3rd AG Brew/Coleman xtreme mashtun problems - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > 3rd AG Brew/Coleman xtreme mashtun problems

Reply
 
Thread Tools
Old 03-24-2010, 12:28 AM   #1
Bamfordjf
Recipes 
 
Mar 2010
Little Rock,AR
Posts: 23


I did my 3rd AG brew this past weekend and continue to have problems with strike temp and temp drops. This is driving me absolutely nuts! I preheated my tun once with about 2 or 3 gallons of 175 deg water and within 15 min the temp dropped to below 150. I tried it again with 180 deg water and even though it was preheated it still dropped to low 160s. Finally I put about about 7 gallons of 200 deg water in let it sit for 30 min. When it reached my strike temp ~165 deg, I added my grain and stirred. It stayed at 150 pretty much for an hour.

I had 10 lbs of grain.
Beersmith said 165 strike temp after adj for equipment
I have a 70 qt Coleman Xtreme cooler w/ SS braid

What the heck am I doing wrong/not doing? I have heard great things about the cooler!

 
Reply With Quote
Old 03-24-2010, 12:46 AM   #2
mightynintendo
HBT_LIFETIMESUPPORTER.png
 
mightynintendo's Avatar
Recipes 
 
Aug 2009
Raleigh, NC
Posts: 2,710
Liked 134 Times on 105 Posts


I don't think you're doing anything wrong. You might try adjusting your dough-in temp a couple degrees if you wanted to hit 152 but that sounds about right. Other than that I don't see that you're doing anything wrong.
__________________
'Kilgore Trout once wrote a short story which was a dialogue between two pieces of yeast. They were discussing the possible purposes of life as they ate sugar and suffocated in their own excrement. Because of their limited intelligence, they never came close to guessing that they were making champagne.'

—Kurt Vonnegut, Breakfast of Champions

 
Reply With Quote
Old 03-24-2010, 12:56 AM   #3
Bamfordjf
Recipes 
 
Mar 2010
Little Rock,AR
Posts: 23

Should I really have to preheat it 3 times? Each time I drained the water and reheated it. Granted heat does escape whenever I open the lid to check temp.

 
Reply With Quote
Old 03-24-2010, 12:56 AM   #4
EonBlue66
 
EonBlue66's Avatar
Recipes 
 
Oct 2008
Phoenix, AZ
Posts: 210
Liked 2 Times on 2 Posts


was the 7 gallons @ 200 just to preheat the tun?
__________________
We'll ride the spiral to the end and may just go where no one's been.

Spiral out. Keep going, going...

 
Reply With Quote
Old 03-24-2010, 01:01 AM   #5
Bamfordjf
Recipes 
 
Mar 2010
Little Rock,AR
Posts: 23

Quote:
Originally Posted by EonBlue66 View Post
was the 7 gallons @ 200 just to preheat the tun?
lol yes. That was the third time heating the cooler up too. Then i put 12.5 qts of 175 deg water in there and let it drop to strike temp before dough in.

 
Reply With Quote
Old 03-24-2010, 01:04 AM   #6
DarkSide
 
DarkSide's Avatar
Recipes 
 
Feb 2009
Barrie, Ontario
Posts: 71
Liked 1 Times on 1 Posts


Have you checked the temperature of your grains. Beersmith has the Strike/Infusion Temp Tool. You can make adjustments to your strike water temp based on the temperature of your grain. Maybe your grain is cooler then normal. This will allow you to make adjustments.

When I do my mash in, I add the strike water, then add my grains right away. If you check off adjust for equipment, beersmith adds the extra degrees knowing your going to lose some heat to heating the cooler. So you don't need to wait for the temp to drop to a normal strike temperature without equipment adjustment. Is that what you are doing, or are you waiting to add grains?

I brew in my garage, and if it's a cooler day, I may add a few degrees to what should be my strike temperature.

Your mash temps should be between 150 degrees to 156 degrees on average.

Is your equipment setup right in Beersmith?

 
Reply With Quote
Old 03-24-2010, 01:05 AM   #7
Myke_J
 
Myke_J's Avatar
Recipes 
 
Oct 2009
Lawrence, KS, Kansas
Posts: 218

I have the exact same setup as you and I usually add most of my strike water at around 180 and close the lid. I will finish getting everything setup, crush my grain, refill my HLT, and then check temp. The MLT will usually be around 160-165 after around 20-30 mins. Then I add the rest of my strike water and wait until it's all at the strike temp I need based off my grain bill, usually 10-12 degrees over my mash temp, and then dough in. Slowly dump in grain while stirring constantly and once all the grain is in I'm usually within 1-2 degrees of my mash temp. I let the grain settle for about 10 mins, stir it again and then let it sit until it's converted. The most temp loss I've had over an hour is about 1.4 degrees and that was outside in the wind with the temps in the lower 40's. Last batch I hit my mash temp at 155.2 and finished 60mins later at 154.5.

Reason: Edited to reflect the laws of thermodynamics ;)

 
Reply With Quote
Old 03-24-2010, 01:06 AM   #8
EonBlue66
 
EonBlue66's Avatar
Recipes 
 
Oct 2008
Phoenix, AZ
Posts: 210
Liked 2 Times on 2 Posts


I think you may be looking at this wrong, just add some hot water to your tun I use about a gallon and let the cooler warm up. Empty the cooler and add your strike water around 12-14 degrees over your strike temp then dough in. After you dough in measure the temp it should be right around where you need it to be.
__________________
We'll ride the spiral to the end and may just go where no one's been.

Spiral out. Keep going, going...

 
Reply With Quote
Old 03-24-2010, 01:08 AM   #9
mightynintendo
HBT_LIFETIMESUPPORTER.png
 
mightynintendo's Avatar
Recipes 
 
Aug 2009
Raleigh, NC
Posts: 2,710
Liked 134 Times on 105 Posts


Oh, I didn't realize this was all at the same time. I thought these were all different attempts for some reason and the 200 deg attempt was your last attempt. No that doesn't sound quite right though my experience is with the 10 gal water coolers which only lose 1-2 degrees per hour with the lid on.
__________________
'Kilgore Trout once wrote a short story which was a dialogue between two pieces of yeast. They were discussing the possible purposes of life as they ate sugar and suffocated in their own excrement. Because of their limited intelligence, they never came close to guessing that they were making champagne.'

—Kurt Vonnegut, Breakfast of Champions

 
Reply With Quote
Old 03-24-2010, 01:12 AM   #10
mightynintendo
HBT_LIFETIMESUPPORTER.png
 
mightynintendo's Avatar
Recipes 
 
Aug 2009
Raleigh, NC
Posts: 2,710
Liked 134 Times on 105 Posts


Quote:
Originally Posted by Myke_J View Post
Last batch I hit my mash temp at 151.2 and finished 60mins later at 154.5.
That's interesting because it seems you managed to violate some basic laws of thermodynamics.
__________________
'Kilgore Trout once wrote a short story which was a dialogue between two pieces of yeast. They were discussing the possible purposes of life as they ate sugar and suffocated in their own excrement. Because of their limited intelligence, they never came close to guessing that they were making champagne.'

—Kurt Vonnegut, Breakfast of Champions

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Who here uses coleman xtreme cooler for a MLT? BeerPressure All Grain & Partial Mash Brewing 20 04-18-2010 04:58 AM
Coleman Xtreme too much? quixand Kettles, Mash Tuns & Hot Liquor Tanks 20 10-14-2009 09:02 PM
70 qt Coleman Xtreme & efficiencies illin8 Equipment/Sanitation 2 04-21-2009 06:30 PM
Coleman Xtreme 70qt for $29.99 at Academy ldkoehler Equipment/Sanitation 0 05-28-2008 08:12 PM
Xtreme Mashtun Build mozicodo Kettles, Mash Tuns & Hot Liquor Tanks 3 06-05-2007 04:23 AM


Forum Jump