58 PM   #3
pcollins
Recipes 
 
Mar 2010
Cambridge, ON
Posts: 565
Liked 31 Times on 29 Posts


+1

I did this just yesterday with a pale ale. I kegged it on Saturday night and let it cold crash on Sunday with only a layer of CO2 and no coupling head on it. Yesterday I drew off half a pint to clear it a bit and then set the psi to about 25 and did the teeter totter thing about every 10-15 minutes or so for an hour or so (you can see how carefully I took notes. LOL ). That all started about 1:30. I then let it sit for the rest of the afternoon at 10 psi.

When I drew a couple of pints last night they started a bit too foamy but the beer was carbed and quite drinkable.

I don't normally do this, I'm much more a set and forget person but I blew a keg on Saturday night and wanted some homebrew on tap for a gathering of homebrewers this evening at my place. It seemed to work fine so I may do it again if I'm in a hurry. The only thing I don't like about it is the fact that I have to pay attention to it! I would much rather just have the keg sit there and carb on it's own. YMMV

 
Reply With Quote
Old 07-01-2010, 01:56 PM   #4
Cpt_Kirks
Recipes 
 
Sep 2008
Lakeland TN
Posts: 3,723
Liked 47 Times on 41 Posts


I purged and sampled both kegs last night. After two days at 30psi, they are fairly well carbed. SWMBO thinks they are fine, but I want more fizz. I dropped them to 20psi. If they are carbed tonight, I will just drop them to 12psi and be done with it.

The cherry needs more cherry extract, though. Can't even detect it now.


 
Reply With Quote
Old 07-01-2010, 04:44 PM   #5
RebelHouse32
Recipes 
 
Jan 2010
Dayton, Ohio
Posts: 27

You could always buy a carbonation stone, that will carb your beer up anywhere from a couple hours to 24 depending on your pressure. I have heard of people using a carb stone and getting it carbonated in 1 hour.
__________________
[COLOR="Red"][B][FONT="Comic Sans MS"]The Dayton Beer Company

 
Reply With Quote
Old 07-01-2010, 07:12 PM   #6
babalu87
Recipes 
 
Feb 2008
Middleborough, MA
Posts: 1,895
Liked 8 Times on 7 Posts


COLD keg
30 PSI
Lay it on the floor with the gas line down
Roll it with your feet (shoes are recommended..........its COLD!)

4 minutes for English beers
5 minutes for most anything else
6 minutes for German Wheats and Belgian beers

 
Reply With Quote
Old 07-01-2010, 08:10 PM   #7
Gritsak
Recipes 
 
Aug 2009
Posts: 601
Liked 14 Times on 13 Posts


I start with the keg cold, hit it at 30psi for ~24hrs. After that i bleed, adjust to 12-14psi and shake that about 3-4 time during the day, about 3min each time. Let it sit overnight and it's good to go. Nice thing about this is there's no chance of overcarbonating when you shaking at the desired psi (based on temp/desired CO2 volume)



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
does fast force carbonation = green beer? treemind Bottling/Kegging 21 06-01-2009 02:14 PM
Fast Carbing dataz722 Bottling/Kegging 20 12-31-2008 03:07 AM
Force Carbing Dominator6 Bottling/Kegging 5 05-04-2008 04:05 AM
I force carbed, but bottled 2 gallons to fast... Chello Bottling/Kegging 1 03-14-2008 12:35 AM
Force Carbing? MilwaukeesBus Bottling/Kegging 9 03-14-2007 10:07 PM


Forum Jump