Hydrometer Calibration Q's - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Hydrometer Calibration Q's

Reply
 
Thread Tools
Old 03-15-2010, 12:49 PM   #1
BuzzCraft
Recipes 
 
Jan 2009
Blacksburg, VA
Posts: 426
Liked 1 Times on 1 Posts



I've come to the conclusion that my hydrometer is off by a couple of points, so want to figure out how to be more accurate with what I have (i.e. I'm not going to shell out for a $75 pro set)

1. Everything I've come across for calibrating your hydrometer suggests to calibrate it using distilled water at the appropriate temperature. This doesn't seem right to me. I don't brew with distilled water. I brew with my tap water and want to know how much sugar is in it, right? So it seems I should use my tap water as the zeroing standard.

2. If my hydrometer is floating high, say by 2 points. Is it valid to simply weight it slightly (i.e. by adding a couple of pieces of tape, a piece of clay, whatever) to zero it in my calibration fluid?

Thoughts??

 
Reply With Quote
Old 03-15-2010, 02:03 PM   #2
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 70 Times on 63 Posts


Unless you have some unusual tap water, your hydrometer won't be able to detect the difference. Use either tap or distilled water to check it. Don't bother adding weights and such to the hydrometer to adjust it. It's much easier to simply add or subtract the error from the reading. Hight quality hydrometers are relatively inexpensive. I have three or four hydrometers and IIRC, the most expensive one was only about $15 and they all seem to be reasonably well calibrated and zero out with plain water distilled or tap. Paying $75 for a hydrometer would be really stupid IMHO.

 
Reply With Quote
Old 03-15-2010, 02:07 PM   #3
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 69,416
Liked 7843 Times on 5496 Posts


The hydrometer should be calibrated to distilled water, so you can see if it's reading correctly. But my tap water is very close, when I tested it. My tap water might be 1.0001.

Anyway, check it in 60 degree water. If it's reading high or low, just adjust your reading when you use it for beer. I had one that was .002 off. I just added .002 to each reading, and that worked fine.
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 03-15-2010, 02:37 PM   #4
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 70 Times on 63 Posts


Quote:
Originally Posted by YooperBrew View Post
The hydrometer should be calibrated to distilled water, so you can see if it's reading correctly. But my tap water is very close, when I tested it. My tap water might be 1.0001.

Anyway, check it in 60 degree water. If it's reading high or low, just adjust your reading when you use it for beer. I had one that was .002 off. I just added .002 to each reading, and that worked fine.
Are you really concerned about a difference of 1/10,000th? That's wild!

 
Reply With Quote
Old 03-15-2010, 02:42 PM   #5
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 69,416
Liked 7843 Times on 5496 Posts


Quote:
Originally Posted by Catt22 View Post
Are you really concerned about a difference of 1/10,000th? That's wild!
No, not at all. I'm just saying that my hydrometer in tap water reads very close to what it does in distilled water.
__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 03-15-2010, 02:45 PM   #6
samc
Recipes 
 
Aug 2008
Portland OR
Posts: 5,387
Liked 62 Times on 58 Posts


Probably more variation in the way each person reads the hydro then in the difference between tap & distilled.

Weighting it is a good idea as sometimes you forget to adjust the numbers. Of course it could be off in the other direction in which case hacking off a piece of it would not be so good. LOL

 
Reply With Quote
Old 03-15-2010, 08:37 PM   #7
BuzzCraft
Recipes 
 
Jan 2009
Blacksburg, VA
Posts: 426
Liked 1 Times on 1 Posts


Yeah, if there's nothing wrong with the concept of weighting the hydrometer (since mine floats high), I'd rather do that than subtract 1.7 points (or whatever it is) every time I use the thing.

tap water it is....

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Thermometer calibration Foreigner Equipment/Sanitation 28 07-25-2012 06:28 PM
MLT calibration Blindguardian Equipment/Sanitation 2 10-13-2010 12:59 PM
Hydrometer Calibration Jetsona Beginners Beer Brewing Forum 11 08-22-2009 02:43 PM
Cooler MLT calibration slim chillingsworth Equipment/Sanitation 3 04-09-2008 08:45 PM
Hydrometer calibration Cregar Equipment/Sanitation 11 03-26-2007 07:43 AM


Forum Jump